Heart of House Hertford 343/2266 User manual

MADE IN
BRITAIN
Dimensions
Width - 86.5cm
Depth - 49cm
Height - 194cm
Hertford - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 3 - 28/01/15
Important - Please read these instructions fully before starting assembly
ALR3132
343/2266
355/3602
Issue 2 - 08/01/15 - Heart of House logo added to the front page.
Issue 3 - 28/01/15 - Width of the Back panel increased - now X1931-809.
Updated helpline number.
Note added at the end of the assembly to remove protective film.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 50kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12
3
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
8
Left Side (DF368)
(1940 x 490mm)
Right Side (DF369)
(1940 x 490mm)
Rail (DF372)
(791 x 78mm)
Left Door (DF373)
(1902 x 391mm)
Right Door (DF3136)
(1902 x 391mm)
Shelf (DF375)
(791 x 461mm)
Top (DF1470)
(791 x 482mm)
Base (DF1471)
(791 x 463mm)
Back (X1931-809)
(1931 x 809mm)
4
5
910
6
Hanging Rail (FHR785)
(785mm long)
7

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B
D E
G H I
C
Nail (F51) x 36
K
Large locking
nut (F900) x 10
Metal dowel (F901) x 10 Wooden dowel (F22) x 2
L
J
19mm Screw (F461) x 4 13mm Screw (F63) x 20
Rail Holder
(F891) x 2
Hinge plate
(F523) x 8 Hinge (F522) x 8
Handle (FSHOREDITCH) x 2
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
F
Shelf stud (F110) x 4

Finished
front edge
Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Prepare the left side
Please refer to the
drawings opposite.
You have a choice of 3
positions to fit the rail
holder . This will also
depend on which of the
2 positions you fit your
shelf.
a: To fit the rail holder
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
b: Screw 5 metal dowels
. into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit 4 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
J
E
H
E
H
Shelf
Shelf
A
A
A
A
J
J
J
J
A
H
H
E
E
A
E
E
H
E
E
H
E
E
H
1
1
Shelf
Only fit 1 rail holder
1
1
A
J
1
a:
b:
80% x 3
90% x 1

Assembly Instructions
5
Step 2
Prepare the right side
a: Fit the rail holder
into the same position as
you chose in step 1.
To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the right side .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
b: Screw 5 metal dowels
. into the right side .
Fit 4 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
E
H
E
H
H
H
E
E
E
E
H
E
E
H
E
E
H
2
2
A
J
2
Only fit 1 rail holder in the same
position as you used in Step 1
A
A
A
A
A
J
J
J
J
J
a:
b:
2
2
Prepare the top
Insert 4 large locking
nuts into the top .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
B
B
B
B
B
Step 3
B3
3
Finished
front edge
Finished
front edge
Finished
front edge

Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 4
B
A
Fit the top to the right
side
Push the top onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
3
B
B
3
Fit the base
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
2
4
B
4
B
E
2
3
Prepare the base
Insert 4 large locking
nuts into the base .
B
B
B
B
Step 5
Step 6
B44
Finished
front edge
4
2

Finished
front edge
Assembly Instructions
7
Step 7
Step 9
2
C
C
10mm
C
Prepare the rail
Insert 2 large locking
nuts into the rail .
Tap 2 wooden dowels
into the rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
B
B
B
6
6
Finished
front edge
C
6
Finished
front edge
6
Fit the rail
Push the rail onto the
right side .
Use a screwdriver to
tighten the large locking
nut fitted to the rail
. .
2
6
B
6
Step 8
Note: Support the rail
until the left side has been
fitted in the next step.
6
1
3
4
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the top , base and
rail .
1
B
3 4
6

yy
yy
Assembly Instructions
8
Step 10
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Carefully stand the
unit up for the next
step.
10
G
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
xx
xx
G
10
Step 11
7
H
Fit the hanging rail
Push the hanging rail
into the rail holders
fitted to the side panels.
Note: You may have
chosen a different hanging
rail position to the one
shown.
7
H
7
Warning: The
unit is heavy.
Lift with care.

Assembly Instructions
9
Step 12
Step 13
Fx 4
Fit the shelf
Insert 4 shelf studs at
the required position.
Lower the shelf down
onto the shelf studs .
Note: You may have
chosen a different shelf
position to the one
shown.
5
F
F
5
Prepare the 2 doors
Push fit 4 hinges into
each of the 2 doors
and .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
E
K
8
9
K
E
E
90
K
K
E
E
K
E
E
K
E
E
K
E
E
K
E
E
K
E
E
K
E
E
8
9

Assembly Instructions
10
Step 14
Fit doors and handles
Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door and
using screws .
K
K
K
J
J
J
K
J
L
D
8
9
8 9
a: b:
c: d:
J
K
J
J
B
J
K
K
K
A
K
J
B
e:
D
D
L
L
8
9
Warning: The
doors are heavy.
Lift with care.

Assembly Instructions
9
Step 15
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C

Assembly Instructions
12
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 16
Fit the overbalance
protector
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Assembly is complete
I
I
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
I
Strap
Washer
Screw
TOP OF UNIT
I
Note: Now the assembly has finished you can
remove any protective film from the doors.

ALR3132