Kramer FC-46H2 User manual

P/N: 2900-300873 Rev 1 www.KramerAV.com
USER MANUAL
MODEL:
FC-46H2
4K HDMI Audio De-Embedder

Kramer Electronics Ltd.
FC-46H2 –Contents
i
Contents
Introduction 1
Getting Started 1
Overview 2
Typical Applications 3
Defining FC-46H2 4K HDMI Audio De-Embedder 4
Mounting FC-46H2 5
Connecting the FC-46H2 6
Connecting the Output to a Balanced/Unbalanced Stereo Audio Acceptor 7
Setting the DIP-Switches 7
Operating and Controlling the FC-46H2 8
Using the Front Panel Buttons 8
Connecting the Remote Control Switches 8
Technical Specifications 9
Default EDID 9

Kramer Electronics Ltd.
FC-46H2 –Introduction
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world
of unique, creative, and affordable solutions to the vast range of problems that confront the
video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we
have redesigned and upgraded most of our line, making the best even better!
Getting Started
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment.
•Review the contents of this user manual.
Go to www.kramerav.com/downloads/FC-46H2 to check for up-to-date user manuals,
application programs, and to check if firmware upgrades are available (where appropriate).
Achieving the Best Performance
•Use only good quality connection cables (we recommend Kramer high-performance,
high-resolution cables) to avoid interference, deterioration in signal quality due to poor
matching, and elevated noise levels (often associated with low quality cables).
•Do not secure the cables in tight bundles or roll the slack into tight coils.
•Avoid interference from neighboring electrical appliances that may adversely influence
signal quality.
•Position your Kramer FC-46H2 away from moisture, excessive sunlight and dust.
Safety Instructions
Caution:
•This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.
•For products with relay terminals and GPI\O ports, please refer to the permitted rating
for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•To ensure continuous risk protection, replace fuses only according to the rating
specified on the product label which located on the bottom of the unit.

Kramer Electronics Ltd.
FC-46H2 –Introduction
2
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/support/recycling.
Overview
Congratulations on purchasing your Kramer FC-46H2 4K HDMI Audio De-Embedder.
The FC-46H2 is a professional HDMI™audio de-embedder for HDMI signals up to 4K@60Hz
(4:4:4) resolution. The unit de-embeds the audio signal from the HDMI input or from the HDMI
output ARC (Audio Return Channel) and simultaneously outputs it to the S/PDIF and 5-pin
balanced audio outputs.
The FC-46H2 provides exceptional quality, advanced and user-friendly operation, and flexible
control.
Exceptional Quality
•Professional HDMI Audio De-embedder –De-embeds the audio from HDMI signals with
resolution up to 4K@60Hz (4:4:4) and data rate up to 18Gbps (6Gbps per graphic
channel), supporting HDR and HDCP 2.2/1.4.
•Kramer re-Klocking™ and Equalization Technology – Rebuilds the digital signal to travel
longer distances.
Advanced and User-friendly Operation
•Smart EDID Management –Select one of the EDID management modes using the
DIP-switches: pass-through, lock or force 2 channel LPCM.
•Convenient Control and Maintenance –Audio Source front panel button enables local
switching to either the HDMI input audio or the HDMI output ARC. Audio source, audio
output, and power LED indicators enable easy local maintenance and troubleshooting.
Local firmware upgrade via the mini USB port ensures lasting, field-proven deployment.
•Easy Installation –Compact DigTOOLS® fan-less enclosure for surface mounting or
side-by-side mounting of 3 units in a 1U rack space with the recommended rack adapter.
Flexible Connectivity
•Flexible De-embedding –De-embed the audio from the HDMI input or from the HDMI
output ARC (Audio Return Channel).
•Varied Output Options –De-embedded audio is simultaneously output to S/PDIF and
5-pin balanced audio outputs.

Kramer Electronics Ltd.
FC-46H2 –Introduction
3
Typical Applications
FC-46H2 is ideal for the following typical applications:
•Presentation and multimedia.
•Projection systems in conference rooms, boardrooms, auditoriums, hotels and churches,
production studios, rental and staging.
•Applications where an audio receiver is used for the HDMI soundtrack rather than
playing it through the display itself.
Controlling your FC-46H2
Control your FC-46H2 directly via the select audio source button.

Kramer Electronics Ltd.
FC-46H2 –Defining FC-46H2 4K HDMI Audio De-Embedder
4
Defining FC-46H2 4K HDMI Audio
De-Embedder
This section defines FC-46H2.
Figure 1: FC-46H2 4K HDMI Audio De-Embedder Front Panel
#
Feature
Function
PROG Mini USB Port
Connect to a PC to perform firmware upgrades (via K-Upload)
and work with the EDID Designer.
K-Upload and EDID Designer can be downloaded from our web
site at: www.kramerav.com/downloads/FC-46H2).
To use the mini USB port, you need to download the Kramer
USB driver from our web site at:
www.kramerav.com/support/product_downloads.asp and install it.
SETUP 4-way DIP-switch
Set the device behavior (see Setting the DIP-Switches
on page 7).
All the DIP-switches are set to off (up) by default.
AUDIO
SOURCE
Selector Button
Press to route the audio source from HDMI IN or from HDMI OUT
(ARC) to the audio outputs.
IN LED
Lights green when HDMI IN is selected.
OUT LED
Lights green when HDMI OUT is selected (ARC).
AUDIO OUT
LEDs
DIGITAL
Lights green when a de-embedded audio signal is present on the
S/PDIF output.
ANALOG
Lights green when a de-embedded audio signal is present on the
ANALOG audio output.
ON LED
Lights green when powered.
HDMI™IN Connector
Connect to an HDMI source.
HDMI™OUT Connector
Connect to an HDMI acceptor.
AUDIO OUT
Connectors
ANALOG 5-pin
Terminal Block
Connect to an analog audio acceptor.
S/PDIF RCA
Connect to a digital audio acceptor.
MUTE 2-pin Terminal Block
Connector
Connect the MUTE pin to GND to mute the analog audio output.
5V DC Power Connector
Connect to the Kramer power adapter.
1
2
3
4
5
6
7
8
9
10
11

Kramer Electronics Ltd.
FC-46H2 –Mounting FC-46H2
5
Mounting FC-46H2
This section provides instructions for mounting FC-46H2. Before installing, verify that the
environment is within the recommended range:
•Operation temperature –0to 40C (32 to 104F).
•Storage temperature –-40to +70C (-40 to +158F).
•Humidity –10% to 90%, RHL non-condensing.
Caution:
•Mount FC-46H2 before connecting any cables or power.
Warning:
•Ensure that the environment (e.g., maximum ambient temperature & air flow) is
compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be used for avoiding
overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.
To mount the FC-46H2 on a rack
Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/FC-46H2)
To mount the FC-46H2 on a table or shelf
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to
a flat surface.
For more information go to www.kramerav.com/downloads/FC-46H2

Kramer Electronics Ltd.
FC-46H2 –Connecting the FC-46H2
6
Connecting the FC-46H2
Always switch off the power to each device before connecting it to your FC-46H2. After
connecting your FC-46H2, connect its power and then switch on the power to each device.
Figure 2: Connecting to the FC-46H2 Rear Panel
To connect the FC-46H2 as illustrated in the example in Figure 2:
1. Connect an HDMI source (for example, a Blu-ray player) to the HDMI™ IN connector
.
2. Connect the HDMI™OUT connector to an HDMI acceptor (for example, a display).
3. Connect the AUDIO OUT:
▪The ANALOG 5-pin terminal block connector to an analog audio acceptor (for
example, a power amplifier with speakers).
▪The S/PDIF RCA connector to a digital audio acceptor (for example, a receiver).
4. Connect the MUTE 2-pin terminal block connector to a contact closure switch (for
example, Kramer RC-21TB,not shown in Figure 2).
5. Set the SETUP DIP-switches on the front panel (see Setting the DIP-Switches
on page 7).
6. Connect the power adapter to the FC-46H2 and to the mains electricity (not shown in
Figure 2).
6
7
8
9
8
2

Kramer Electronics Ltd.
FC-46H2 –Connecting the FC-46H2
7
Connecting the Output to a Balanced/Unbalanced
Stereo Audio Acceptor
The following are the pinouts for connecting the output to a balanced or unbalanced stereo
audio acceptor:
Figure 3: Connecting to a Balanced Stereo Audio
Acceptor
Figure 4: Connecting to an Unbalanced Stereo Audio
Acceptor
Setting the DIP-Switches
The four DIP-switches located on the front panel are used for managing EDID, defining audio
support and setting the amplification level. By default all DIP-switches are set to OFF (up).
Figure 5: DIP-Switches
#
Feature
DIP-switch Settings
1
EDID Mode
On (down) —EDID locked.
Off (up) —EDID pass-through mode.
When EDID is locked, the audio parameters are set as defined by DIP-
switch 2.
In pass-through mode, the DIP-switch 2 setup is ignored.
2
Audio Support
On (down) —Limits the audio to 2-channel LPCM.
Off (up) —Passes the audio signal.
This setup is enabled only after DIP-switch 1 is set to On (down; EDID
locked).
3/4
Analog Audio
Amplification Level
3
Off (up)
0dB
On (down)
6dB
Off (up)
12dB
On (down)
18dB
4
Off (up)
Off (up)
On (down)
On (down)
The DIP-switch status is sampled when the device is reset. The unit must be powered off and
on for the new settings to activate.

Kramer Electronics Ltd.
FC-46H2 –Operating and Controlling the
FC-46H2
8
Operating and Controlling the
FC-46H2
Using the Front Panel Buttons
The balanced analog audio and the S/PDIF Digital audio outputs work together to extract
either the output HDMI audio (the same audio that will be heard on the display) or the ARC
audio from the display.
Press the FC-46H2 front panel buttons to select the audio source:
•IN –Both audio outputs take the audio from the HDMI input.
•OUT –Both audio outputs take audio from the ARC (HDMI output).
The selected IN/OUT source LED lights green.
The AUDIO OUT LEDs indicate the type of de-embedded signal present on the outputs. For
example:
•When uncompressed multi-channel LPCM audio is used, the analog audio port only
outputs the Front-left and Front-right audio. When compressed audio is used, the analog
audio port is muted.
•When Dolby/DTS 5.1 is present, the analog output is muted so the ANALOG LED is off
and the DIGITAL LED lights green.
Connecting the Remote Control Switches
Mute the analog output by connecting the MUTE pin to the GND.
Figure 6: Muting the Analog Audio Output

Kramer Electronics Ltd.
FC-46H2 –Technical Specifications
9
Technical Specifications
Input
HDMI
On a female HDMI connector
Outputs
HDMI
On a female HDMI connector
S/PDIF Digital Audio
On an RCA connector
Balanced Stereo Analog Audio
On a 5-pin terminal block connector
Video
Bandwidth
Up to 18Gbps (6Gbps per graphic channel)
Max. Resolution
Up to 4K@60 (4:4:4)
Compliance
HDCP 2.2
Line Level
Output
Frequency Response
20Hz - 20kHz @ +/-0.5dB
S/N Ratio:
>89dB (THD + Noise)
Audio THD + Noise:
0.004%
Controls
Front Panel
AUDIO SOURCE (IN and OUT), AUDIO OUTPUT
(DIG and ANALOG), and ON LED indicators
SETUP DIP-switches: EDID mode, audio settings,
analog audio amplification
Rear Panel
MUTE output contact closure pins
Power
Consumption
5V DC, 370mA
Source
5.2V DC, 4A
Environmental
Conditions
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory
Compliance
Safety
CE,
Environmental
RoHs, WEEE
Enclosure
Size
Tool
Type
Aluminum
Cooling
Convection ventilation
General
Net Dimensions (W, D, H), each
12cm x 7.2cm x 2.4cm
(4.7" x 2.8" x 0.94")
Shipping Dimensions
(W, D, H)
15.7cm x 12cm x 8.7cm
(6.2" x 4.7" x 3.4")
Net Weight, each
0.2kg (0.44bs) approx.
Shipping Weight
0.7 kg (1.5lbs) approx.
Accessories
Included
1 Power adapter, 1 power cord and 1 bracket set
Specifications are subject to change without notice at www.kramerav.com
Default EDID
Monitor
Model name............... FC-46H2
Manufacturer............. KMR
Plug and Play ID......... KMR1200
Serial number............ 295-883450100
Manufacture date......... 2018, ISO week 255
Filter driver............ None
-------------------------
EDID revision............ 1.3
Input signal type........ Digital
Color bit depth.......... Undefined
Display type............. Monochrome/grayscale
Screen size.............. 520 x 320 mm (24.0 in)
Power management......... Standby, Suspend, Active off/sleep
Extension blocs.......... 1 (CEA-EXT)
-------------------------
DDC/CI................... Not supported
Color characteristics

Kramer Electronics Ltd.
FC-46H2 –Technical Specifications
10
Default color space...... Non-sRGB
Display gamma............ 2.20
Red chromaticity......... Rx 0.674 - Ry 0.319
Green chromaticity....... Gx 0.188 - Gy 0.706
Blue chromaticity........ Bx 0.148 - By 0.064
White point (default).... Wx 0.313 - Wy 0.329
Additional descriptors... None
Timing characteristics
Horizontal scan range.... 30-83kHz
Vertical scan range...... 56-76Hz
Video bandwidth.......... 170MHz
CVT standard............. Not supported
GTF standard............. Not supported
Additional descriptors... None
Preferred timing......... Yes
Native/preferred timing.. 1920x1080p at 60Hz (16:9)
Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 1024p at 75Hz - VESA STD
1280 x 1024p at 85Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
1024 x 768p at 85Hz - VESA STD
800 x 600p at 85Hz - VESA STD
640 x 480p at 85Hz - VESA STD
1152 x 864p at 70Hz - VESA STD
1280 x 960p at 60Hz - VESA STD
EIA/CEA-861 Information
Revision number.......... 3
IT underscan............. Supported
Basic audio.............. Supported
YCbCr 4:4:4.............. Not supported
YCbCr 4:2:2.............. Not supported
Native formats........... 1
Detailed timing #1....... 1920x1080p at 60Hz (16:10)
Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
Detailed timing #2....... 1920x1080i at 60Hz (16:10)
Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync +vsync
Detailed timing #3....... 1280x720p at 60Hz (16:10)
Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
Detailed timing #4....... 720x480p at 60Hz (16:10)
Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync
CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz
CE video identifiers (VICs) - timing/formats supported
1920 x 1080p at 60Hz - HDTV (16:9, 1:1) [Native]
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1)
720 x 480p at 60Hz - EDTV (16:9, 32:27)
720 x 480p at 60Hz - EDTV (4:3, 8:9)
720 x 480i at 60Hz - Doublescan (16:9, 32:27)
720 x 576i at 50Hz - Doublescan (16:9, 64:45)
640 x 480p at 60Hz - Default (4:3, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001
CE vendor specific data (VSDB)
IEEE registration number. 0x000C03
CEC physical address..... 1.1.0.0
Maximum TMDS clock....... 165MHz
CE speaker allocation data

Kramer Electronics Ltd.
FC-46H2 –Technical Specifications
11
Channel configuration.... 2.0
Front left/right......... Yes
Front LFE................ No
Front center............. No
Rear left/right.......... No
Rear center.............. No
Front left/right center.. No
Rear left/right center... No
Rear LFE................. No
Report information
Date generated........... 28/02/2019
Software revision........ 2.70.0.989
Data source.............. Real-time 0x0071
Operating system......... 6.1.7601.2.Service Pack 1
Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,01,01,01,01,FF,1C,01,03,80,34,20,78,E2,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,02,3A,80,18,71,38,2D,40,58,2C,
45,00,A0,5A,00,00,00,1E,00,00,00,FF,00,32,39,35,2D,38,38,33,34,35,30,31,30,30,00,00,00,FC,00,46,
43,2D,34,36,48,32,0A,20,20,20,20,20,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,01,D0,
02,03,1B,C1,23,09,07,07,48,90,05,04,03,02,07,16,01,65,03,0C,00,11,00,83,01,00,00,02,3A,80,18,71,
38,2D,40,58,2C,45,00,07,44,21,00,00,1E,01,1D,80,18,71,1C,16,20,58,2C,25,00,07,44,21,00,00,9E,01,
1D,00,72,51,D0,1E,20,6E,28,55,00,07,44,21,00,00,1E,8C,0A,D0,8A,20,E0,2D,10,10,3E,96,00,07,44,21,
00,00,18,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,76

The warranty obligations of Kramer Electronics Inc. (“Kramer Electronics”) for this product are limited to the terms set forth below:
What is Covered
This limited warranty covers defects in materials and workmanship in this product.
What is Not Covered
This limited warranty does not cover any damage, deterioration or malfunction resulting from any alteration, modification, improper or unreasonable use
or maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire, improper packing and shipping (such claims must be presented to
the carrier), lightning, power surges, or other acts of nature. This limited warranty does not cover any damage, deterioration or malfunction resulting
from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone
unauthorized by Kramer Electronics to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship
of this product. This limited warranty does not cover cartons, equipment enclosures, cables or accessories used in conjunction with this product.
Without limiting any other exclusion herein, Kramer Electronics does not warrant that the product covered hereby, including, without limitation, the
technology and/or integrated circuit(s) included in the product, will not become obsolete or that such items are or will remain compatible with any other
product or technology with which the product may be used.
How Long this Coverage Lasts
The standard limited warranty for Kramer products is seven (7) years from the date of original purchase, with the following exceptions:
1. All Kramer VIA hardware products are covered by a standard three (3) year warranty for the VIA hardware and a standard three (3) year
warranty for firmware and software updates; all Kramer VIA accessories, adapters, tags, and dongles are covered by a standard one (1) year
warranty.
2. All Kramer fiber optic cables, adapter-size fiber optic extenders, pluggable optical modules, active cables, cable retractors, all ring mounted
adapters, all Kramer speakers and Kramer touch panels are covered by a standard one (1) year warranty.
3. All Kramer Cobra products, all Kramer Calibre products, all Kramer Minicom digital signage products, all HighSecLabs products, all
streaming, and all wireless products are covered by a standard three (3) year warranty.
4. All Sierra Video MultiViewers are covered by a standard five (5) year warranty.
5. Sierra switchers & control panels are covered by a standard seven (7) year warranty (excluding power supplies and fans that are covered for
three (3) years).
6. K-Touch software is covered by a standard one (1) year warranty for software updates.
7. All Kramer passive cables are covered by a ten (10) year warranty.
Who is Covered
Only the original purchaser of this product is covered under this limited warranty. This limited warranty is not transferable to subsequent purchasers or
owners of this product.
What Kramer Electronics Will Do
Kramer Electronics will, at its sole option, provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper
claim under this limited warranty:
1. Elect to repair or facilitate the repair of any defective parts within a reasonable period of time, free of any charge for the necessary parts and
labor to complete the repair and restore this product to its proper operating condition. Kramer Electronics will also pay the shipping costs
necessary to return this product once the repair is complete.
2. Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same
function as the original product.
3. Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought
under this limited warranty.
What Kramer Electronics Will Not Do Under This Limited Warranty
If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer
Electronics products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned
uninsured, you assume all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or re-
installation of this product from or into any installation. Kramer Electronics will not be responsible for any costs related to any setting up this product, any
adjustment of user controls or any programming required for a specific installation of this product.
How to Obtain a Remedy Under This Limited Warranty
To obtain a remedy under this limited warranty, you must contact either the authorized Kramer Electronics reseller from whom you purchased this
product or the Kramer Electronics office nearest you. For a list of authorized Kramer Electronics resellers and/or Kramer Electronics authorized service
providers, visit our web site at www.kramerav.com or contact the Kramer Electronics office nearest you.
In order to pursue any remedy under this limited warranty, you must possess an original, dated receipt as proof of purchase from an authorized Kramer
Electronics reseller. If this product is returned under this limited warranty, a return authorization number, obtained from Kramer Electronics, will be
required (RMA number). You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product.
If it is decided that this product should be returned directly to Kramer Electronics, this product should be properly packed, preferably in the original
carton, for shipping. Cartons not bearing a return authorization number will be refused.
Limitation of Liability
THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID
FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL
THEORY. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental, consequential or indirect damages, or
the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you.
Exclusive Remedy
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE MAXIMUM EXTENT
PERMITTED BY LAW, KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR
EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPLICABLE LAW.
IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A “CONSUMER PRODUCT” UNDER THE MAGNUSON-MOSS WARRANTY ACT (15
U.S.C.A. §2301, ET SEQ.) OR OTHER APPLICABLE LAW, THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU, AND
ALL IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE,
SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW.
Other Conditions
This limited warranty gives you specific legal rights, and you may have other rights which vary from country to country or state to state.
This limited warranty is void if (i) the label bearing the serial number of this product has been removed or defaced, (ii) the product is not distributed by
Kramer Electronics or (iii) this product is not purchased from an authorized Kramer Electronics reseller. If you are unsure whether a reseller is an
authorized Kramer Electronics reseller, visit our web site at www.kramerav.com or contact a Kramer Electronics office from the list at the end of this
document.
Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the
online product registration form. Kramer Electronics thanks you for purchasing a Kramer Electronics product. We hope it will give you years of
satisfaction.

www.KramerAV.com
[e-mail]
P/N:
2900-300873
Rev:
1
SAFETY WARNING
Disconnect the unit from the power supply before opening andservicing
For the latest information on our products and a list of Kramer distributors, visit our Web site where
updates to this user manual may be found.
We welcome your questions, comments, and feedback.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
All brand names, product names, and trademarks are the property of their respective owners.