hayneedle Mid Century Modern Finn Hall Tree REDU134-1 User manual

ITEM NAME:Mid Century Modern Finn Hall Tree
SKU: REDU134-1; REDU134-2
For assistance with assembly, please contact customer service
1-888-880-4884
1/10

PRE-ASSEMBLY PREPARATION:
PANEL AND FITTINGS IDENTIFICATION:
!
DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE
RISK OF FINGER ENTRAPMENT
• Please read through these instructions before beginning assembly.
• Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all parts based on Parts List, extra room
will allow you to easily determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding
smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembled.
• Please check for any loose screws and tighten them before you use.
Cabinet (1) Qty:1 Qty:4 Qty:1Leg (2) Left Side (3)
2/10
Right Side (4) Qty:1 Qty:1 Qty:1Back Frame (5) Shelf (6)
Top Bar (7) Qty:1
HARDWARE LIST:
Bolt (A) Qty:8 Qty:15Bolt (B) Qty:5Bolt (C)
Spring Washer (D) Qty:28 Qty:28Flat Washer (E) Qty:1Allen Key (F)
868mm
400mm
220mm
1670mm
360mm
1670mm
360mm
868mm
350mm
868MM
250MM
868mm
45mm
1/4"×2-1/4" 1/4"×1-1/4"
1/4"×16mm
1/4"×1"

STEP-BY-STEP ASSEMBLY:
1
STEP 1:
Take out drawer to start Assembly.
3/10
Bracket (J) Qty:5 Qty:2 Qty:2Screw (K) Screw (L)
Plastic Rope (M) Qty:2 Qty:2 Qty:4Wall Plug (N) Wall Bracket (O)
Cam Pin (H) Qty:2 Qty:2Cam Lock (I)
Qty:12Wooden Dowel (G)
Ø8x30mm
8x25mm
7x12mm
Phillips Screwdriver
(not provided)
Move the plastic insert
up to release drawers.
02
01 1
35mm
51mm
Ø15mm
Move the plastic insert
down to release drawers.

STEP-BY-STEP ASSEMBLY:
2
STEP 2:
Attach Legs (2) to Cabinet (1) using Bolts (A) with Spring Washers (D) and Flat Washers
(E), then tighten with Allen Key (F).
3
STEP 3:
Insert Cam Pins (H) into pre-drilled holes of Left Side (3) and Right Side (4).
4/10
DETAIL STEP PLEASE SEE THE
BELOW PICTURE.
(1) (2) Insert Too Low Insert Too Deep
The Correct Positon
1
1
2
2
2
2
2
3
4
A
DE
F
H
H

STEP-BY-STEP ASSEMBLY:
4
STEP 4:
Attach Left Side (3) to Cabinet (1) using Bolts (B) with Spring Washers (D) and Flat Washers
(E), then tighten with Allen Key (F).
5
STEP 5:
Fix Bracket (J) to Back Frame (5) using Bolts (C) with Spring Washers (D) and Flat Washers
(E), then tighten with Allen Key (F).
5/10
1
1
3
5
C
J
ED
B
D
E

7
STEP 7:
• Insert Wooden Dowels (G) to Left Frame (3).
• Attach Back Frame (5) and Shelf (6) to Left Frame (3)
using Bolts (B) with Spring Washers (D) and Flat
Washers (E), then tighten with Allen Key (F).
• Attach Top Bar (7) to Left Frame (3) using Cam Locks
(I), tighten with Phillips Screwdriver (not provided).
STEP-BY-STEP ASSEMBLY:
6
STEP 6:
Attach Back Frame (5) to Shelf (6) using Bolts (B) with Spring Washers (D) and Flat Washers
(E), then tighten with Allen Key (F).
6/10
DETAIL STEP PLEASE SEE THE
BELOW PICTURE.
(3) (4)
3
3
3
5
5
5
6
6
6
7
7
B
D
E
G
G
GG
B
D
E
I

9
STEP 9:
Fix Bolts (B) with Spring Washers (D) and Flat Washers (E) from inside of the Cabinet (1) to
Right Fame (4), tighten with Allen Key (F).
STEP-BY-STEP ASSEMBLY:
8
STEP 8:
• Insert Wooden Dowels (G) to Back Frame (5) , Shelf (6) and Top Bar (7).
• Attach Right Frame (4) the assembled shelf and bar using Bolts (B) with Spring Washers (D)
and Flat Washers (E) and Cam Locks (I), then tighten with Allen Key (F) and Phillips
Screwdriver (not provided).
7/10
1
5
5
6
6
7
7
4
4
4
GG
G
D
E
B
D
E
B
I
DETAIL STEP PLEASE SEE THE
BELOW PICTURE.
(3) (4)

STEP-BY-STEP ASSEMBLY:
10
STEP 10:
Insert the Drawer into the cabinet.
8/10
The zinc iron track
slips to the front

STEP-BY-STEP ASSEMBLY:
11
STEP 11:
●Fix two Wall Brackets (O) to the top rail using Screws (L).
●Use electric drill to drill two small holes on the desired location of wall, insert Wall Plugs (N)
into the holes by rubber mallet, use Screws (K) to attach the Wall Brackets (O) onto wall.
●Then use Plastic Ropes (M) to link the product and wall together as shown.
Note: This is an option step. For safety, the tilting prevent hardware should be used
as a part of assembly.
9/10
Wall
K
O
O
M
L
N

MAINTENANCE AND CARE TIPS FOR WOOD FURNITURE:
-Always dust, wipe and clean in the direction of the wood grains.
-Check and re-tighten screws/blots after the product has been used for a period of time.
-It is best to keep your furniture in a climate controlled environment. Extreme temperature and humidity changes can
-Heat creates chemical changes in the furniture finish. As a result, whitish spots may appear.
10/10