Health Care Logistics 10650 User manual

Call Free 1.800.848.1633 • Fax Free 1.800.447.2923
Web: GoHCL.com • Email: [email protected]
ASSEMBLY INSTRUCTIONS FOR
IV Poles (#10650 & 10651)
© Health Care Logistics, Inc. 2012
Step 1. Slide the 5-footed
plastic mid-section onto the
larger end of the tripod tube.
Push down on it until it
comes to a stop.
The IV Pole should include:
A 1 tripod tube
B 1 5-footed plastic mid-section
C 1 clamp disk
D 2 feet with locking casters
E 2 feet with electrically conductive casters
F 1 foot with a regular swivel caster
G 1 top and 1 bottom plastic IV holder
H 1 drip glass, 1 glass-holder ring
I 1 wrench (not pictured)
Step 2. Place the clamp disk with the grooves facing
downward onto the 5-footed plastic mid-section.
Step 3. Place the locking spacer into the center opening of
the clamp disk. The teeth should fit down against the disk.
Grooves
C
E
D
F
H
B
G
A

Call Free 1.800.848.1633 • Fax Free 1.800.447.2923
Web: GoHCL.com • Email: [email protected]
ASSEMBLY INSTRUCTIONS FOR
IV Poles (#10650 & 10651)
© Health Care Logistics, Inc. 2012
Step 4. Thread the cheese-head screw into the locking spacer
leaving it loose so the feet can still be easily inserted into the
footed mid-section.
Electrically
Conductive
Caster
Electrically
Conductive
Caster
Locking
Caster
Locking
Caster
Regular
Caster
Step 7. Attach the two feet with locking casters opposite one
another. Mount the remaining foot with the regular swivel
caster onto the 5-footed plastic mid-section.
Step 6. Attach the second foot with an electrically conductive
caster as shown above, opposite the first.
Step 5. (A) Lift the clamp disk up and slide one of the feet
with electrically conductive casters into the 5-footed plastic
mid-section. (B) Align the groove on the clamp disk with the
hole in the foot and push the clamp disk down until they
snap together.
A
B

Call Free 1.800.848.1633 • Fax Free 1.800.447.2923
Web: GoHCL.com • Email: [email protected]
ASSEMBLY INSTRUCTIONS FOR
IV Poles (#10650 & 10651)
© Health Care Logistics, Inc. 2012
Step 9. Turn the IV Pole over so that the casters are on
the floor. Loosen the height adjuster by turning it counter
clockwise to adjust the telescoping section to the desired
height. Tighten the height adjuster by turning it clockwise to
lock the telescoping section at the correct height.
Step 10.Slide the open end of the bottom section of the
Plastic IV Holder onto the top of the tripod tube. (To bring the
bottom of the Plastic IV Holder to the correct insertion depth,
push it down by hand or tap with a rubber mallet until it
stops.)
Height
Adjuster
Step 8. Make sure the grooves of the clamp disks are in
the holes of the feet. Tighten the clamp disk by turning the
cheese-head screw clockwise with a hexagon socket-head
wrench to secure all five feet into the 5-footed plastic mid-
section.

Call Free 1.800.848.1633 • Fax Free 1.800.447.2923
Web: GoHCL.com • Email: [email protected]
ASSEMBLY INSTRUCTIONS FOR
IV Poles (#10650 & 10651)
© Health Care Logistics, Inc. 2012
Step 12.Hold the tripod tube and lightly tap the top of the
plastic IV holder with a rubber mallet until the top overlaps
the bottom section.
Step 11.Insert the tabs on the top section of the Plastic IV
Holder into the grooves on the bottom section of the Plastic
IV Holder.
Step 13. Clip the glass-holder ring onto the tripod tube.

Call Free 1.800.848.1633 • Fax Free 1.800.447.2923
Web: GoHCL.com • Email: [email protected]
ASSEMBLY INSTRUCTIONS FOR
IV Poles (#10650 & 10651)
© Health Care Logistics, Inc. 2012
Step 14.Place the drip glass into the glass-holder ring.
Step 15. Hang an IV bag or bottle onto the
Plastic IV Holder. The pole is now ready for
use.