HEALTH RIDER 15.5 S Elliptical User manual

Model No. HRCCEL2927.2
Serial No.
Write the serial number in the
space above for reference.
Serial
Number
Decal
USERʼS MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. eep this manual
for future reference.
QUESTIONS?
If you have questions, or if parts
are damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-936-4266
Mon.–Fri., 7:30 until 16:30 ET
(excluding holidays)
OR E-MAIL US:
[e-mail]
www.healthrider.com

2
HEALTHRIDER is a registered trademark of ICON IP, Inc.
TABLE OF CONTENTS
WARNINGDECALPLACEMENT..............................................................2
IMPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSEMBLY ...............................................................................5
HOWTOUSETHEELLIPTICALEXERCISER ..................................................10
MAINTENANCEANDTROUBLESHOOTING ...................................................13
EXERCISEGUIDELINES ...................................................................15
PARTLIST ..............................................................................18
EXPLODEDDRAWING ....................................................................19
ORDERINGREPLACEMENTPARTS ..................................................BackCover
LIMITEDWARRANTY ..............................................................BackCover
WARNING DECAL PLACEMENT
The warning decal shown here has
been applied in the location shown. If a
decal is missing or illegible, see the
front cover of this manual and
request a free replacement decal.
Apply the decal in the location shown.
Note: The decal may not be shown at
actual size.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
2. Use the elliptical exerciser only as described
in this manual.
3. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
4. The elliptical exerciser is intended for
home use only. Do not use the elliptical exer-
ciser in a commercial, rental, or institutional
setting.
5. eep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is at least 3 ft. (0.9 m) of
clearance in the front and rear of your ellipti-
cal exerciser and 2 ft. (0.6 m) on each side.
6. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
7. eep children under age 12 and pets away
from the elliptical exerciser at all times.
8. The elliptical exerciser should not be used
by persons weighing more than 250 lbs.
(113 kg).
9. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical exerciser. Always
wear athletic shoes for foot protection while
exercising.
10. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical exerciser.
11. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
12. eep your back straight while using the
elliptical exerciser; do not arch your back.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
14. When you stop exercising, allow the pedals
to slowly come to a stop.
IMPORTANT PRECAUTIONS

4
BEFORE YOU BEGIN
Thank you for selecting the new HEALTHRIDER®15.5
S elliptical exerciser. The 15.5 S provides a selection
of features designed to make your workouts at home
more effective and enjoyable.
For your benefit, read this manual carefully before
using the elliptical exerciser. If you have questions
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Pulse Sensor
Upper Body Arm
Pedal Disc
*Water bottle is not included
Pedal
Console
Water Bottle Holder*
Fan

5
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove all
packing materials; do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires an adjustable wrench , a Phillips
screwdriver , and a rubber mallet .
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parenthe-
ses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The
number following the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware
kit, check to see if it has been preassembled.
M10 Split
Washer (45)–2
M10 Locknut
(33)–6
M10
Washer (35)–2
M8 Locknut
(38)–4
M8 x 45mm Button Bolt (50)–4
M10 x 27mm
Patch Screw (40)–2
M10 x 75mm Carriage Bolt (34)–4M10 x 74mm Button Bolt (7)–2
Wave
Washer (69)–2
M8 Split
Washer (28)–4
Upper Body Arm
Washer (55)–2
M8 x 25mm Patch
Screw (56)–2
M8
Washer (71)–4
Console Screw
(59)–4
M8 x 52mm Button
Screw (27)–4
M10 Bolt Set (25)–2
Large Wave
Washer (76)–2
M4 x 22mm
Screw (63)–2

6
2. While another person lifts the back of the Frame
(1), attach the other Stabilizer (9) to the Frame
with two M10 x 75mm Carriage Bolts (34) and
two M10 Locknuts (33).
34
9
1
2
33
33
3. The Console (23) requires four 1.5V D batteries
(not included); alkaline batteries are recom-
mended. IMPORTANT: If the elliptical
exerciser has been exposed to cold temper-
atures, allow it to warm to room temperature
before inserting batteries into the Console. If
you do not do this, the console displays or
other electronic components may become
damaged. Remove the battery cover from the
Console, and insert four batteries into the
Console. Make sure that the batteries are ori-
ented as shown by the diagrams on the
battery cover. Then, reattach the battery cover.
23
Batteries
Batteries
Battery
Cover
3
9
33
21
21
34
1
1
1.
Identify the Stabilizer (9) which has round Caps
(21) on the ends.
While another person lifts the front of the Frame
(1), attach the Stabilizer (9) to the Frame with
two M10 x 75mm Carriage Bolts (34) and two
M10 Locknuts (33).
To make assembly easier, read the
information on page 5 before you begin.

7
4. While another person holds the Console (23)
near the Upright (2), connect the console wire
to the Upper Wire Harness (68).
Tip: Avoid pinching the wires. Attach the
Console (23) to the Upright (2) with the four
Console Screws (59) included with the Console.
Attach the Water Bottle Holder (29) to the
Upright (2) with two M4 x 22mm Screws (63).
4
23
2
59
Console Wire
Avoid pinching
the wires
29
63
68
5
1
2
33
Avoid pinching
the wires
73
68
7
45
5. While another person holds the Upright (2) near
the Frame (1), connect the Upper Wire Harness
(68) to the Lower Wire Harness (73).
Insert the Upper Wire Harness (68) and the
Lower Wire Harness (73) downward into the
Frame (1).
Tip: Avoid pinching the wires. Slide the
Upright (2) onto the Frame (1).
Attach the Upright (2) with two M10 x 74mm
Button Bolts (7), two M10 Split Washers (45),
and two M10 Locknuts (33). Do not tighten the
Button Bolts yet.

8
50
8
38
6. Identify the Left Upper Body Arm (6), which is
marked with a “Left” sticker.
Insert the Left Upper Body Arm (6) into one of
the Upper Body Legs (5); make sure that the
hexagonal holes are on the indicated side.
Attach the Left Upper Body Arm (6) with two M8
x45mm Button Bolts (50) and two M8 Locknuts
(38). Make sure that the Locknuts are inside
the hexagonal holes. Do not tighten the
Button Bolts yet.
Apply a generous amount of the included
grease to the Pivot Axle (26). Then, insert the
Pivot Axle into the Upright (2), and center it.
Turn an Upper Body Arm Spacer (47) so that
the small arrow on the Upper Body Arm Spacer
is pointing downward, and slide the Upper Body
Arm Spacer onto the Left Upper Body Arm (6).
Next, slide the Left Upper Body Arm (6) onto
the Pivot Axle (26).
Tighten an M8 x 25mm Patch Screw (56), an
Upper Body Arm Washer (55), and a Wave
Washer (69) into the Pivot Axle (26).
Then, press the tabs on a Upper Body Arm Cap
(46) into the Upper Body Arm Spacer (47).
Assemble the Right Upper Body Arm (8) and
the other Upper Body Leg (5) in the same
way.
Grease
6
47
Arrow
5
2
5
55
46
26
56
69
6
Hexagonal
Holes
7
27
71
11
13
71
28
28
7. Identify the Left Pedal Arm (11), which is
marked with a “Left” sticker.
Attach the Left Pedal (13) to the Left Pedal Arm
(11) with two M8 x 52mm Button Screws (27),
two M8 Split Washers (28), and two M8
Washers (71).
Attach the Right Pedal (not shown) in the
same way.

9
9. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
8. Apply grease to the axle on the left Disc
Crossbar (16).
Slide the Left Pedal Arm (11) onto the axle on
the left Disc Crossbar (16).
Apply grease to a Large Wave Washer (76) and
press it onto the end of the Left Pedal Arm (11).
Tighten an M10 x 27mm Patch Screw (40) and
an M10 Washer (35) into the axle.
Then, press a Pedal Arm Cap (74) into the Left
Pedal Arm (11).
Next, apply grease to an M10 Bolt Set (25).
Hold the lower end of the left Upper Body Leg
(5) inside the bracket on the Left Pedal Arm
(11).
Attach the Upper Body Leg (5) to the Left Pedal
Arm (11) with the M10 Bolt Set (25). Do not
overtighten the Bolt Set; the Upper Body
Leg must pivot freely.
Attach the Right Pedal Arm (not shown) to
the right side of the elliptical exerciser in the
same way.
See step 5. Tighten the M10 x 74mm Button
Bolts (7).
See step 6. Tighten the M8 x 45mm Button
Bolts (50).
Grease
Grease
16
25
11
40
74
35
76
11
25
5
2
8

10
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To mount the elliptical exerciser, hold the console or
the upper body arms and step onto the pedal that is in
the lowest position. Then, step onto the other pedal.
Push the pedals until they begin to move with a con-
tinuous motion. Note: The pedal discs can turn in
either direction. It is recommended that you move
the pedal discs in the direction shown by the
arrow; however, for variety, you can turn the pedal
discs in the opposite direction.
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. Note: The elliptical
exerciser does not have a free wheel; the pedals
will continue to move until the flywheel stops.
When the pedals are stationary, step off the highest
pedal first. Then, step off the lowest pedal.
The upper body arms are designed to add upper-body
exercise to your workouts. As you exercise, push and
pull the upper body arms to work your arms, shoul-
ders, and back.
Pedals
Upper Body Arms

11
HOW TO USE THE CONSOLE
1. Turn on the console.
Note: The console requires four 1.5V D batteries
(see assembly step 3 on page 6). If there is a
sheet of clear plastic on the face of the console,
remove the plastic.
To turn on the console, press the increase button
or begin pedaling.
2. Change the resistance of the pedals as
desired.
As you pedal,
change the resis-
tance of the
pedals by pressing
the increase or
decrease button.
The selected
resistance level
will be shown in the upper display.
Note: After a button is pressed, it will take a
moment for the pedals to reach the selected resis-
tance level.
3. Follow your progress with the displays.
The lower left
display can show
the elapsed time
and the distance
(total number of
revolutions) that
you have pedaled.
The lower right
display can show
your pedaling
speed (in revolu-
tions per minute)
and the approxi-
mate number of calories you have burned.
When you use the handgrip pulse sensor, the
lower right display will also show your heart rate
(see step 4 on page 12).
Increase Button
Decrease Button
CONSOLE DIAGRAM

12
The upper dis-
play is the priority
display. The prior-
ity display can
show the elapsed
time, the distance
that you have ped-
aled, your pedaling speed, or the approximate
number of calories you have burned.
Press the Display button repeatedly until the prior-
ity display shows the information that you are most
interested in viewing. Note: While information is
shown in the priority display, the information will
not be shown in the lower left or right display.
4. Measure your heart rate if desired.
If there are
sheets of clear
plastic on the
metal contacts
on the handgrip
pulse sensor,
remove the plas-
tic. In addition,
make sure that
your hands are
clean. To mea-
sure your heart rate, hold the handgrip pulse
sensor with your palms resting against the metal
contacts. Avoid moving your hands or gripping
the contacts tightly.
When your pulse is detected, the heart-shaped
indicator in the lower right display will flash each
time your heart beats. After a moment, your heart
rate will be shown. For the most accurate heart
rate reading, hold the contacts for at least 15 sec-
onds.
If your heart rate is not shown, make sure that
your hands are positioned as described. Be care-
ful not to move your hands excessively or to
squeeze the metal contacts tightly. For optimal
performance, clean the metal contacts using a soft
cloth; never use alcohol, abrasives, or chemi-
cals to clean the contacts.
5. Turn on the fan if desired.
The fan has high and low speed settings. Press
the Fan button repeatedly to select a fan speed or
to turn off the fan. Note: If the pedals do not move
for about thirty seconds, the fan will turn off auto-
matically.
Rotate the thumb
wheel on the right
side of the console
to pivot the fan to
the desired angle.
6. When you are finished exercising, the console
will turn off automatically.
If the pedals are not moved for a few seconds, the
displays will pause and the priority display will
flash.
If the pedals are not moved and the console but-
tons are not pressed for a few minutes, the
console will turn off to conserve the batteries.
Metal Contacts
Thumb Wheel

13
Inspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap. IMPORTANT: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
CONSOLE TROUBLESHOOTING
If the console display become dim, the batteries
should be replaced; most console problems are the
result of low batteries. See assembly step 3 on page 6
for replacement instructions.
If the console does not display your heart rate when
you hold the handgrip pulse sensor, or if the displayed
heart rate appears to be too high or too low, see step
4 on page 12.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
To adjust the reed switch, you must first remove the
Right Pedal Arm (12), the right Pedal Disc (15), and
the Shields (3, 4). See step 8 on page 9 and remove
the Right Pedal Arm.
Next, remove the four Screws (51, 70) from the right
Pedal Disc (15), and slide the Pedal Disc off.
Remove all Screws (52, 64) from the Right Shield (4)
and the two Bolts (41) from beneath the Pedal Disc,
and remove the Right Shield (4). Remove all Screws
(52) from the Left Shield (3), and move the Left
Shield.
Next, see the drawing below and locate the Reed
Switch (53). Loosen, but do not remove, the indicated
M4 x 16mm Self-tapping Screw (52). Slide the Reed
Switch slightly toward or away from the Magnet (58)
on the Flywheel (17). Retighten the Screw. Turn the
left Pedal Disc (15) for a moment.
Repeat until the console displays correct feedback.
When the reed switch is correctly adjusted, reattach
the shields, the right pedal disc, and the right Pedal
Arm (12).
MAINTENANCE AND TROUBLESHOOTING
64
41
51
70
70
41
52
52
64
64
12
415
3
58
53
52
15
17

14
HOW TO ADJUST THE DRIVE BELT
If you can feel the pedals slip while you are pedaling,
even when the resistance is adjusted to the highest
level, the drive belt may need to be adjusted.
To adjust the drive belt, you must first remove both
shields. See HOW TO ADJUST THE REED SWITCH
on page 13 and remove the shields.
Next, loosen the M8 x 22mm Flat Head Screw (65)
and turn the M10 x 60mm Button Bolt (62) until the
Drive Belt (19) is tight.
When the Drive Belt (19) is tight, tighten the M8 x
22mm Flat Head Screw (65). Then, reattach the
shields.
65
62 19

15
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
WOR OUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of
stretching. Stretching increases the flexibility of your
muscles and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
EXERCISE GUIDELINES
WARNING: Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.

16
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. eep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
1
2
3
4
5

17
NOTES

18
Specifications are subject to change without notice. For information about replacement parts, see the back cover
of this manual. *These parts are not illustrated.
ey No. Qty. Description ey No. Qty. Description
PART LIST—Model No. HRCCEL2927.2 R1209A
11Frame
21Upright
31 Left Shield
41Right Shield
52Upper Body Leg
61Left Upper Body Arm
72M10 x 74mm Button Bolt
81Right Upper Body Arm
92Stabilizer
10 2 M5 Locknut
11 1 Left Pedal Arm
12 1 Right Pedal Arm
13 1 Left Pedal
14 1 Right Pedal
15 2 Pedal Disc
16 2 Disc Crossbar
17 1 Flywheel
18 1 Shield Bracket
19 1 Drive Belt
20 2 Rear Cap
21 2 Front Cap
22 1 Idler
23 1 Console
24 2 Handgrip
25 2 M10 Bolt Set
26 1 Pivot Axle
27 4 M8 x 52mm Button Screw
28 4 M8 Split Washer
29 1 Water Bottle Holder
30 2 Large Snap Ring
31 2 Large Bearing
32 1 Pedal Axle
33 7 M10 Locknut
34 4 M10 x 75mm Carriage Bolt
35 4 M10 Washer
36 2 M3 x 16mm Screw
37 2 Pedal Arm Bushing
38 5 M8 Locknut
39 2 Inside Pedal Arm Bushing
40 2 M10 x 27mm Patch Screw
41 2 M6 x 18mm Bolt
42 6 M5 x16mm Screw
43 4 M5 Washer
44 2 Upper Body Arm Cap
45 2 M10 Split Washer
46 2 Upper Body Arm Cap
47 2 Upper Body Arm Spacer
48 2 Frame Spacer
49 6 Small Upper Body Arm Bushing
50 4 M8 x 45mm Button Bolt
51 4 M6 x 25mm Screw
52 7 M4 x 16mm Self-tapping Screw
53 1 Reed Switch/Wire
54 1 Clamp
55 2 Upper Body Arm Washer
56 2 M8 x 25mm Patch Screw
57 1 Flywheel Axle
58 1 Magnet
59 4 Console Screw
60 4 Large Upper Body Leg Bushing
61 2 3/8" x 12.7mm Hex Bolt
62 1 M10 x 60mm Button Bolt
63 2 M4 x 22mm Screw
64 4 M4 x 25mm Screw
65 1 M8 x 22mm Flat Head Screw
66 2 M6 Locknut
67 2 M5 x 14mm Self-tapping Screw
68 1 Upper Wire Harness
69 2 Wave Washer
70 4 M6 x 28mm Screw
71 4 M8 Washer
72 1 Resistance Motor
73 1 Lower Wire Harness
74 2 Pedal Arm Cap
75 1 Upright Cap
76 2 Large Wave Washer
77 1 Resistance Cable
*–Assembly Tool
*–Grease Packet
* – Userʼs Manual

19
EXPLODED DRAWING—Model No. HRCCEL2927.2 R1209A
61
30
32
31
30
31
24
8
4
3
50
5
38
45
6
46
560
17
2
33
14
12
18
19
1
33
13
11
33
51
15
70 34
9
33
33 20
20
16
61
54
52
53
38
65
62
55
56 38
50
48
47
49
24
56
55
57
35
33
58
21
21
34
60
60
60
23
52
52
64
52
41
52 41
64
49 48
47
49
49
46
16
42
25
25
25
25
15
66
66
35
67
7
45
59
9
22
44
51
35
39
37
40
28
27
39
37
35
40
27
28
49
49
26
29
63
36
36
70
68
69
69
71
71 51
51
72
43
42
43
73
10
74
74
75
76
76
77
64

Part No. 293530 R1209A Printed in China © 2009 ICON IP, Inc.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
ICON of Canada, Inc. (ICON) warrants this product to be free from defects in workmanship and material,
under normal use and service conditions. Parts are warranted for one (1) year from the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All
repairs for which warranty claims are made must be preauthorized by ICON. This warranty does not
extend to any damage to a product caused by or attributable to freight damage, abuse, misuse, improper
or abnormal usage, or repairs not provided by an ICON authorized service center; products used for com-
mercial or rental purposes; or products used as store display models. No other warranty beyond that
specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some provinces do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from province to
province.
ICON of Canada, Inc., 900 de lʼIndustrie, St. Jérôme, QC J7Y 4B8