Hdav HD-C5S4P User manual

HDMI Extender over Single CAT
with Bi-
directional IR, RS
Auto EDID Learning
HDMI Extender over Single CAT
X
directional IR, RS
-232
Serial
Auto EDID Learning
User Manual
(HD-C5S4P)
HDMI Extender over Single CAT
X
Serial
, and
rev: 120403

Safet
The HD-C5S4P
HDMI extender over single cat.X with bi
learning
has been tested for conformance to safety regulations and requirements, and has been certified
for international use. However, like all e
Please read and follow the safety instructions to protect yourself from possible injury and to minimize the
risk of damage to the unit.
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where explained in this manual.
Provide proper ventilation and air circulation and do not use near water.
Keep objects that might damage the device and assure that the placement of this unit is on
surface.
Use only the power adapter and power cords and connection cables designed for this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.
TABLE OF CONTENTS
INTRODUCTION
................................
FEATURES ................................
................................
SPECIFICATIONS
................................
PANEL DESCRIPTIONS
................................
Transmitting unit ► HD-
C5S4P
Receiving unit ► HD-
C5S4P
PACKAGE CONTENTS
................................
CONNECTION DIAGRAM
................................
IR PASS-THROUGH
................................
HARDWARE INSTALLATION
................................
PIN DEFINITION
................................
NOTICE ................................
................................
WARRANTY ................................
................................
Safet
y and Notice
HDMI extender over single cat.X with bi
-directional IR RS-
232 and Auto EDID
has been tested for conformance to safety regulations and requirements, and has been certified
for international use. However, like all e
lectronic equipments, the HD-C5S4P
should be used with care.
Please read and follow the safety instructions to protect yourself from possible injury and to minimize the
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where explained in this manual.
Provide proper ventilation and air circulation and do not use near water.
Keep objects that might damage the device and assure that the placement of this unit is on
Use only the power adapter and power cords and connection cables designed for this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
................................
................................................................
................
................................
................................
........................
................................
................................................................
..............
................................
................................
................................
C5S4P
-TX ................................
................................
C5S4P
-RX ................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
............................
................................
................................................................
................
................................
................................
............................
................................
................................
.....................
232 and Auto EDID
has been tested for conformance to safety regulations and requirements, and has been certified
should be used with care.
Please read and follow the safety instructions to protect yourself from possible injury and to minimize the
Keep objects that might damage the device and assure that the placement of this unit is on
a stable
Use only the power adapter and power cords and connection cables designed for this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
................
1
........................
1
..............
2
................................
.... 3
................................
......... 3
................................
............ 4
................................
...... 6
................................
.. 6
................................
.......... 7
............................
8
................
9
............................
10
.....................
11

INTR
The HD-C5S4P
HDMI extender over single cat.X with bi
Learning
boosts up your video/audio transmission distance up to 60m (200ft) in HDTV 1080i format, 40m
(130ft) in HDTV 1080p format, and 20m (65ft) in HDTV 1080p with 36
supports the most advanced 3D video format and therefore guarant
the market. With only one cost effective Cat.5/5e/6 cable, users can readily extend HDTV sources from DVD
players, Blu-
ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant display
monitors including HDMI or DVI enabled TV sets or LCD PC monitors. With the advanced design for the latest
HDMI technology, deep color video, DTS
compatibility are all further insured. This flex
high quality video and audio with a greater distance at the minimal cost, when integrating several components
apart. In addition, HD-C5S4P
is also equipped with bi
control. These
bonus feature allows users to boost IR control distance up to 100m (330 ft) and makes IR
control possible through only single Cat.5/5e/6 cable including HDMI signals.
convenient
path for interactive application, such as touch panels.
The HD-C5S4P
includes two units: transmitting unit
transmitting unit is used to capture the input HDMI / DVI signals with IR control packets and carry
via one cost effective Cat.5/5e/6 cable. The receiving unit is responsible for equalizing the transmitted HDMI
signal and reconstructing IR
and serial control
receiving units can be up
to 60m (200ft) at HD 720p or 1080i; or 40m (130ft) at Full HD 1080p. With an 8
equalization rotary control on the receiving unit, users can adjust the equalization strength to the received
HDMI signals accordingly, and therefore optimize the transmis
FEATURES
Support HDMI Deep Color & full 3D
Extends the transmission up to 60m (200ft) from the HDMI source at HD 1080i or 720p 24
Extends
the transmission up to 40m (130ft) from the HDMI source at Full HD 1080p 24
Extends the transmission up to 20m (65ft) from the HDMI source at Full HD 1080p 36
HDCP 1.1 compliant
Auto EDID feature
Minimizes
the cable skew by adjustable 8
Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6 cable transmission
DTS-
HD and Dolby TrueHD high bit rate audio support
Supports full frequency IR signal from 20KHz to 60KHz
Bi-directional IR path
Full Duplex RS-
232 control up to 115,200 bps through connector
Allows cascading
Wall mounting housing design for easy and robust installation
Perfectly integrated with other HDMI over CAT5 series products
The claimed transmission
distance
device and display.
For over CAT5/COAX
transmission,
jack along the transmission
INTR
ODUCTION
HDMI extender over single cat.X with bi
-directional IR RS-
232 and Auto EDID
boosts up your video/audio transmission distance up to 60m (200ft) in HDTV 1080i format, 40m
(130ft) in HDTV 1080p format, and 20m (65ft) in HDTV 1080p with 36
-
bit color depth.
supports the most advanced 3D video format and therefore guarant
ees the highest 3D video compatibility on
the market. With only one cost effective Cat.5/5e/6 cable, users can readily extend HDTV sources from DVD
ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant display
monitors including HDMI or DVI enabled TV sets or LCD PC monitors. With the advanced design for the latest
HDMI technology, deep color video, DTS
-
HD Master Audio or Dolby TrueHD audio, and HDCP supports and
compatibility are all further insured. This flex
ibility makes HDCP compliant DVD players or PS3 transmit utmost
high quality video and audio with a greater distance at the minimal cost, when integrating several components
is also equipped with bi
-directional IR pass-through path
and RS
bonus feature allows users to boost IR control distance up to 100m (330 ft) and makes IR
control possible through only single Cat.5/5e/6 cable including HDMI signals.
In addition, serial port offers the
path for interactive application, such as touch panels.
includes two units: transmitting unit
HD-C5S4P-TX
and receiving unit
transmitting unit is used to capture the input HDMI / DVI signals with IR control packets and carry
via one cost effective Cat.5/5e/6 cable. The receiving unit is responsible for equalizing the transmitted HDMI
and serial control
signals. The transmission distance between the sending and
to 60m (200ft) at HD 720p or 1080i; or 40m (130ft) at Full HD 1080p. With an 8
equalization rotary control on the receiving unit, users can adjust the equalization strength to the received
HDMI signals accordingly, and therefore optimize the transmis
sion distance between source and destination.
FEATURES
Extends the transmission up to 60m (200ft) from the HDMI source at HD 1080i or 720p 24
the transmission up to 40m (130ft) from the HDMI source at Full HD 1080p 24
-
Extends the transmission up to 20m (65ft) from the HDMI source at Full HD 1080p 36
-
bit
the cable skew by adjustable 8
-level equalization control
Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6 cable transmission
HD and Dolby TrueHD high bit rate audio support
Supports full frequency IR signal from 20KHz to 60KHz
232 control up to 115,200 bps through connector
Wall mounting housing design for easy and robust installation
Perfectly integrated with other HDMI over CAT5 series products
distance
here is su ject to the grade of
installed
transmission,
the ca le(s) has to e solid, not
stranded
path will kill the transmission performance
significantly!
232 and Auto EDID
boosts up your video/audio transmission distance up to 60m (200ft) in HDTV 1080i format, 40m
bit color depth.
HD-C5S4P also
ees the highest 3D video compatibility on
the market. With only one cost effective Cat.5/5e/6 cable, users can readily extend HDTV sources from DVD
ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant display
monitors including HDMI or DVI enabled TV sets or LCD PC monitors. With the advanced design for the latest
HD Master Audio or Dolby TrueHD audio, and HDCP supports and
ibility makes HDCP compliant DVD players or PS3 transmit utmost
high quality video and audio with a greater distance at the minimal cost, when integrating several components
and RS
-232 serial port
bonus feature allows users to boost IR control distance up to 100m (330 ft) and makes IR
In addition, serial port offers the
and receiving unit
HD-C5S4P-RX. The
transmitting unit is used to capture the input HDMI / DVI signals with IR control packets and carry
the signals
via one cost effective Cat.5/5e/6 cable. The receiving unit is responsible for equalizing the transmitted HDMI
signals. The transmission distance between the sending and
to 60m (200ft) at HD 720p or 1080i; or 40m (130ft) at Full HD 1080p. With an 8
-level
equalization rotary control on the receiving unit, users can adjust the equalization strength to the received
sion distance between source and destination.
Extends the transmission up to 60m (200ft) from the HDMI source at HD 1080i or 720p 24
-bit
-
bit
bit
installed
ca le(s), source
stranded
. Any keystone
significantly!

2
SPECIFICATIONS
Model Name HD-C5S4P
Technical
Role of usage Transmitter [TX] Receiver [RX]
HDMI compliance HDMI Deep Color & full 3D
HDCP compliance Yes
Video bandwidth Single-link 225MHz [6.75Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over UTP
transmission [24-bit]
Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]
HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Signal Equalization 8-level digital control at RX
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
ESD protection
[1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge]
[2] Core chipset
—
±8kV
PCB stack-up 4-layer board [impedance control — differential 100Ω; single 50Ω]
IR pass-thru Full-duplex bi-directional
RS-232 support Yes
Input 1x HDMI + 1x 3.5mm 1x RJ45 + 1x 3.5mm
Output 1x RJ45 + 1x 3.5mm 1x HDMI + 1x 3.5mm
In/ Out 1x DIN9 1x DIN9
HDMI source control
Controllable via IR pass-through from RX to TX and from TX to RX with IR extenders
IR remote control
Electro
-
optical characteristics:
τ
= 25° / Carrier frequency: 20
-
60kHz
HDMI connector Type A [19-pin female]
Min DIN connector DIN-9
RJ45 connector WE/SS 8P8C with 2 LED indicators
3.5mm connector IR blaster & IR receiver
Rotary control switch EDID Mode selection Signal level equalization
Mechanical
Housing
Metal enclosure
Dimensions
[L x W x H]
Model 71 x 91 x 35mm [2.8" x 3.6" x 1.4"]
Package 270 x 175 x 80mm [10.6" x 6.9" x 3.1"]
Carton
450 x 370 x 300mm [1'6" x 1'3" x 11.8"]
Weight Model TBA
Package TBA
Fixedness Wall-mounting case with screws
Power supply 5V 2A DC
Power consumption 1.5 Watts
Operation temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]

PANEL
Transmitting unit
Front Panel
1. RS-232:
Connect to PC serial port with a DSUB
2. MODE: A - EDID Full-HD(
1080p@60)
B - EDID Full-
HD(1080p@60)
C - EDID Full-
HD(1080p@60)
D - EDID Full-
HD(1080p@60)
E -
EDID HD(1080p@30)(1080i@60)(720p@60)
F -
EDID HD(1080p@30)(1080i@60)(720p@60)
G - EDID Full-
HD(1080p@60)
H – Auto EDID learning
3. Dip Switch: Setup the RS-
232 mode for serial communication channel
4. HDMI IN:
Connects to a HDMI source with a HDMI male
5. IR Receiver:
Infrared 3.5mm socket for plugging in the extension cable of IR receiver
6. IR Blaster:
Infrared 3.5mm socket for plugging in the extension cable of IR blaster
Rear Panel
7. +5V DC:
Connect to 5V DC power supply.
8. HDMI Signal OUT:
Plug in a Cat
HD-C5S4P-TX.
PANEL
DESCRIPTIONS
Transmitting unit
►
HD-C5S4P-TX
Connect to PC serial port with a DSUB
-9 male-male cable here
1080p@60)
- 24bit 2D video & 7.1ch audio
HD(1080p@60)
- 24bit 2D video & 2ch audio
HD(1080p@60)
- 24bit 3D video & 7.1ch audio
HD(1080p@60)
- 24bit 3D video & 2ch audio
EDID HD(1080p@30)(1080i@60)(720p@60)
-
24bit 2D video & 7.1ch audio
EDID HD(1080p@30)(1080i@60)(720p@60)
-
24bit 2D video & 2ch audio
HD(1080p@60)
- 36bit 2D video & 7.1ch audio
232 mode for serial communication channel
(see
p.5 for details)
Connects to a HDMI source with a HDMI male
-male cable
Infrared 3.5mm socket for plugging in the extension cable of IR receiver
Infrared 3.5mm socket for plugging in the extension cable of IR blaster
Connect to 5V DC power supply.
Plug in a Cat
-5/5e/6 cable that needs to be linked
to the transmitting unit
DESCRIPTIONS
24bit 2D video & 7.1ch audio
24bit 2D video & 2ch audio
p.5 for details)
Infrared 3.5mm socket for plugging in the extension cable of IR receiver
Infrared 3.5mm socket for plugging in the extension cable of IR blaster
to the transmitting unit

Receiving unit
Front Panel
9. RS-232:
Connect to PC serial port with a DSUB
10. Signal Level: Adjust the 8-
level equalization control to the received HDMI signals. The HDMI signal
level varies from MAX (strongest) to MIN (weakest) for respective transmission length from longest
possible range to short distance. Please adjust the signal level from
rotary switch whenever the audio/video is playing normally. Inappropriate signal level setting may
cause overpowering issue that would shorten the product life significantly!
11. Dip Switch: Setup the RS-
232 mode for serial
12. HDMI OUT:
Connect to a HDMI display with a HDMI male
13. IR Receiver:
Infrared 3.5mm socket for plugging in the extension cable of IR receiver
14. IR Blaster:
Infrared 3.5mm socket for plugging in the extension cable of IR blaster
Rear Panel
15. +5V DC:
Connect to 5V DC power supply.
16. HDMI Signal IN:
Plug in a Cat
HD-C5S4P-RX.
Receiving unit
► HD-C5S4P-RX
Connect to PC serial port with a DSUB
-9 male-male cable here
level equalization control to the received HDMI signals. The HDMI signal
level varies from MAX (strongest) to MIN (weakest) for respective transmission length from longest
possible range to short distance. Please adjust the signal level from
MIN to MAX and stop turning the
rotary switch whenever the audio/video is playing normally. Inappropriate signal level setting may
cause overpowering issue that would shorten the product life significantly!
232 mode for serial
communication channel (see p.5
for details)
Connect to a HDMI display with a HDMI male
-male cable.
Infrared 3.5mm socket for plugging in the extension cable of IR receiver
Infrared 3.5mm socket for plugging in the extension cable of IR blaster
Connect to 5V DC power supply.
Plug in a Cat
-5/5e/6 cable that needs to be link
ed to the receiving unit
level equalization control to the received HDMI signals. The HDMI signal
level varies from MAX (strongest) to MIN (weakest) for respective transmission length from longest
MIN to MAX and stop turning the
rotary switch whenever the audio/video is playing normally. Inappropriate signal level setting may
for details)
Infrared 3.5mm socket for plugging in the extension cable of IR receiver
Infrared 3.5mm socket for plugging in the extension cable of IR blaster
ed to the receiving unit

RS-232 Mode for Serial Communication Channel
DIP Switch Position Description
TX & RX
ON [

]
TxD: The 2
nd
pin of RS-232, which is in charge of receiving data
RxD: The 3
rd
pin of RS-232, which is in charge of sending data
OFF [

]
TxD: The 3
rd
pin of RS-232, which is in charge of receiving data
RxD: The 2
nd
pin of RS
-
232, which is in charge of
sending
d
ata
(TX MODULE)
Default RS232 Port Module Settings and Required DB9 Cables:
Both TX and RX modules are set to DCE mode as default mode (DIP switch down position). This
requires all RS232 9-Pin (DB9) to be straight-thru type. To connect the TX module DB9 port to
PC or control device, a DB9 Male to Female cable is needed while connecting RX module DB9
female port to RS232 device, a DB9 Male to Male cable is needed.
HD-C5S4P RS232 port is only for controlling A/V devices including HDTV, projector or switches
with serial control port. It will not work with other serial devices like modem or barcode scanner.
Learn more about RS232 Serial Interface:
http://en.wikipedia.org/wiki/RS-232

PACKAGE CONTENTS
1x HD-C5S4P[TX & RX] 1x IR blaster
1x IR receiver 2x DC 5V 2A wall wart
1x User Manual
CONNECTION DIAGRAM

IR
PASS
IR Extenders
IR Blaster
IR Sockets
IR BLASTER:
plug in the IR blaster to emit all IR command signals received from the IR receiver from the
other enf to control the devices corresponding to the IR signals.
IR RECEIVER:
plug in the IR receiver to receive all IR command signals from the IR remote controls of
the corresponding devices.
Definition of IR Earphone Jack
IR Blaster
You can uy any IR
extension
the IR sockets for the
matrix
than 2m (6-ft) may not
work
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR
extenders. Please check carefully
respective IR sockets. Warranty will not cover the damage.
CAUTION!
PASS
-THROUGH
IR Receiver
plug in the IR blaster to emit all IR command signals received from the IR receiver from the
other enf to control the devices corresponding to the IR signals.
plug in the IR receiver to receive all IR command signals from the IR remote controls of
Definition of IR Earphone Jack
IR Receiver
extension
ca les in the market that are compati le to
matrix
if necessary for replacement use. However,
work
.
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR
extenders. Please check carefully
before plugging in the IR extender to the
respective IR sockets. Warranty will not cover the damage.
plug in the IR blaster to emit all IR command signals received from the IR receiver from the
plug in the IR receiver to receive all IR command signals from the IR remote controls of
the definition of
IR ca les longer
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR
before plugging in the IR extender to the

8
HARDWARE INSTALLATION
1. Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the transmitting unit HD-C5S4P-TX.
2. Connect a HDMI or DVI display (such as a LCD TV) to the receiving unit HD-C5S4P-RX.
3. Connect IR Blaster/Receiver to both TX and RX units.
4. Connect a Cat-5/5e/6 cable between the transmitting and receiving units.
5. Make sure this Cat-5/5e/6 cable is tightly connected and not loose.
6. Plug in 5V DC power supply unit to the power jack of the receiving unit HD-C5S4P-RX.
7. Plug in 5V DC power supply unit to the power jack of the transmitting unit HD-C5S4P-TX.
8. If you see flickering or blinking image on the display, please adjust the rotary control switch to improve
the cable skew. MAX stands for the strongest HDMI signal level for longest possible transmission
length while MIN stands for the weakest HDMI signal level for short transmission length. Please adjust
the signal level from MIN to MAX and stop turning the rotary switch whenever the audio/video is
playing normally. Inappropriate signal level setting may cause overpowering issue that would shorten
the product life significantly!

PIN DEFINITION
HDMI
Type A (Receptacle) HDMI
Pin 1 TMDS Data2+ Pin 11 TMDS Clock Shield
Pin 2 TMDS Data2 Shield Pin 12 TMDS Clock–
Pin 3 TMDS Data2– Pin 13 CEC
Pin 4 TMDS Data1+ Pin 14 Reserved (N.C. on device)
Pin 5 TMDS Data1 Shield Pin 15 SCL
Pin 6 TMDS Data1– Pin 16 SDA
Pin 7 TMDS Data0+ Pin 17 DDC/CEC Ground
Pin 8 TMDS Data0 Shield Pin 18 +5V Power
Pin 9 TMDS Data0– Pin 19 Hot Plug Detect
Pin 10
TMDS
Clock+
CAT5 [RJ45]

1.
When adjusting the signal level on the receiver unit,
MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue that would shorten the product life significantly!
2. Wr
ongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of
the IR extenders. Please check carefully before plugging in the IR extender to the respective IR
sockets.
3.
If the DVI or HDMI device requires the EDID in
and provide DVI or HDMI display EDID information.
4.
All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP
cable and ASTRODESIGN Video Signal Generator VG
5.
The transmission length is largely affected by the type of Cat
and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m
[1,000ft] bulk cables) can transmit a lot l
fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid
UTP Cat-
5e cable shows longer transmission range than stranded STP Cat
ext
ension applications, solid UTP/STP cables are the only viable choice.
6. EIA/TIA-568-
B termination (T568B) for Cat
7.
To reduce the interference among the unshielded twisted pairs of wires in Cat
use shielded STP cables to improve EMI problems, which is worsen in long transmission.
8.
Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can
achieve and how good is the received picture quali
choice of Cat-
5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat
recommended.
9.
If your HDMI display has multiple HDMI inputs, it is found that the first HDMI inpu
generally can produce better transmission performance among all HDMI inputs.
Performance Guide for HDMI over Category Cable Transmission
Performance rating
Wiring Shielding
Solid Unshielded (UTP)
Shielded (STP)
Stranded Unshielded (UTP)
Shielded (STP)
Termination
NOTICE
When adjusting the signal level on the receiver unit,
please dial the rotary control switch from MIN to
MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue that would shorten the product life significantly!
ongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of
the IR extenders. Please check carefully before plugging in the IR extender to the respective IR
If the DVI or HDMI device requires the EDID in
formation, please use EDID Reader/Writer to retrieve
and provide DVI or HDMI display EDID information.
All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP
cable and ASTRODESIGN Video Signal Generator VG
-859C & VG-870B.
The transmission length is largely affected by the type of Cat
-
5/5e/6 cables, the type of HDMI sources,
and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m
[1,000ft] bulk cables) can transmit a lot l
onger signals than stranded UTP cables (usually in the form of
fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid
5e cable shows longer transmission range than stranded STP Cat
ension applications, solid UTP/STP cables are the only viable choice.
B termination (T568B) for Cat
-
5/5e/6 cables is recommended for better performance.
To reduce the interference among the unshielded twisted pairs of wires in Cat
-
5/5e/6
use shielded STP cables to improve EMI problems, which is worsen in long transmission.
Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can
achieve and how good is the received picture quali
ty, the actual transmission range is subject to one's
5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat
If your HDMI display has multiple HDMI inputs, it is found that the first HDMI inpu
generally can produce better transmission performance among all HDMI inputs.
Performance Guide for HDMI over Category Cable Transmission
Type of category cable
CAT5 CAT5e
 
 
 
 
Please use E A/T A-568-B termination (
T568B
please dial the rotary control switch from MIN to
MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
signal level setting may cause overpowering issue that would shorten the product life significantly!
ongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of
the IR extenders. Please check carefully before plugging in the IR extender to the respective IR
formation, please use EDID Reader/Writer to retrieve
All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP
5/5e/6 cables, the type of HDMI sources,
and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m
onger signals than stranded UTP cables (usually in the form of
fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid
5e cable shows longer transmission range than stranded STP Cat
-6 cable. For long
5/5e/6 cables is recommended for better performance.
5/5e/6
cable, one can
use shielded STP cables to improve EMI problems, which is worsen in long transmission.
Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can
ty, the actual transmission range is subject to one's
5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat
-6 cable is
If your HDMI display has multiple HDMI inputs, it is found that the first HDMI inpu
t [HDMI input #1]
Performance Guide for HDMI over Category Cable Transmission
CAT6




T568B
) at any time

11
WARRANTY
The SELLER warrants the HD-C5S4P HDMI extender over single cat.X with bi-directional IR
RS-232 and Auto EDID Learning free from defects in the material and workmanship for 1 year from the
date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good working
order within 1 year warranty period, The SELLER, at its option, repair or replace the unit, provided that the
unit has not been subjected to accident, disaster, abuse or any unauthorized modifications including static
discharge and power surge. This warranty is offered by the SELLER for its BUYER with direct transaction
only. This warranty is void if the warranty seal on the metal housing is broken.
Unit that fails under conditions other than those covered will be repaired at the current price of parts
and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment
to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or assume the risk of loss
or damage in transit. Under no circumstances will a unit be accepted without a return authorization
number.
The warranty is in lieu of all other warranties expressed or implied, including without limitations, any
other implied warranty or fitness or merchantability for any particular purpose, all of which are expressly
disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are responsible
for shipping charges to and from the SELLER. Cables and power adapters are limited to a 30 day
warranty and must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However, The
SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The
SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting
from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the
technical information contained herein regarding the HD-C5S4P features and specifications is subject to
change without further notice.