hayneedle Belham Living Carter Mid Century Modern Coffee Table... User manual

ITEM NAME:Belham Living Carter Mid Century Modern Coffee Table
SKU: REDU037-1
For assistance with assembly, please contact customer service
1-888-880-4884
1/6

PRE-ASSEMBLY PREPARATION:
PANEL AND FITTINGS IDENTIFICATION:
!
DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE
RISK OF FINGER ENTRAPMENT
• Please read through these instructions before beginning assembly.
• Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all parts based on Parts List, extra room
will allow you to easily determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding
smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembled.
• Please check for any loose screws and tighten them before you use.
Bottom Frame (1) Qty:1 Qty:1 Qty:1Top Frame (2) Left Runner Board (3)
2/6
Right Runner Board (4) Qty:1 Qty:1 Qty:1Left Side (5) Right Side (6)
Drawer Bottom (7) Qty:2 Qty:2 Qty:2Drawer Back (8) Drawer Right (9)
Drawer Left (10) Qty:2 Drawer Front (11) Qty:2 Qty:4Leg (12)
1198mm
600mm
1200mm
600mm
600mm
128mm
600mm
128mm
600mm
80mm
600mm
80mm
465mm
277mm
456mm
100mm
280mm
100mm
280mm
100mm
495mm
125mm
305mm

STEP-BY-STEP ASSEMBLY:
1
STEP 1:
●Insert the Nuts (I) to Drawer Front (11) and attach the Drawer Sides (09 and 10) to Drawer
Front (11), then using the Bolt (H) lock them together, see details as below.
●Insert the Drawer Bottom (07) into the grooves of Drawer Sides and Drawer Front.
HARDWARE LIST:
3/6
8:ytQ8:ytQ8:ytQ)A(tloB Spring Washer (B) Flat Washer (C)
61:ytQ61:ytQ1:ytQ)D(yeKnellA Wooden Dowel (E) Cam Lock (F)
Cam Pin (G) Qty:16
1/4x44mm 1/4x13mm 1/4x17mm
4M
Ø8x30mm
x 2
Qty:16 61:ytQ)H(tloB Nut (I)
Phillips Screwdriver
(not provided)
H
HH
I
I
I
I
09
10
09
10
11
07

STEP-BY-STEP ASSEMBLY:
2
STEP 2:
Insert the Nuts (I) to Drawer Back (08) and attach the Drawer Back to Drawer Sides,
then using the Bolts (H) lock them together, see details as below.
Note: Tighten Cam Locks with an across headed screwdriver (not supplied),
see details as below.
3
STEP 3:
Fix the Legs (12) to Bottom Frame (01) using Bolts (A) with Spring Washers (B) and Flat
Washers (C), then tighten with Allen Key (D).
4/6
12
12
12
12
12
01
01
ABC
D
x 2
H
H
H
H
08
10
09
I
I
I
I

STEP-BY-STEP ASSEMBLY:
4
STEP 4:
Turn over the Bottom Frame with legs. Insert Cam Pins (G) and Wooden Dowels (E) into the
Bottom Frame, then attach Left Side (05), Right Side (06), Left Runner Board (03) and Right
Runner Board (04) to the Bottom Frame locking
with Cam Locks (F).
Note: Tighten Cam Locks with an
across headed screwdriver
(not supplied), see details as
below.
5
STEP 5:
Insert Cam Pins (G) to the Top Frame (02) and Insert the Wooden Dowels (E) to the
pre-assembled boards,
see details as below. Attach the Top Frame to the pre-assembled
unit using Cam Locks (F).
Note: Tighten Cam Locks with an across headed
screwdriver (not supplied), see details as below.
5/6
E
E
E
E
E
E
E
E
E
G
G
G
G
G
G
G
G
G
G
G
G
G
F
F
F
FF
F
F
FF
F
F
F
F
05
03
04
06
02
E
E
E
E
DETAIL STEP PLEASE SEE THE BELOW PICTURE.
(1) (2) (3) (4)
G
F
DETAIL STEP PLEASE SEE THE BELOW PICTURE.
(1) (2) (3) (4)
G
F
Insert Too Low Insert Too Deep The Correct Positon
Insert Too Low Insert Too Deep The Correct Positon

MAINTENANCE AND CARE TIPS FOR WOOD FURNITURE:
-Always dust, wipe and clean in the direction of the wood grains.
-Check and re-tighten screws/blots after the product has been used for a period of time.
-It is best to keep your furniture in a climate controlled environment. Extreme temperature and humidity changes can
-Heat creates chemical changes in the furniture finish. As a result, whitish spots may appear.
STEP-BY-STEP ASSEMBLY:
6
STEP 6:
Insert the drawers into the assembled unit, see details as below.
6/6