Hearth & Home GFK10 Fan Kit User manual

Hearth & Home Technologies • GFK10 Fan Kit • 4016-136 • Rev F • 12/17 1
Description Part Number Qty
Fan 1
Electrical Cord 1
Fan Shield 4049-238 1
Air Deector 4058-193 1
Control Module 4021-708 1
Fastener Pack 4016-048 1
Foam Tape 4021-655 2
Magnetic Tape 4021-654 2
Jumper Wire (blue) 1
tm
Models:
GFK10 Fan Kit
Installation
Instructions
Note: You may not need all parts included with this kit.
Table 1 Contents of Carton
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accesso-
ries with this appliance. Using non-listed accessories could
result in a safety hazard and will void the warranty.
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA 70-
latest edition or the Canadian Electric Code CSA C22.1
WARNING! Risk of Shock or Explosion! DO NOT wire IPI
controlled appliance junction box to a switched circuit. Incor-
rect wiring will override IPI safety lockout.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear
protective gloves and safety glasses during installation.
Sheet metal edges are sharp.
Check Contents of Shipping Carton
Compare contents of carton in Table 1 with the actual parts
received. If any parts are missing or damaged, contact your
dealer before starting installation. Do not install a damaged
fan kit.
The GFK10 Fan Kit has been designed to circulate room air through the appliance to enhance heat output. The fan kit oper-
ates on 120VAC, 60 Hz power. This is available through a receptacle in the factory-installed junction box. The junction box
is located in the controls compartment of the appliance.
A control module is provided with the fan kit which automatically turns the fan on and o󰀨 at preset times and is equipped wth
a variable speed control to provide a quiet forced air ow at the desired speeds.
Check with your local building code agency before you begin installation to ensure compliance with local codes, including
the need for permits and follow-up inspections. If you encounter any problems regarding code approvals, or if you need
clarication of any of the instructions contained here, contact your Hearth & Home Technologies Inc. dealer. For the dealer
nearest you, please visit www.hearthnhome.com.
Installation Precautions
The GFK10 Fan Kit is tested and safe when installed in ac-
cordance with this installation manual. It is your responsibil-
ity to read all instructions before starting installation and to
follow these instructions carefully during installation to as-
sure maximum benet from, and safe operation of, the fan.
►

Hearth & Home Technologies • GFK10 Fan Kit • 4016-136 • Rev F • 12/17
2
Figure 3
Figure 2
Magnetic
Tape
Foam
Figure 4
Secure with 4 screws
Figure 6
Figure 1
1. Fan Assembly
• Bend hand brakes of fan bracket as shown in Figure 1.
• Attach fan bracket by hooking hand brakes into open end
of fan as shown in Figure 2. Crimp down tight with pliers
so tabs do not interfere with rotor blades.
• Secure bracket to fan with two screws as shown in
Figure 3.
• Cut foam tape into two equal pieces.
• Apply magnetic tape and foam to fan bracket as shown
in Figure 4.
• Secure the air deector with four screws as shown in
Figure 6.
• Attach power supply cord to terminals of fan motor. Attach
ground wire to fan body with screw.
Figure 5
Note: The next two steps apply only if installing in the
Aveo:
• Locate air deector and hand brake ends as shown in
Figure 5.
The following steps apply to all installations:

Hearth & Home Technologies • GFK10 Fan Kit • 4016-136 • Rev F • 12/17 3
2. Install the Fan
• Position the fan all the way to the rear and center in the
appliance.
Aluminum Plate
Fan
Inner
Shell
Outer
Shell
Figure 7 Eclipse - Position Fan
3. Wiring the Fan Control Module - DEXEN VALVE (IPI) *
Dexen
Valve
Fan
Control
Module
Green Wire from Ignition Control
Black
Black/White
Black
Red
White
Ground
Figure10 - Dexen (IPI) Wiring Diagram
Fan
Aluminum Plate
Figure 9 Aveo - Position Fan
Inner Shell
Outer Shell
Figure 8 Eclipse - Tilt Fan
• Make sure fan motor is centered over aluminum plate on
bottom pan. See Figures 7 and 9.
Eclipse only: Tip and rotate the fan (Figure 8) so the exhaust
end of fan is between inner and outer shell.
• Plug the fan cord into the junction box outlet labeled
“FAN.”
- Connect the black with white stripe wire with 3/16 in.
piggyback connector from fan control module to valve.
- Connect green ignition control wire to piggyback connector
on black with white stripe fan control module wire.
- Connect the black, white and red wires with 1/4 in. female
connectors from fan control module to appliance junction
box as shown in Figure 10.
- Connect the black ground wire to the appliance.
- Remove the green ignition control wire from the valve.
* INCLUDES INTELLIFIRE-PLUS WHEN USING RC100. FAN TIMER NOT LISTED WITH RC200 OR RC300.


Hearth & Home Technologies • GFK10 Fan Kit • 4016-136 • Rev F • 12/17
4
5. Recommended Fan Control Set-up Procedure
Note: The test sequence works only during the first
(approximately) seven minutes after power-up.
With burner and pilot extinguished:
• Turn control knob clockwise to activate control.
• Press and hold test button on the control module.
- Fan will turn on.
- Adjust fan speed to the desired speed using the control
knob.
- Release test button. Fan will stop.
• Fan control is now fully operational and will operate
automatically each time appliance is used.
• Operates with APPROXIMATELY a 7-minute delay to turn
on and a 12-minute delay to turn o󰀨.
4. Wiring the Fan Control Module - SIT VALVE
- Connect the black, white and red wires with 1/4 in. female
connectors from fan control module to appliance junction
box as shown in Figure 11.
- Connect the black ground wire with the ring terminal to
the TP screw on the valve (center).
- Connect blue jumper wire between fan control wire (black
with white stripe) and valve. Plug 1/4 in. female end of
blue jumper wire to the back side of valve wiring block
marked TH.
Wall
Switch
SIT
Valve
TP TH
TH
TP
Fan
Control
Module
Black/White
Black
Black
Red
White
Thermopile
Red
White
Blue
Ground
Figure 11 - SIT Wiring Diagram