hayneedle SBP001-1/2 User manual

1.888.880.4884
Assembly Instructions
Item Number: SBP001-1/2
Product Name: Family Dinner Table Set with Metal Legs
PRE-ASSEMBLY PREPARATION:
Please check all contents of this package before attempting to assemble the product. A full checklist of
components is provided. If any components are missing, please contact our customer service number
above.
Read the Assembly Instructions in full before you begin to assemble.
Please use CAUTION AND CARE WHEN LIFTING the product to avoid personal injury and (or) damage
to the product.
Two people are recommended to assemble this product.
A power Philips screwdriver is recommended for attaching the table tops and cushions.
Assemble this product on a flat, soft surface.
The hardware packet contains SMALL ITEMS which should be KEPT AWAY FROM CHILDREN.
Periodically check and ensure that all bolts are fully tightened.
1 – CORNER BENCH UNIT
Parts and Fittings Identification:
Note: Code labels are pasted on the metal parts for easy identification.
CODE PARTS QTY CODE FITTINGS QTY
A11PC 1 45mm 8PCS
B11PC 2 35mm 5PCS
C11PC 3 30mm 6PCS
4 12mm 23PCS
D11PC 5 40PCS
6 1PC
E11PC 7 4PCS
8 1PC
F11PC 9 1PC
1

Parts Identification (cont.):
CODE PARTS QTY CODE PARTS QTY
G12PCS Q1 1PC
H11PC R1 1PC
I11PC S1 1PC
J11PC T1 1PC
K11PC U1 1PC
L11PC V1 1PC
M11PC W1 1PC
N11PC X1 2PCS
O11PC Y1 1PC
P11PC Z1 2PCS
Additional Tools Required:
Philips Screwdriver or Power Screwdriver
2

Step By Step Assembly Instructions
Step 1: LONG BENCH
Attach the long back frame (O1) to legs (I1and J1) and secure with bolts (4) using allen key (9).
Do not fully tighten bolts yet.
Attach the long seat frame (Q1) to leg (I1) and secure with bolts (1) and washer (7), then attach
it to leg (J1) and secure with bolts (1). Do not fully tighten bolts yet.
Note: Make sure the metal tabs on the back and seat frames (O1 and Q1) are positioned
correctly as shown.
After all bolts are positioned, fully tighten bolts using allen key (9).
3

Step 2: LONG BENCH
Attach the middle leg (N1) to seat frame (Q1) and secure with bolts (3) using allen key (9).
Attach the short front rails (Z1) to legs (I1, N1 and J1) and secure with bolts (4) using allen key
(9).
Attach the short stretchers (X1) to middle leg (N1) and secure with bolt (6).
Attach the short stretchers (X1) to legs (I1 and J1) and secure with bolts (3) using allen key (9).
4

Step 3: SHORT BENCH
Attach the short back frame (P1) to legs (K1and L1) and secure with bolts (4) using allen key (9).
Do not fully tighten bolts yet.
Attach the short seat frame (R1) to leg (L1) and secure with bolts (1) and washer (7), then attach
it to leg (K1) and secure with bolts (1) using allen key (9). Do not fully tighten bolts yet.
Attach the long front rail (Y1) to legs (K1and L1) and secure with bolts (4) using allen key (9). Do
not fully tighten bolts yet.
Attach the long stretcher (W1) to legs (K1and L1) and secure with bolts (3) using allen key (9).
Do not fully tighten bolts yet.
Note: Make sure the metal tabs on the back and seat frames (P1 and R1) are positioned
correctly as shown.
After all bolts are positioned, fully tighten bolts using allen key (9).
5

Step 4: CORNER BENCH
Attach the corner seat frame (M1) to the assembled benches as shown and secure with bolts (2)
using allen key (9).
Attach the corner back frames (V1 and U1) to the assembled benches as shown and secure with
bolts (4) using allen key (9).
Attach the corner back rail (H1) to the assembled benches as shown and secure with bolts (4)
using allen key (9).
6

Step 5: BACK CUSHIONS
Note: Firstly position all seat cushions (A1, B1, C1) and backrest cushions (D1, E1, F1, G1) in place
as shown and make sure to leave no gap between the seat and back cushions.
Then secure the backrest cushions (D1, E1, F1 and G1) to back frames (O1, P1 and H1) and seat
frames (Q1, R1 and M1) with screw (5) using Philips screwdriver. (Power screwdriver
recommended).
7

Step 6: SEAT CUSHIONS
Carefully position the corner bench sideways as shown and attach the seat cushions (A1, B1
and C1) to seat frames (Q1, R1 and M1) and secure with screw (5) using Philips screwdriver.
(Power screwdriver recommended).
Note: Metal tabs to connect frame to cushion may have shifted slightly in transit. They can
simply be pressed down to the needed level position to allow the screws to securely enter the
cushion.
8

Step7: CORNER SHELF AND LEG
Attach the corner shelf (T1) to corner back frame (U1) and secure with bolt (2) and washer (8)
using allen key (9).
Attach the corner leg (S1) to corner shelf (T1) and secure with bolts (4) using allen key (9).
Attach the corner shelf (T1) to corner back rail (H1) and secure with screws (5) using Philips
screwdriver. (Power screwdriver recommended).
9

Step 8:
Assembly for corner bench is complete.
10

2 – TABLE
Parts and Fittings Identification:
CODE PARTS QTY CODE FITTINGS QTY
A21PC 4
12mm 16PCS
B24PCS 5 10PCS
C22PCS
D22PCS
11

Step By Step Assembly Instructions
Step 1: TABLE LEGS
Attach the side rails (C2and D2) to legs (B2) and secure with bolt (4) using allen key (6).
12

Step 2: TABLE TOP
Place the table top (A2) upside down on a protected surface. Position the assembled table
frame on the table top as shown and secure with screws (5) using a Philips screwdriver. (Power
screwdriver recommended).
*Note: Metal tabs to connect the table frame to the table top may have shifted slightly in transit.
They can simply be pressed down to the needed level position to allow the screws to securely
enter the table top.
13

Step 3: TABLE
Carefully turn over the unit and assembly for the table is complete.
14

3 – BENCH
Parts and Fittings Identification:
CODE PARTS QTY CODE FITTINGS QTY
A31PC 1
45mm 4PCS
B31PC 3
30mm 2PCS
C32PC 4
12mm 4PCS
D31PC 5 4PCS
E32PCS 7 4PCS
15

Step By Step Assembly Instructions
Step 1: FRAME
Attach the seat frame (B3) to legs (C3) and secure with bolts (1) and washer (7) using allen key
(6).
Attach the side rails (E3) to legs (C3) and secure with bolts (4) using allen key (6).
Attach the stretcher (D3) to legs (C3) and secure with bolts (3) using allen key (6).
16

Step 2: CUSHION
Place the seat cushion (A3) upside down on a protected surface. Position the assembled bench
frame on the cushion as shown and secure with screws (5) using a Philips screwdriver. (Power
screwdriver recommended).
17

Step 3: BENCH
Carefully turn over the bench and assembly is complete.
18