hayneedle Belham Living Carter 4-Drawer File Cabinet User manual

ITEM NAME:Belham Living Carter 4-Drawer File Cabinet
SKU: REDU165-1
For assistance with assembly, please contact customer service
1-888-880-4884
1/11

PRE-ASSEMBLY PREPARATION:
PARTS IDENTIFICATION:
!
DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE
RISK OF FINGER ENTRAPMENT
• Please read through these instructions before beginning assembly.
• Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all parts based on Parts List, extra room
will allow you to easily determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding
smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembled.
• Please check for any loose screws and tighten them before you use.
Bottom Frame (1) Qty:1 Qty:1 Qty:2Top Frame (2) Back Panel (3)
2/11
Left Side (4) Qty:1 Qty:1 Qty:1Centre Panel (5) Right Side (6)
Back Bar (7) Qty:2 Qty:1 Qty:1Left Front Bar (8) Right Front Bar (9)
Leg (10) Qty:4 Drawer Front (11) Qty:1 Qty:1Drawer Front (12)
Drawer Side (13) Qty:2 Drawer Side (14) Qty:2 Drawer Back (15) Qty:2
972mm
400mm
972mm
400mm
959mm
285.5mm
400mm
450mm
450mm
400mm
450mm
400mm
462mm
38mm
462mm
38mm
462mm
38mm
160mm
457mm
151mm
457mm
151mm
116mm
352mm
352mm
116mm
411mm
113mm

3/11
HARDWARE LIST:
Bolt (A) Qty:8 Qty:8 Qty:8Spring Washer (B) Flat Washer (C)
Allen Key (D) Qty:1 Qty:32 Qty:16Screw (E) Cam Lock (F)
Cam Pin (G) Qty:16
1/4"x1-1/4"mm
8 x 25mm
7x12mm
340x10x2mm
1/4x16"mm
M4
#9x12mm
Ø3/16×1-1/2"
Qty:32Bolt (H) Qty:32Nut (I)
Qty:2Screw (L)
Wooden Dowel (J) Qty: 24 Metal Bar (K) Qty:4
Qty:2Wall Plug (O)
Screw (M) Qty: 2 Plastic Rope (N) Qty:2
Qty:32Nut (I)
Bracket (P) Qty: 4 Metal Bar (K) Qty:4
Phillips Screwdriver
(not provided)
423mm
338mm
Drawer Bottom (16) Qty:4 Qty:1 Qty:1Drawer Front (17) Drawer Front (18)
Drawer Side (19) Qty:2 Qty:2 Qty:1Drawer Side (20) Drawer Back (21)
Drawer Back (22) Qty:1 Qty:2 Qty:2Drawer Bottom (8) Drawer Back (9)
457mm
321mm
457mm
321mm
352mm
255mm
352mm
255mm
Ø8x30mm
411mm
252mm
411mm
252mm

STEP-BY-STEP ASSEMBLY:
1
STEP 1:
Assemble Legs (10) to Bottom Frame (1) using Bolts (A) with Spring
Washers (C) and Flat Washers (B), then tighten with Allen Key (D).
2
STEP 2:
Insert Cam Pins (F) to Top Frame (2), Side Panels (4,6) and Bottom Frame (1).
4/11
DETAIL STEP PLE
ASE SEE THE BELOW
PICTURE.
(1) Insert Too Low Insert Too Deep
The Correct Positon
A
C
B
D
F
F
1
1
1
10
10
10
10
10
2
4
6

STEP-BY-STEP ASSEMBLY:
3
STEP 3:
●Insert Wooden Dowels (J) to Bottom Frame (1) and Bars (7,8).
●Attach Left Side (4) to Bottom Frame (1) using Wooden Dowels (J) and Cam Locks (G).
●Attach Bars (7,8) to Left Side (4) using Wooden Dowels (J) and Cam Locks (G).
Note: Tighten Cam Locks with an across headed screwdriver (not supplied),
see details as below.
4
STEP4:
●Insert Wooden Dowels (J) and Cam Pins (F) to Bottom Frame (1) and Bars (7,8).
●Attach Centre Panel (5) to Bottom Frame (1) using Wooden Dowels (J) and Cam Locks (G).
●Attach Bars (7,8) to Centre Panel (5) using Wooden Dowels (J) and Cam Locks (G).
Note: Tighten Cam Locks with an across headed screwdriver (not supplied), see
details as below.
5/11
DETAIL STEP PLEASE SEE THE BELOW PICTURE.
(2) (3) (4)
F
DETAIL STEP PLEASE SEE THE BELOW PICTURE.
(2) (3) (4)
F
GG
G
G
J
J
J
J
1
1
7
7
7
8
88
4
5
5
5

STEP-BY-STEP ASSEMBLY:
5
STEP 5:
Insert Wooden Dowels (J) to Bars (7,9) and attach Bars (7,9) to Centre Panel (5) using Cam
Lock (G).
Note: Tighten Cam Lock with an across headed screwdriver (not supplied), see details
as below.
6
STEP 6:
●Attach Right Side (6) to Bottom Frame (1) using
Wooden Dowels (J) and Cam Locks (G).
●Attach Bars (7,9) to Right Side (6) using Wooden
Dowels (J) and Cam Locks (G).
Note: Tighten Cam Locks with an
across headed screwdriver (not supplied),
see details as below.
Insert Wooden Dowels (J) to
Bottom Frame (1) and Bars (7,9).
6/11
DETAIL STEP PLEASE SEE THE BELOW PICTURE.
(2) (3) (4)
DETAIL STEP PLEASE SEE THE BELOW PICTURE.
(2) (3) (4)
F
G
G
G
G
J
J
J
J
1
1
7
7
7
5
5
5
9
99
9
6
6
6
J

STEP-BY-STEP ASSEMBLY:
8
STEP 8:
Place Back Panels (3) to the assembled unit back and fix Screws (E).
7
STEP 7:
●Insert Wooden Dowels (J) to Left Side (4), Right Side (6) and Centre Panel (5).
●Attach Top Frame (2) to Left Side (4), Right Side (6) and Centre Panel (5) using Wooden
Dowels (J) and Cam Locks (G).
Note: Tighten Cam Locks with an across headed screwdriver (not supplied), see details
as below.
DETAIL STEP PLEASE SEE THE BELOW PICTURE.
(2) (3) (4)
F
7/11
G
J
E
4
5
66
22
3
3

STEP-BY-STEP ASSEMBLY:
9
STEP 9:
●Attach Drawer Sides (13,14) to Drawer Front (11) using Bolts (H) and Nuts (i).
●Insert Drawer Bottom (16) to Drawer Sides aligning the pre-drilled grooves.
●Attach Drawer Back (15) to Drawer Sides using Bolts (H) and Nuts (I).
Note: Tighten Bolts with an across headed screwdriver (not supplied), see details as
below.
10
STEP 10:
●Attach Drawer Sides (13,14) to Drawer Front (12) using Bolts (H) and Nuts (i).
●Insert Drawer Bottom (16) to Drawer Sides aligning the pre-drilled grooves.
●Attach Drawer Back (15) to Drawer Sides using Bolts (H) and Nuts (I).
8/11
H
H
H
H
I
I
I
I
11
11
12
12
13
14
14
13
13
15
15
16
16
14
14
13
13
14
14
13
Left Drawer
Right Drawer

STEP-BY-STEP ASSEMBLY:
11
STEP 11:
●Attach Drawer Sides (19,20) to Drawer Front (17) using Bolts (H) and Nuts (i).
●Insert Drawer Bottom (16) to Drawer Sides aligning the pre-drilled grooves.
●Attach Drawer Back (21) to Drawer Sides using Bolts (H) and Nuts (I).
Note: Tighten Bolts with an across headed screwdriver (not supplied), see details as
below.
12
STEP 12:
●Attach Drawer Sides (19,20) to Drawer Front (18) using Bolts (H) and Nuts (i).
●Insert Drawer Bottom (18) to Drawer Sides aligning the pre-drilled grooves.
●Attach Drawer Back (22) to Drawer Sides using Bolts (H) and Nuts (I).
Note: Tighten Bolts with an across headed screwdriver (not supplied),
see details as below.
9/11
H
I
H
I
H
I
H
I
17
17
18
19
19
19
19
19
19
20
20
20
20
20
20
16
16
21
22
Left Drawer
Right Drawer
K
K
K
K

STEP-BY-STEP ASSEMBLY:
13
STEP 13:
Insert Drawers to the assembled cabinet.
10/11
Move the ball runner to front before put in the drawers.
14
STEP 14:
●Fix two Brackets (P) to the back top of the unit using Screws (M).
●Use electric drill to drill two small holes on the desired location of wall, insert Wall Plugs (O)
into the holes by rubber mallet, use Screws (L) to attach the Brackets (P) onto wall.
●Then use Plastic Ropes (N) to link the product and wall together as shown.
Note: This is an option step. For safety, the tilting prevent hardware should be used
as a part of assembly.
Wall
M
P
P
LN
O

11/11
MAINTENANCE AND CARE TIPS FOR WOOD FURNITURE:
-Always dust, wipe and clean in the direction of the wood grains.
-Check and re-tighten screws/blots after the product has been used for a period of time.
-It is best to keep your furniture in a climate controlled environment. Extreme temperature and humidity changes can
-Heat creates chemical changes in the furniture finish. As a result, whitish spots may appear.