Heart of House 413/6633 User manual

Bergen 180 High gloss doors
Dimensions
Assembly Instructions- Please keep for future reference
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
DR825080
Issue 1 - 27/05/15
Important–Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
413/6633 HIGHGLOSS WHITE
417/7537 HIGHGLOSS CASH
High gloss doors
417/7537
413/6633
1
2
1
Dimensions
Width - 180cm
Depth - 6.7cm
Height - 195.2cm
1
2
1

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
Safety and Care Advice
Important – Please read these instructionsfully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
•To reduce the
likelihood of
damaging your
product please
ensure that your
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
power drill is set on a low torque
setting.
• Remove all fittings from the
unit or your floor.
to its final position (in the same

3
Cabinet supplied separately
226/8730
248/6921
249/4834
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing parts, call the
Customer Helpline:
03456 400 800
Segment middle x2
(91.5 x 65cm)
2
P3356
Segment x4
(91.5 x 65cm)
1
P3355

Screw x 33 (4x15mm)
AC ZF9997L
Front guide part x 2
AI ZF9997C
Sliding door connecting plate x 2
AK ZF9997B
Sliding door connecting bracket x 2
AL ZF9997A
Back guide part x 2
AJ ZF9998D
A
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Ruler- Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Phillips screwdriver
(medium & large)
Flatblade screwdriver
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or drill)
5mm Suitable drill bit
5mm Suitable drill bit
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Stairs
Piercer Scissors
(medium)
(small)
Spirit level
Setsquare
4
Plug, Nylon x 32 (5x9mm)
EFK1082
Screw x 72 (4x12.5mm)
DFK1309
Connecting plate x 8
OFK1236
Brush x 3 (1951mm)
TPM1652C
Door trim x 1 (1951mm)
UPM1652D
Door handle x 3 (1951mm)
SPM1652B
Spacer x 1
AE ZF9997F

1
1
1
2
1
1
2
1
Assembly Instructions
Step 2
3 Segment slide door left
a: Put 8x nylon plug E
into the segment 1.
Use a small hammer.
Repeat this step.
c: Mount segment middle
2with 3x screws Don
door trim U.
Mount segment 1with
4x screws Don
door trim U.
b: Mount door trim Uwith
3x screws Don segment
1.
Note: there should be no
gap between doorsegment
1and door trim U.
d: Mount door handle S
on segment 1with 4x
screws Dand on middle
segment 2with 3x
screws D.
Note: there should be no
gap between doorsegment
1and door handle S.
a:
2x
No Gap
between metal profiles
and door panel!
5
E
E
b:
c:
d:
U
U
S
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D

Assembly Instructions
Step 2
3 Segment slide door left
e: Mount 4x connecting
plate O, each with 2x
screws Don segment
1and 2x screws Don
middle segment 2.
Remove protective film
from door handle S.
Stick 1x brush Tonto
door handle Sby partially
removing the cover from
adhease as brush is
applied.
f: Upside.
Mount 2x Sliding door
connecting plate k
squarely by using the
guidemarks in the plate
k, each with 6x screws
con segment 1.
Attach 1x spacer ewith
1x screw con the
brush side sliding door
connecting plate k.
g: Underside.
Mount 2x back guide
part j, each with 2x
screws con segment 1.
1
1
2
1
1
Please remove
the protective film!
S
T
AC
x2
AJ
AC
AK
AK
AC
AC
AC
AC
AC
AJ
AJ
AC
AC
AC
AC
e:
f:
g:
6
T
O
O
D
D
D
D
S
AE
O
O
D
D
D
D

1
2
1
Assembly Instructions
Step 3
Place left slide door
2 People are required for
step 3a and 3b.
a: Hook the 2x back guide
part jinto the plastic
guide rail R.
a: Detail.
The hook of the back guide
part jshould be in the
front guide of the plastic
guide rail R
a:
7
AJ
AJ
R
R
R

Assembly Instructions
Step 3
Place left slide door
b: Hook Sliding door
connecting platek
on metal guide rail Q.
b: Detail.
The wheel of the sliding
door connecting plate k
should be in the front
guide of the metal guide
rail Q.
To lock the door, lock the
Sliding door connecting
plate kon the guide
railQwith the locking pawl.
8
1
2
1
push the yellow
lock pin to
secure part kto rail
b:
Q
Q
Q
Q
AK
AK
AK

Assembly Instructions
Step 4
3 Segment slide door right
a: Put 8x nylo
the segment 1.
Use a small hammer.
Repeat this step.
c: Mount segment middle
2with 3x screws Don
door handle S.
Mount segment 1with
4x screws Don door
handle S.
b: Mount door handle S
with 4x screws Don
segment 1.
Note: there should be no
gap between doorsegment
1and door handle S.
(see �).
d: Mount door handle S
on segment 1with 4x
screws Dand on middle
segment 2with
3x screws D.
Note: there should be no
gap between doorsegment
1and door handle S.
(see �).
9
1
1
2
1
1
1
2
1
a:
E
E
c:
d:
S
S
S
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
2x
b:
No Gap
between metal profiles
and door panel!
Step 4
3 Segment slide door right
a: Put 8x nylon plug E
into
the segment 3.
Use a small hammer.
Repeat this step.
c: Mount segment middle
4with 3x screws Don
door handle S.
Mount segment 3with
4x screws Don door
handle S.
b: Mount door handle S
with 4x screws Don
segment 3.
Note: there should be no
gap between doorsegment
3and door handle S.
d: Mount door handle S
on segment 3with 4x
screws Dand on middle
segment 4with
3x screws D.
Note: there should be no
gap between doorsegment
3and door handle S.

Assembly Instructions
Step 4
g: Underside.
Mount 2x front guide
part i, each with 2x
screws con
segment 1.
10
1
1
2
1
1
T
O
O
D
D
D
D
S
O
O
D
D
D
D
T
Please remove
the protective film!
S
T
AC
AC
AC
AC
AC
AC
AC
AC
e:
f:
g:
AL
AL
AI
AI
x2
AC
AI
Step 4
3 Segment slide door
right
e: Mount 4x connecting
plate O, each with 2x
screws Don
segment 3and
2x screws Don middle
segment 4.
Remove protective film
from door handle S.
Stick 2x brush Tonto 2x
door handle Sby partially
remove the cover from
adhease as brush is
applied.
f: Upside.
Mount 2x sliding door
connecting bracket l
squarely by using the
guidemarks in the plate
l,
each with 6x screws c
on segment 3.
g: Underside.
Mount 2x front guide
part i, each with 2x
screws con
segment 3

Assembly Instructions
Step 5
Place right slide door
a: Hook the 2x front guide
part iinto the plastic
guide rail R.
a: Detail.
The hook of the rear guide
part ishould be in the
front guide of the plastic
guide rail R
a:
11
R
R
AI
R
1
1
2

Assembly Instructions
Step 5
Place right slide door
b: Hook the sliding door
connecting bracketl
on metal guide rail Q.
b: Detail.
The wheel of the sliding
door connecting bracket
lshould be in the rear
guide of the metal guide
rail Q.
To lock the door, lock the
sliding door connecting
bracket lon the
guide rail Qwith the
locking pawl.
12
a:
Q
Q
Q
Q
AL
AL
AL
1
1
2