Heart of House Westbury 397/7611 User manual

Westbury - Dresser Unit
Dimensions
Width - 90.4cm
Depth - 42.2cm
Height - 188.2cm
BK04800 - Issue 1 - 25/03/2015
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6403030
Assembly Instructions - Please keep for future reference 397/7611
391/1512
424/8002

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Due to difference in floor
levels, doors may not be
aligned. Adjustment may be
necessary.
• Do not use extended drawers
to aid standing. Do not stand on
extended drawers.
• Do not over load drawers,
the maximum load per drawer
should not exceed 3kg
• To prevent bowing of shelves
do not over load, and always
distribute weight evenly.
• If a residual aroma is
experienced with your new
furniture after the packaging
is removed simply ensure the
room is well ventilated and this
will assist a speedy removal
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• It is essential that this unit be
fixed to a wall with the fittings
provided.
• Please retain the product label
on the back of the unit, as this
information will help support any
queries.
• Dust with a clean cloth or, if
required a slightly damp cool
cloth. Do not use household
cleaners, abrasives or polishes
as permanent damage may
occur.
• Your furniture is finished to the
required colour. Avoid exposure
to strong sunlight as this can
change the colour. Change in
appearence may also occur if
items are permanently left on a
surface.
• Do not drag the furniture or lift
it by its top.
• Avoid sharp objects, contact
with water and direct heat on all
surfaces
• From time to time check that
there are no loose screws on
this unit.
• You should get assistance
when moving or lifting your
furniture. Furniture consisting of
more than one unit should be
disassembled before attempting
to move it.
• Doors and drawers should
be secured or removed before
moving.
• Electrical fittings must be fitted
with a 3-amp fuse to BS1362.
Disconnect from the source of
power before changing bulbs.
Replace bulbs with the same
type and wattage.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance - Non compliance with this information may affect your guarantee

Components - Panels
Please check you have all the panels listed below
2
Display Base (77.7 x 90.4 x 42.2cm)
2
Display top (110.5 x 90.4 x 32.6cm)
1
If you have damaged or missing components,
call the Customer Helpline:
0345 6403030

3
Please check you have all the fittings listed below
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings
Tools required
A
E
B C
D
Phillips screwdriver
(medium)
15mm Screw x 1 15mm Washer x 2 Wall strap x 1
The following components are pre-fitted and are illustrated for reference only.
Knob handle x 6 20mm Handle screw x 6 Display light [with bulb] x 1
F
Multi socket adapter x 1
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
12mm Screw x 4 Connecting bracket x2
Step Ladder
(or equivalent)

4
Assembly Instructions
Step 1
Joining the Top to the
Base
a: Position display base
2slightly away from
the wall in the position
required [please note it
will be hard to move once
assembled]. When in
place sit the display top
1on top of the display
base 2and align the
backs of the two units
and centralize the top on
the base.
b: Take one of the
connecting brackets
Hand a 12mm screw
G and using philips
screwdriver fix the plate
to the top of the base unit
and then to the bottom of
the top unit.
Repeat bon the other
side of the unit.
1
2
a:
Step 2
b:
2
1
Philips screwdriver
4
Assembly Instructions
FE

Assembly Instructions
Step 2
5
Philips screwdriver
20mm handle screw
Knob handle
Philips screwdriver
20mm handle screw
Remove and replace
handle
a: The knob handles
are fitted to the inside of
the unit, using a Philips
screwdriver unscrew the
20mm handle screws in
each handle and remove
both the 20mm handle
screw and the knob
handle.
b: Replace the knob
handle on the front of
the unit. Fix in position
by screwing the 20mm
handle screw into each
handle from inside the
unit using a Philips
screwdriver.
a:
b:
2
1
2
1
Knob handle
Assembly Instructions

E
6
Assembly Instructions
Step 3
Connecting display
lights
a: The display light is
fixed to the light pelmet
inside the display
cabinet. Push the the
fitting on the end of the
cable through the hole in
the back panel.
connection from display light
1
a:
b:
b: Connect the socket on
the display light into the
connection on the multi
socket adapter D. You
can now connect to the
mains.
Note: the light display
light fitting has is own on
/ off switch on the back of
the fitting
Warning:
Always turn the
lights of at the
mains when changing the
bulb.
D
Connection from display light
Assembly Instructions

Assembly Instructions
Step 4
Fixing to wall
It is recommended that
the unit is fixed to a wall
Fix wall strap Cto the
back of the unit using
15mm screw Aand
15mm washer B.
Warning: The
15mm screw A
is for fixing the
wall strap Cto furniture
only. In addition to this
you will need to choose
a screw or fitting which is
suitable for securing the
wall strap Cto the type
of walls you have. If you
are unsure about what
type of screw to use seek
professional help.
Assembly is complete.
7
CUsing the correct type of
screw, screw through the
washer and wall strap
into a pre-drilled hole in
the wall
Back Panel
Unit Top
A
B

If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6403030
8