BDI ciao 1170 User manual

1
Ciao is engineered for easy assembly. Carefully follow this
procedure to prevent any damage.
Placement and Maintenance
Ciao is designed for indoor use on level floors. Clean wood veneer
with a moist cloth.
Step 1
Unpack and identify the components at left. The assembly
workspace should be a non-marring surface such as carpet. For
missing hardware pieces, please contact BDI Customer Service
at [email protected]. For all other concerns, please
contact your BDI Retailer.
Component List
Designed by Matthew Weatherly.
These distinctive product congurations are protected by US and
international patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2015, BDI
Made in China. 1170REV10202015v1
A - Phillips Screwdriver
x 1
ciao
1170
console
assembly instructions
bdiusa.com [email protected]
C - Toggle Bolt package
x 1 Package
(2 toggles and screws
with each package)
D - Dry wall anchor
x 2
E - Wall Cleat
x 1
I - Screw
x 2
F - Screw
x 4
J - Washer
x 4
B - Wall Template
x 1
G - Leg
x 1
K - Composite Glass Top
x 1
H - Console
x 1
Step 2
Position the Wall Template (B) in the desired console
location. Using a pencil, mark the wall as shown in
the diagram above, tracing the two slot locations near
top of template and the left & right hole locations near
bottom. Mark a hole location at center of each traced
slot.

2assembly instructions
bdiusa.com [email protected]
ciao
1170 console
Step 3
Install Toggle Bolts (C) and Dry Wall Anchors
(D) as shown.
C x 2
D x 2
Step 4
Using a 1/2" drill bit, drill both
marked holes.
Step 7
While holding the toggle anchor
with one hand, push the collar
towards the wall.
Step 5
Position the metal end of the
toggle anchor as shown.
Step 8
The collar is pushed all the way
into the hole.
Step 6
Pull toggle anchor back to
engage.
Step 9
Break off both plastic ends.

3assembly instructions
bdiusa.com [email protected]
ciao
1170 console
Step 11
Using Screws from Toggle Bolt (C) package and
Washers (J), secure Wall Cleat (E) into installed
Toggle Bolts (C).
Step 12 (optional)
Using Screw (F), attach Metal Leg (G), to Console (H) with Phillips
Screwdriver (A). Do not overtighten.
E
C
C
J
J
H
Step 10
The toggle anchor is set.

4assembly instructions
bdiusa.com [email protected]
ciao
1170 console
Step 14
Secure Console (H) to wall using Screw (I),
Washer (J) and Phillips Screwdriver (A).
Do not overtighten.
Step 15
Place Glass Top (K) on top of console.
Step 13A (with legs) or Step 13B (without legs)
With the help from another person, position the cabinet upright and
place Console (H) onto Wall Cleat (E).
H
H H
E E
I
J
K

1
Ciao is engineered for easy assembly. Carefully follow this
procedure to prevent any damage.
Placement and Maintenance
Ciao is designed for indoor use. Clean wood veneer with a
moist cloth
Step 1
Unpack and Identify
The assembly workspace should be a non-marring surface
such as carpet. For missing hardware pieces, please contact
BDI Customer Service at [email protected]. For
all other concerns, please contact your BDI Retailer.
If you are installing the Ciao mirror with the Ciao console
proceed to Step 2. If you are installing the Ciao mirror by
itself, skip to Step 13.
Component List
Designed by Matthew Weatherly.
These distinctive product congurations are protected by US and
international patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2015, BDI
Made in China. 4972REV10202015v1
ciao
4972
mirror
assembly instructions
bdiusa.com [email protected]
C - Mirror Frame
x 1
G - Mirror
x 1
A - Toggle Bolt package
x 1 Package
(2 toggles and screws
with each package)
B - Dry wall anchor
x 1
E - Screw
x 1
F - Washer
x 3 This template
is included with
Ciao 1170.
Step 2
Installation with Ciao 1170
Position the Wall Template in the desired location above the
console. Align edges of Wall Template with sides of cabinet.
Using a pencil, mark the hole positions shown in the diagram
below.