Riverside Furniture Cordero 15630 User manual

Components and Hardware List
Riverside
FURNITURE
email: [email protected]
Page 1 of 4
Made in Viet Nam
A
Cordero
Corner Desk
Assembly Instructions
G
1 pc. 3 pcs.1 pc. BC
H
2 pcs. 8 pcs.
5
16" Flat Washer
J
1 pc.
16 pcs. K16 pcs.
M22 pcs. N
1
4" Spring Washer 1
4" Flat Washer
16 pcs. O16 pcs. P
4mm Allen Key
1 pc.
PLM
J
2 pcs.
F
A
B
C
5
16" x 50mm (2" Lg.)
Allen Head Bolt
I6 pcs.
L Bracket
Middle Desk Top Left Desk Top Right Desk Top Leg Frame
Short Stretcher Long Stretcher
L
Besuretocheckallpackingmaterialcarefullyforsmallparts,whichmayhavecomelooseinsidethecartonduring
shipment.Separate,countandcheckallpartsagainstthePartsListandHardwareListabove. Failuretousethecorrectlength
boltsintheproperlocationsmayresultinanunsafeproductandcouldalsocausedamagetothepartsbeingassembled.
Step 1. Place the Writing Desk Top (A, B,C) face down side by side on a clean and soft surface.
Step 2. Attach the Left, Right Desk Top (B, C) to the Middle Desk Top (A) by using the 32mm long Allen Head Bolts
(J), Spring Washer (L) and Flat washer (M), tighten with the 4mm Allen Key (P) as shown.
To remove the drawer if it ever becomes necessary:
A. Pull the drawer fully open so the black latch is visible in the
inside channel of the guides.
B. Release the latches by simultaneously pushing left side lever up
and the right side down.
C. At the same time, pulling the drawer forward until the slides
release.
To reinstall the drawers, carefully align the channels of the guide
and push drawer back into cabinet. Open and close drawer fully
a couple times to verify proper operation.
15630
5
16" x 32mm
(1-1/4" Lg.)
Allen Head Bolt
1
4" x 25mm
(1" Lg.)
Allen Head Bolt
5
16" Spring
Washer
22 pcs.
Leg
E1,2,3
DL,R 1 pc. Left
1 pc. Right

Riverside
FURNITURE
email: [email protected]
Page 2 of 4
Made in Viet Nam
Cordero
Corner Desk
Assembly Instructions
A
B
C
DL
DR
Step 3. Attach he Left and Right Leg Frames (DR,L) to the Left, Right Desk Top (B, C) by using the 32mm long Allen
Head Bolt (J), Spring Washer (L) and Flat washer (M), tighten with the 4mm Allen Key (P) as shown.
DL
DR
E2
E3 E1
A
CB
P
I
L
M
P
J
L
M
Step 4. Attach the three Legs (E1,2,3) to the Middle Desk Top (A) by using the 50mm long Allen Head Bolts (I), Spring
Washer (L) and Flat washer (M), tighten with the 4mm Allen Key (P) as shown.

Riverside
FURNITURE
email: [email protected]
Page 3 of 4
Made in Viet Nam
Cordero
Corner Desk
Assembly Instructions
PKN
O
A
C
B
H
H
H
O
N
K
P
G
G
FF
H
G
G
Step 5. Assemble the L-Brackets (H) to the Legs (E1,2,3) and Leg Frames (DR,L) as shown, by using the 1 4" x 25
mm Allen Head Bolts (K), Spring Washers (N) and Flat Washers (O). Tighten with the 4mm Allen Key (P) as
shown.
Step 6. Position and connect one Short Stretcher (F) between one Leg Frame and Leg using the 1 4" x 25mm Allen
Head Bolts (K), Spring Washers (N) and Flat Washers (O). Tighten with the 4mm Allen Key(P).
Step 7. Repeat the assembly for the other Short Stretcher and both Long Stretchers (G).
E1
DR DL
E1
E2
E3

Riverside
FURNITURE
email: [email protected]
Page 4 of 4
Made in Viet Nam
Cordero
Corner Desk
Assembly Instructions
Leveler
Using two people and to prevent unnecessary stress on the Desk, carefully set the assembled Desk upright and
move to the desired location in the room.
If the three sections are not flush on the top surfaces, reach underneath the desk, loosen the Bolts, adjust the
sections to be flush and retighten the Bolts.
There are levelers installed in the
bottom of the Leg which can be
adjusted to compensate for uneven
flooring, if needed.