Hdav HD4?C6E User manual

TECHNICAL SPECIFICATIONS:
-Max. Resolutions HDTV: 480p, 720p, 1080i/p
PC: 1920x1200 @ 60Hz
-HDMIAudio Support Stereo, DTS-HD, Dolby TrueHD
-HDMI Video Bandwidth 340MHz (10.2Gbps)
-HDCP/DDC/CEC Supported
-TMDS Input Voltage 1.2v (peak-to-peak)
DDC Input Voltage 5v (peak-to-peak)
-IR Frequency 20-80KHz
-IR Cable Max Distance 15-Meters
-Serial Protocol RS-232C
-Serial Bandwidth Up to 57600bps / Full Duplex
-LAN Protocol Ethernet 10/100BaseT
-LAN Bandwidth Up to 100MHz
-LAN Protocol IEEE802.1q, 2.3, 2.3u, 2.3x
-LAN Cable Termination T568B Pin-out / Straight Thru
-Connectors RJ45 LAN, HDMI, 3.5mm IR, DB9
-Power Supply Only TX Module required External Power
24v 1A DC / 100v-240vAC
-Operating Temperature 320F to 1580F
-Enclosure / Net Weight Metal / 1.09 Lb per Module
-Standards HDMI v1.4a, DVI 1.0, HDCP v1.1
FCC, CE, RoHS
-Warranty One Year
-Country of Origin Taiwan
-SKU / UPC HD4-C6E / 0 37229 00799 2

Do not attempt to service this unit yourself. Provide proper ventilation and air circulation.
v1.1
Allnamesandtrademarksarepropertyoftheirrespectivecompanies.
Allinformationissubjecttochangewithoutnotice.

HDMIv1.43D/CEC
4‐in‐1100‐Meter1xCAT6Ext.Kit
withBuilt‐inRS‐232&IRControl
and6‐PortsFastEthernetHub


SetupGuide

(HD4‐C6E)
[MustbeusedwithSolidCAT6Cables]
Note:HD4‐C6EdoesnotsupportHDMIv1.4EthernetChannelandARC.


INSTALLATION (POINT TO POINT)
1. Connect the HDMI source device to the transmitter module (TX)
Connect the IR blaster to HD4-C6E transmitter module
2. Connect the HD display to the receiver module (RX)
3. Connect HDE-K TX & RX units Gigalink Port using solid CAT6/6a cable.
4. Connect the power adaptor to TX and power on the TX module
5. Turn-on the HD display, then turn-on the HDMI source device
Note: The blue line that connects the 2 modules must be solid CAT6 straight-thru
cable terminated in T568-B configuration. Maximum distance is 100-meters.
T568-B CABLE CONFIGURATION:
INSTALLATION (HDMI +ETHERNET)
1. Connect the HDMI source device to the transmitter module (TX)
Connect the IR blaster to TX
2. Connect the HD display to the receiver module (RX)
3. Connect the HD display to the TX “BYPASS OUT” port (optional)
4. Connect HDE-K TX & RX units Gigalink Port using solid CAT6/6a cable.
5. Connect the power adaptor to TX and power on the TX module
6. Turn-on the HD display, then turn-on the HDMI source device
7. Connect an Ethernet/Internet Router to one of the Ethernet port on TX module
8. Connect computer & a/v devices to the remaining Ethernet ports either on the
TX or RX modules for internet access (if available).
9. Connect the RS-232 port on the TX to a computer’s serial port
10. Connect the RS-232 port on the RX to the display’s serial port
Note: Do put an ethernet switch/router between the TX and RX modules.
IR PIN CONFIGURATION:
ExternalIRIN(optionalcable) ExternalIROUT(cableincluded)


INSTALLATION DIAGRAM:
RS-232 CONFIGURATION:
Pin‐out:2‐3/3‐2/5‐5
Settings: Bitspersecond:57600
  Databits:8/Parity:None
  Stopbit:1/FlowControl:None
RequiredRS‐232Cable:DB9M/FStraightThruCables
RecommendedCables:CC317Series
Forinternetconnection,theroutermustbeconnectedtointernetservice.
TheHD4‐C6EdoesnotsupportHDMIoverEthernetandisdependenton
externalroutertoprovideHDCPtoconnecteddevices.HDsources&
displays,router,computers,remotecontrolandrequiredcablesarenot
includedinthepackage.
INSTALLATION (HDMI +ETHERNET WITH BYPASS PORT)

WhenanHDdisplayisconnectedtoTXHDMI“Bypass”port,thedisplay
connectedtotheRXmodulewillbeblank.Itisnotapass‐thrulocalHDMI
port.Usethebypassportfortroubleshootingpurposesonly.