Haws 1900 Guide

04/17 Model 1900 Page 1 of 18
No. 2076963(4)
1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]
E-mail: [e-mail]  website: www.hawsco.com
Model 1900
Bottle Filler
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that this specific product is guaranteed against defective material or
poor workmanship for a period of one year from date of shipment. HAWS liability
under this warranty shall be discharged by furnishing without charge F.O.B. HAWS
Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS,
Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer
agrees that HAWS shall not be liable for general, special, or consequential damages
claimed to arise under the contract of sale. The drinking fountain manufactured by
HAWS is warranted to function if installation and maintenance instructions provided
are adhered to. The units also must be used for the purpose for which they were
intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

04/17 Model 1900 Page 2 of 18
REQUIRED TOOLS: Tubing cutter, #2 Phillips screwdriver, level, electric drill with standard
drill bits.
OTHER TOOLS (only needed for certain installation configurations – read installation
procedure for details): ABS cement, reciprocating saw or utility knife, hack saw or utility
knife, slip joint pliers.
LOCATION OF UNIT: The Model 1900 bottle filler is a wheelchair accessible drinking water
bottle filling facility. The height dimensions shown meet current ADA requirements. When
installing this unit, local, state or federal codes should be adhered to. If height other than
shown is required, then dimensions must be adjusted accordingly. Install a trap in the waste
line and a screwdriver stop in the supply line if required.
SUPPLY LINE: The minimum recommended line size is 1/4" OD copper or plastic tubing with
30-90 psi (2-6 ATM) pressure. Where sediment or mineral content is a problem, an inlet filter
is recommended.
PLUMBING CONNECTIONS: Inlet is 1/4“ O.D. push-in type fitting. Waste outlet is 1-1/4”
O.D. pipe.
MAINTENANCE: Periodically clean the strainer. Refer to 5874 Series Valve Manual for more
information.
INSTALLATION PROCEDURE
GENERAL NOTES:
1. For all plastic push-in type fitting connections, only connect NSF-61 copper or
plastic tubing. Stainless steel or glass tubing is not recommended. The
following assembly instructions must be followed to ensure a watertight
connection:
a. Cut tubing square and clean.
b. Mark from end of tube the length of insertion (See table below).
c. Push tube into the fitting until it bottoms out.
d. To remove, depress collet and pull tubing out.
Tube Sizes
O.D.
Tolerance Insertion Depth
1/4”
±.005”
11/16”
3/8”
±.005”
3/4”
1/2”
±.005”
7/8”
Step 1: Drain Setup
This bottle filler uses a reversible drain basin (see “Drain Setup” in installation
drawing).
•The drain basin can protrude from the front of the unit and drain into an electric
water cooler or drinking fountain.
•The drain basin can alternately protrude from the back of the unit and be hard-
plumbed to a waste line with a 1-1/4” O.D. slip joint connection (not supplied).

04/17 Model 1900 Page 3 of 18
Clean the sealing surfaces (the top surface of the drain basin and the bottom surface
of the bottle filler - shown below) with the supplied alcohol wipe; verify these surfaces
are clean and free of oil and grease.
Run a bead of RTV silicone (supplied) right alongside the groove, but not in the
groove, on the surface shown below. The size of the bead should be 1/8”-3/16” –
equal to the diameter of the RTV as it comes out of the tube (use the back of the
RTV cap to puncture and open the top fully). Creating this bead should use about
half the tube of RTV.
Check the RTV bead for thin sections, gaps, or areas where the bead does not touch
the plastic. Fill these in before proceeding. See pictures below for example.
Install the drain basin in the desired orientation (see “Drain Setup” in installation
drawing), using a screwdriver to tighten the 4 supplied #8 x 1/2" pan head screws.
Do not overtighten the screws.
Clean off any visible RTV. Allow the RTV to cure for 24 hours before running water
through the drain.
Note: The RTV
shown in these
pictures is white
instead of clear,
for the purpose of
clarity.
Groove
RTV bead (laid right up alongside the groove)

04/17 Model 1900 Page 4 of 18
Front drainage setup:
The drain will not empty into a fountain or water cooler bowl if the edge of the bowl is
further than 6” away from the wall. In this case, install the drain extender (see “Drain
Setup” in installation drawing), using ABS cement (not supplied) to seal the drain
extender to the drain basin. This allows for bowls that start up to 9” from the wall.
Rear drainage setup:
A relief for the drain basin must be cut into the wall (this cutout is made most easily
in Step 4).
Step 2: Supply Setup:
Stand-alone installation:
Supply tubing must be run into the 1/4" push-in inlet of the bottle filler (see sheet 1 of
installation drawing for location). The supplied 1/4” tubing is probably not sufficient
for most stand-alone installations.
Fountain/water cooler installation:
The 1/4" O.D. supply tubing (supplied) must be run from the water cooler/fountain to
the bottle filler. For this reason, it is recommended that a hole be cut in the top
surface of the water cooler/fountain directly below where the supply tubing comes
out of the bottom of the bottle filler (see sheet 4 of installation drawing). Check the
internal layout of your water cooler or drinking fountain prior to creating this
hole to assure that this is a feasible option. If it is not, punch the hole
wherever the internal layout mandates.
NOTE: It may be desirable to use a grommet (not supplied) in this hole in the water
cooler/fountain to protect against sharp edges.
NOTE: If it is not desirable to cut a hole in the water cooler/fountain, the supply
tubing could alternately be run through the back of the water cooler/fountain, up
through the wall, and out of the wall near the top of the bottle filler.
Shut off the water supply to the water cooler/fountain. Run the supply tubing off of
the water supply of the water cooler/fountain by means of a NSF-61 tee or saddle
valve (not supplied). This connection should be upstream of the dispense valve of
the water cooler/fountain and downstream of any filtration.
Step 3: Bottle Filler Height:
The bottle filler should be installed such that the center of the push button is 48” or
less from the floor*(see sheet 4 of installation drawing). If a front drain configuration
is used, it is recommended that the bottle filler be installed as low as possible so that
water draining into the water cooler/fountain bowl will not splash excessively.
Water coolers & fountains with back panels:
Some water coolers and fountains use a back panel that protrudes noticeably
from the wall. If this is the case, the sides of the bottle filler mounting frame
may be cut away to provide a 1/2”-deep relief to account for the back panel
(see “Drain Setup” in installation drawing). This allows the bottle filler to be
installed low over such water coolers and fountains.
*48” is the ADA maximum for wheelchairs for obstructed forward reach height. For ADA side reach
compliance, reduce this height to 46” or less (may not be possible with all water coolers or fountains).

04/17 Model 1900 Page 5 of 18
To do this, temporarily install the mounting frame to the bottle filler using the
supplied #8 x 1/2" flat head screws (qty. 4). Position the bottle filler over the
water cooler/fountain at the desired height (see sheet 4 of installation drawing
for installation dimensions at 48” reach height), and mark the mounting frame
on both sides where the top of the back panel ends. Cut the sides away at
these marks, taking care not to cut away the bottle filler mounting tabs as well
(see “Cutting the Mounting Frame Relief” in installation drawing).
Note the auxiliary mounting holes in the mounting frame for installation on
taller back panels (See “Mounting Frame & Optional Rear Drain Cutout
Details” in installation drawing).
Step 4: Bottle Filler Mounting:
Use the supplied (qty. 4 each) drywall anchors (1/4” pilot hole required), spacers,
and #10 x 2” screws (other fasteners, not supplied, may be needed, depending on
wall construction) to secure the bottle filler mounting frame to the wall at the desired
height (see “Mounting Frame & Optional Rear Cutout Details” in installation drawing
to install at 48” reach height), assuring the mounting frame is installed level.
Rear drain only:
Cut the opening in the wall for the drain, using the bottom of the mounting
frame as a reference point for the bottom of the cutout. Take care not to cut
below the bottom of the mounting frame, as this may be visible after
final installation. The cutout should be as wide as the bottom opening in the
mounting frame, and 2-1/2” high (see “Mounting Frame & Optional Rear
Cutout Details” in installation drawing).
Connect the inlet tubing to the push-in elbow in the bottle filler, if this hasn’t been
done already.
Mount the bottle filler to its frame with the supplied #8 x 1/2" flat head screws (qty. 4).
Rear drain only:
Connect the drain plumbing.
Step 5: Testing:
Turn on the water supply. Press the push button to dispense water; check both the
inlet plumbing and the drain for leaks.

04/17 Model 1900 Page 6 of 18
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1. Insufficient water flow. 1a. Check that any inlet screwdriver stop valve
(not supplied) is wide open. Turn
counterclockwise.
b. Verify minimum 30 psi flowing supply
pressure.
c. Clean strainer. See 5874 Series Valve
Manual.
d.
e.
Adjust valve to increase flow. Use front
adjust screw or see 5874 Series Valve
Manual.
Make sure nozzle is free of debris.
2. Excessive water flow. 2a. Adjust valve to decrease flow. Use front
adjust screw or see 5874 Series Valve
Manual.
3. Water flow is crooked or
splatters. 3a.
b.
c.
Make sure nozzle is free of debris.
Verify that bottle filler is installed level and
straight.
Adjust valve to decrease flow. Use front
adjust screw or see 5874 Series Valve
Manual.
4. Drain overflows. 4a. Check drain basin for obstructions.
5. Drain leaks at seal. 5a. Remove drain basin and reapply RTV seal.
For more information about Haws products, see our website: www.hawsco.com
© 2017 Haws®Corporation – All Rights Reserved
HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation.

04/17 Model 1900 Page 7 of 18

04/17 Model 1900 Page 8 of 18

04/17 Model 1900 Page 9 of 18

04/17 Model 1900 Page 10 of 18

04/17 Model 1900 Page 11 of 18

04/17 Model 1900 Page 12 of 18

04/17 Model 1900 Page 13 of 18

PARTS BREAKDOWN
APPROVED
DRAWN
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BYECN NO.
PAGE
DATE
DATE
ECN:
REVISED PER
CHKD
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
JL
2/10/14
4
0002076963
1900
BOTTLE FILLER, EWC RETROFIT
1:1
11
FV 07/06/17
4855
VWC
14 of 18
PARTS BREAKDOWN
5188
2017
JP
NOTES:
1 5874PB (ITEM 5) INCLUDES VRK5874 CARTRIDGE
ASSEMBLY (ITEM 6) AND PBA6 FLANGED PUSH
BUTTON (ITEM 7).
DRAIN, REVERSIBLE, 19002
3
PUSH BUTTON ASSY, NON-FLANGED
1
NOZZLE, REPLACEMENT
4DRAIN EXTENDER, 1900
5 BUTTON, PUSH, NON-FLANGED, PCP
6PBA7
0003707600
0002306901
5874PB
0002060018
ITEM DESCRIPTION PART NO.
FRAME, MOUNTING, 1900 0002546051
1
3
2
4
5
6
7
7REPAIR KIT, VALVE VRK5874
1
1
1

16 1/4"
[413<>mm]
8 5/16"
[211<>mm]
10"
[254<>mm]
(ALCOVE)
4"
[102<>mm]
1/4" QUICK
CONNECT
WATER INLET
8 3/8"
[213<>mm]
NOTES:
1. HOLD ROUGH-IN DIMENSIONS ±1/4" (6.4mm).
2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE ADHERED TO.
FOR INSTALLATION HEIGHTS OTHER THAN SHOWN, DIMENSIONS MARKED (*) MUST BE
ADJUSTED ACCORDINGLY. INSTALL A TRAP IN THE WASTE LINE AND A SCREWDRIVER STOP
IN THE SUPPLY LINE IF REQUIRED.
3 REFER TO 5874 SERIES OPERATION & MAINTENANCE MANUAL FOR PUSH BUTTON AND VALVE
INSTALLATION & MAINTENANCE INSTRUCTIONS.
4 BOTTLE FILLER IS SHOWN INSTALLED AT ADA MAXIMUM OBSTRUCTED FORWARD REACH HEIGHT.
FOR ADA OBSTRUCTED SIDE REACH COMPLIANCE, BOTTLE FILLER MUST BE LOWERED 2". ADA
COMPLIANCE DEPENDS ON OVERALL SIZE OF WATER COOLER OR DRINKING FOUNTAIN
(SEE SHEETS 3 & 4).
3
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
JL
2/10/14
4
0002076963.D
1900
BOTTLE FILLER, EWC RETROFIT
1:1
14
FV 07/06/17
4855
VWC
15 of 18
INSTALLATION
5188
2017
JP

MOUNTING FRAME
(SUPPLIED)
DRAIN BASIN
(SUPPLIED)
DRINKING
FOUNTAIN
(NOT
SUPPLIED)
DRAIN
EXTENDER
(SUPPLIED)
DRINKING FOUNTAIN BACK
PANEL (NOT SUPPLIED) WALL FACE
DRAIN SETUP
RUN A 1/8”-3/16” DIAMETER BEAD OF RTV RIGHT ALONGSIDE THE
GROOVE, BUT NOT IN THE GROOVE. CHECK THE RTV BEAD FOR
THIN SECTIONS, GAPS, OR AREAS WHERE THE BEAD DOES NOT
TOUCH THE PLASTIC - FILL THESE IN WITH RTV.
2 1/4"
[57mm]
(DRAIN)
3 13/16"
[97mm]
(IN-WALL
DEPTH)
WALL FACE
1-1/4" SLIP
JOINT WASTE
FITTING (NOT
SUPPLIED)
DRAIN BASIN
(REVERSED)
MOUNTING FRAME RELIEF CUT
DRAIN SEAL DETAIL
RTV SILICONE
(SUPPLIED)
(EXAMPLE ONLY; CUT HEIGHT MAY VARY)
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
JL 2/10/14
4
0002076963.D
1900
BOTTLE FILLER, EWC RETROFIT
1:1
24
FV 07/06/17
4855
VWC
16 of 18
INSTALLATION
5188
2017
JP

37"
[940mm]*
(HEIGHT TO
LOWER
MOUNTING
HOLES)
2 1/2"
[64mm]
CUTOUT
HEIGHT
C
L
4
#10 x 2"
SCREW
(SUPPLIED)
MOUNTING
FRAME
(SUPPLIED)
SPACER
(SUPPLIED)
ANCHOR
(SUPPLIED)
Ø1/4" HOLE
IN DRYWALL
WALL
FACE
IF A RELIEF MUST BE CUT
HIGHER THAN THE
MOUNTING TAB, CUT HERE
TO DETACH THE SIDE OF
THE MOUNTING FRAME
FROM THE MOUNTING TAB.
CUTTING THE MOUNTING FRAME RELIEF
MOUNTING FASTENER DETAIL
MOUNTING TAB
9"
[229mm]
MOUNTING FRAME & OPTIONAL
REAR DRAIN CUTOUT DETAILS
FLOOR LINE
WALL FACE
6 7/8"
[175mm]
CENTERLINE
MARKED WITH
GROOVES
REAR DRAIN
CUTOUT
(OPTIONAL) -
CUT TO SIDES
OF MTG FRAME
OPENING & TO
BOTTOM EDGE
OF MTG FRAME
AUXILIARY
MTG HOLES
4 1/2"
[114mm]
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
JL 2/10/14
4
0002076963.D
1900
BOTTLE FILLER, EWC RETROFIT
1:1
34
FV 07/06/17
4855
VWC
17 of 18
INSTALLATION
5188
2017
JP

48"
[1219mm]*
WALL FACE
DRINKING
FOUNTAIN
(NOT
SUPPLIED)
4
FLOOR LINE
1/4" O.D.
SUPPLY
TUBING
(SUPPLIED) 3"
LEFT OF
BOTTLE FILLER
CENTERLINE;
11/16" OUT
FROM WALL
TYPICAL DRINKING FOUNTAIN INSTALLATION
48"
[1219mm]*
WALL FACE
ELECTRIC
WATER
COOLER
(NOT
SUPPLIED)
4
FLOOR LINE
1/4" O.D.
SUPPLY
TUBING
(SUPPLIED) 3"
LEFT OF
BOTTLE FILLER
CENTERLINE;
11/16" OUT
FROM WALL
TYPICAL WATER COOLER INSTALLATION
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
JL
2/10/14
4
0002076963.D
1900
BOTTLE FILLER, EWC RETROFIT
1:1
44
FV
07/06/17
4855
VWC
18 of 18
INSTALLATION
5188
2017
JP