Heat & Glo 6000TRS-CE Assembly instructions

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/131
Model:
6000TRS-CE
Installers Guide
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS INSTALLERS
GUIDE MUST BE LEFT WITH APPLIANCE FOR FUTURE
REFERENCE.
Please contact your Heat & Glo dealer with any questions or
concerns. For the number of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
Printed in U.S.A. Copyright 2013
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044, USA
0086
This is a room sealed appliance and no other ventilation is
required than what is provided.
These instructions are only valid if the following country symbol is
on the appliance. If this symbol is not present on the appliance,
it is necessary to refer to the technical instructions which will
provide the necessary information concerning the modication
of the appliance to the conditions of use for the country.
These instructions are valid for the following countries: GB, IE
WARNING
This appliance has been supplied with an integral barrier


HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high temperatures.

materials.
• Keep clothing, furniture, draperies and other ammable
materials away.
• Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of
this or any other appliance.
 
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
- If you cannot reach your gas supplier, call
the re department.
• Installation and service must be performed
by a qualied installer, service agency, or the
gas supplier.




This product is covered by one or more of the following patents: (United States) 5601073, 5613487, 5647340, 5890485, 5941237, 6006743, 6019099, 6053165,
6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending.
2000-945B


Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/132
!
This appliance is intended for use on a gas installation with a governed meter.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
SAFETY AND WARNING INFORMATION
READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE
these installation instructions may result in a possible re hazard and will
void the warranty.
Prior to the rst ring of the replace, READ the Using Your Fireplace section of the Users
Guide.
this appliance if any part has been under water. Immediately CALL a qualied
service technician to inspect the unit and to replace any part of the control system and any
gas control which has been under water.

Installation and repair should be by a qualied service person. The appliance
and ue system should be INSPECTED before initial use and at least annually by a
professional service person.
Always KEEP the appliance clear and free from combustible materials, petrol, and other
ammable vapors and liquids.
  the ow of combustion and ventilation air. Keep the front of the
appliance CLEAR of all obstacles and materials for servicing and proper operations.
Due to the high temperature, the appliance should be out of trafc areas and
away from furniture and draperies. Clothing or ammable material   
PLACED on or near the appliance.
Children and adults should be ALERTED to the hazards of high surface temperature
and should STAY AWAY to avoid burns or clothing ignition. Young children should be
CAREFULLY SUPERVISED when they are in the same room as the appliance.
These units use one of the uing systems described in the Installing the Fireplace
section of the Installers Guide. ue systems or components .
This gas appliance and ue assembly be vented directly to the outside and 
NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas
appliance a separate ue system. Common ue systems are .
INSPECT the external terminal cap on a regular basis to make sure that no debris is
interfering with the air ow.
The glass door assembly be in place and sealed, and the trim door assembly 
be in place on the appliance before the unit can be placed into safe operation.
   this appliance with the glass door removed, cracked, or broken.
Replacement of the glass door should be performed by a licensed or qualied service
person. strike or slam the glass door.
The glass door assembly be replaced as a complete unit, as supplied by the
gas appliance manufacturer. material may be used.
abrasive cleaners on the glass door assembly. to clean
the glass door when it is hot.
Turn off the gas before servicing this appliance. It is recommended that a qualied service
technician perform an appliance check-up at the beginning of each heating season.
Any safety screen or guard removed for servicing must be replaced before operating
this appliance.

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 3

Contents
 ...................................2
Service Parts List ...........................................................4
Section 1: Approvals and Regulations.........................7
Appliance Certication ..................................................7
Installation Regulations ................................................7
Section 2: Getting Started .............................................8
Introducing the Heat & Glo Gas Fireplaces ..................8
Pre-installation Preparation ..........................................8
Section 3: Installing the Fireplace ..............................10
Step 1 Locating the Fireplace ..................................10
Step 2 Framing the Fireplace ...................................11
Step 3 Installing the Flue System .............................12
A. Flue System Approvals .............................12
B. Installing Flue Components ......................20
C. Flue Termination .......................................24
Step 4 Positioning, Leveling and
Securing the Fireplace ..................................29
Step 5 The Gas Control Systems .............................29
Step 6 The Gas Supply Line ....................................30
Step 7 Gas Pressure Requirements ........................31
Step 8 Wiring the Fireplace ......................................31
Step 9 Finishing .......................................................32
Step 10
Installing Trim, Logs & Ember Material ............33
Installing the Trim ..........................................33
Positioning the Logs .....................................34
Placing the Ember Material ...........................36
Step 11 Before Lighting the Fireplace ........................37
Step 12 Lighting the Fireplace ...................................38
After the Installation .....................................38
Section 4: Maintaining and Servicing
Your Fireplace ............................................39
Section 5: Troubleshooting .........................................41
Limited Lifetime Warranty ...............................................44
 = Contains updated information.


Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/134
Service Parts 6000TRS-CE


8
6
7
9
10
11
12
13
14
15
16
17
18
19
Part number list on following page.
Log Set Assembly
4
235
1
36” Gas Fireplace - DV
03/13

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 5
Service Parts 6000TRS-CE


IMPORTANT THIS IS DATED INFORMATION: When requesting service or replacement parts for your appliance please
provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
ITEM DESCRIPTION COMMENTS PART NUMBER
Log Set Assembly LOGS-6TRSCE
1Log #1 SRV2049-700
2Log #2 SRV2049-701
3Log #3 SRV385-723
4Log #4 SRV385-721
5Log #5 SRV385-722
6Junction Box 546-250A
Refractory Kit BRICK-6000-FB
7Refractory, Right SRV2027-372
8Refractory, Back SRV2027-370
9Refractory, Left SRV2027-371
10 Exhaust Bafe 2049-101
11 Grate 2049-020
12
Burner Assembly N 2049-010
Burner Assembly P 2049-012
Burner Assembly B 2049-014
13 Base Refractory 2049-102
14 Glass Door Assembly GLA-6TRXI
15 Insulation Board 385-401
16 Surround Pre Aug 2009 SRV2101-260
Post Aug 2009 2166-019
17 Top Louver 392-182A
18 Dress Guard 392-180A
19 Hood SRV60-143-BK
Gasket Assembly
2166-081
Contains Burner neck, shutter bracket, vent, seal cap, and valve
plate gaskets
Glass Latch Assembly Pkg of 2 33858/2
High Temp Limit Switch 046-018A
Exhaust Restrictor 530-299
Mineral Wool 050-721
Touch-Up Paint TUP-GBK-12
Additional service part numbers appear on following page.

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/136
Service Parts 6000TRS-CE


#20 Valve Assembly
IMPORTANT THIS IS DATED INFORMATION: When requesting service or replacement parts for your appliance please
provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
ITEM DESCRIPTION COMMENTS PART NUMBER
20.1 Pilot Assembly N 529-550A
Pilot Assembly P/B 529-551A
20.2 Pilot Bracket 2049-105
20.3
Ori ce N (#33C) 582-833
Ori ce P (1.8 MM) 582-818
Ori ce B (#52C) 582-852
20.4 12" Flex 383-302A
20.5 Valve Bracket 2118-104
20.6 Flex Assembly 302-330A
20.7 Piezo Ignitor 291-513
20.8 Wire Assembly 049-552A
20.9 On/ Off Rocker Switch 060-521A
20.10 Valve N 060-524
Valve P 060-526
20.11 Male Connector Pkg of 5 303-315/5
Conversion Kits
Natural to Propane NGK-6TRS-CE
Propane to Butane LPK-6TRS-CE
Butane to Propane BGK-6TRS-CE
Regulator N 230-1570
Regulator P/B 230-1520
Pilot Ori ce N 529-512
Pilot Ori ce P/ B 200-2630
20.1
20.2
20.3
20.4
20.5
20.6
20.7
20.8
20.9
20.10 20.11

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 7
1
Approvals
and
Regulations

The Heat & Glo replace models discussed in this
Installers Guide have been tested to certication
standards and listed by the applicable laboratories.
Installation Regulations
Before installation check that local distribution conditions, nature of gas and
pressure, and adjustment of the appliance are compatible.
This appliance must be installed with the rules in force, and used only in a
sufciently ventilated space. Consult instructions before installation and use of
this appliance.
MODEL LABORATORY TYPE CERTIFICATION STANDARD
6000TRS-CE BSI Gas Fireplace BS EN 613:2001 (Amd 1)

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/138
Heat & Glo direct ue gas replaces are designed to
operate with all combustion air siphoned from outside
of the building and all exhaust gases expelled to the
outside.
The information contained in this Installers Guide,
unless noted otherwise, applies to all models and gas
control systems.
Gas replace diagrams, including the dimensions, are
shown in this section.
This gas replace and its components are tested and
safe when installed in accordance with this Installers
Guide. Report to your dealer any parts damaged in
shipment, particularly the condition of the glass. Do

substitute parts.
The flue system components and trim doors are
shipped in separate packages. The gas logs are
packaged separately and must be eld installed.
       
    

      
will void the owner’s warranty and may present

The Heat & Glo Fireplace Products, Inc. Warranty
will be voided by, and Heat & Glo Fireplace Products,
Inc. disclaims any responsibility for, the following
actions:
• Installation of any damaged replace or ue system
component.
• Modication of the replace or direct ue system.
• Installation other than as instructed by Heat & Glo
Fireplace Products, Inc.
• Improper positioning of the gas logs or the glass
door.
• Installation and/or use of any component part not
manufactured and approved by Heat & Glo Fireplace
Products, Inc., not withstanding any independent
testing laboratory or other party approval of such
component part or accessory.
ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE
HAZARD.
Introducing the
Heat & Glo
Gas Fireplaces
Pre-installation
Preparation
2
Getting
Started

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 9

When planning a replace installation, it’s necessary to determine:
• Where the unit is to be installed.
• The ue system conguration to be used.
• Gas supply piping.
• Electrical wiring.
• Framing and nishing details.
• Whether optional accessories—devices such as a fan, wall switch, or remote control—are
desired.
If the replace is to be installed on carpeting or tile, or on any combustible material other
than wood ooring, the replace should be installed on a metal or wood panel that extends
the full width and depth of the replace.
A
B
CD
E
FRONT VIEW
TOP VIEW
LEFT SIDE RIGHT SIDE
F
G
H
I
J
K
L
M
O
P
GAS LINE
ACCESS
Q
R
N
C
L
C
L
Location Centimeters
J54,6
K 29,7
L 72,4
M 36,2
N 21,6
O 73
P21,6
Q25
R 91,8
Location Centimeters
A 104,1
B 91,8
C 85,1
D 87,9
E57
F 24,6
G68,3
H15,2 dia
I 101,9

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/1310

3
Installing the
Fireplace
The diagram below shows space and clearance
requirements for locating a replace within a room.
Step 1
Locating the
Fireplace

The top and back of the replace are dened by stand-offs.
The minimum clearance to a perpendicular wall extending past the face of the replace is
7.62 cm.
The back of the replaces may be recessed into combustible construction (see Figure 3).
MODEL: 6000TRS-CE RECESSED DEPTH: 54.6 cm
Figure 3. Minimum Clearances

For Horizontal Sections For Vertical
Sections

Top Bottom Sides Top Bottom Sides
7.6 cm 2.54 cm 2.54 cm 2.54 cm 6.4 cm 1.3 cm 2.54 cm

Glass
Front Floor  Fireplace

Fireplace

Fireplace Ceiling
91.4 cm 0 1.3 cm 1.3 cm 8.9 cm 79 cm
REAR FLUE,
HORIZONTAL TERMINATION
TWO 90º ELBOWS REAR FLUE
NO ELBOWS
REAR FLUE
ONE 90º ELBOW
ALCOVE
INSTALLATION
TOP FLUE
ONE 90º ELBOW
A
BC
B
E
B
B
B
D
D
F
G
H
D
A
D
NOTE: THE REAR STANDOFF MAY NEED
TO BE REMOVED WHEN VENTING AT 45º
1,3 cm
I
C
L
A B C D E F G H I
cm 130 107 183 144 See Section F.
Mantel Projections 56 45 20 73

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 11
Framing should be
constructed of 2 X 4
lumber or heavier.
* Note: Dimension B taken from n-
ished hearth frame. Dimensions D
and E taken from bottom of unit.
A
B
C
*
A B C D E
107 cm 102 cm 56 cm 68,3 cm 106 cm
Figure 4. Framing Dimensions

Step 2
Framing the
Fireplace

   
   

Fireplace framing can be built before or after the replace is
set in place. Framing should be positioned to accommodate
wall coverings and replace facing material. The diagram
below shows framing reference dimensions.
14 cm
8 cm
NON-COMBUSTIBLE ZONE
IS DEFINED BY 8 CM ABOVE
THE ELBOW FOR THE ENTIRE
WIDTH AND DEPTH (BEHIND
THE FRONT HEADER) OF
THE FIREBOX.
WALL
STUD
E*
D*

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/1312
HORIZONTAL
TERMINATION
WALL FIRESTOP
90 DEGREE
ELBOW
VERTICAL
TERMINATION
STORM COLLAR
ROOF FLASHING
HORIZONTAL PIPE
SUPPORT
PIPE LENGTH
WALL BRACKET
CEILING
FIRESTOP
DVP-SERIES
DVP-TRAP
DVP-TVHW
FLUE SYSTEM TERMINATION KITS
Figure 5. Flue Components and Terminations
A. Flue System Approvals
These models have ue starting collars on both the top and
the back of the unit. Depending upon the installation, decide
which ONE set of starting collars will be used to attached the
ue system. The starting collar sealing cap must remain on the
starting collar NOT used.
These models use DVP-series direct ue components when
using the TOP and REAR ue collars.
Approved ue system components are labeled for identication.
NO OTHER FLUEING SYSTEMS OR COMPONENTS MAY
BE USED. Detailed installation instructions are included with
each ue termination kit and should be used in conjunction with
this Installers Guide. Figure 4 shows ue system components
and terminations.

The ue systems installed on this gas replace may include one,
two, or three 90°elbow assemblies. The relationships of vertical
rise to horizontal run in ue congurations using 90° elbows
MUST BE strictly adhered to. The rise to run relationships are shown
in the ueing drawings and tables on the next several pages.
Note: Two 45° elbows may be used in place of one 90° elbow.
You MUST always maintain the MAXIMUM and MINIMUM rise-
to-run ratios in the ue system when using 45° elbows.
Step 3
Installing the
Flue System

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 13

NOTE: PIPES OVERLAP 3,2 cm AT EACH JOINT.
DVP90ST
31.9 cm
28.6 cm
18.4 cm
3.2 cm TYP
1.3 cm TYP
21.7 cm
DVP36
DVP48
121.9 cm
61.0 cm
91.4 cm
10.2 cm
15.2 cm
DVP4
DVP6
30.5 cm
DVP12
5.1 cm
MIN.
DVP12A
31.0 cm
MAX.
DVP24
DVP45
36.2 cm
25.1 cm
20.3 cm
45.0º
26 cm
26 cm

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/1314
STRAIGHT UP
VERTICAL FLUE
Figure 7. Straight up Vertical Flue

V
11.8 m MAX.
STRAIGHT OUT HORIZONTAL FLUE
H H
MIN. RUN MAX. RUN
13.1” (33.2 cm) 24” (61.0 cm)
V
CAP
H

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 15
Figure 9. Flue with One 90° Elbow
Figure 10. Flue with One 90° Elbow
NOTE: For corner installations: A 15.2 cm MINIMUM
length of straight pipe must be rst attached to the
replace before 90o elbow. This will allow the ue pipe
to clear the top standoffs.
NOTE: If a 90º elbow is rst attached to the unit, the
maximum horizontal run is 3 feet (91.4 cm).
H
V
oELBOW
V H
MIN. 30.5 cm MAX. 61.0 cm
MIN. 61.0 cm MAX. 1.22 m
MIN. 91.4 cm MAX. 1.86 m
MIN. 1.22 m MAX. 2.48 m
MAX. 7.3 m MAX. 2.48 m
oELBOW
V H
MIN. 30.5 cm MAX. 1.22 m
MIN. 61.0 cm MAX. 2.4 m
MIN. 91.4 cm MAX. 3.7 m
MIN. 1.22 m MAX. 4.9 m
V + H = MAX 7.3 m H = MAX. 2.4 m
V
H

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/1316
Figure 11. Flue with Two 90° Elbows

V H H + H1
MIN. 30.5 cm MAX. 61.0 cm MAX. 1.22 m
MIN. 61.0 cm MAX. 61.0 cm MAX. 2.48 m
MIN. 91.4 cm MAX. 1.22 m MAX. 3.72 m
MIN. 1.22 m MAX. 1.8 m MAX. 4.9 m
MAX. 6.1 m MAX. 1.8 m MAX. 4.9 m
H
1
V
H

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 17
Figure 12. Flue with Two 90° Elbows

V H + H1
MIN. 30.5 cm MAX. 1.22 m
MIN. 61.0 cm MAX. 2.4 m
MIN. 91.4 cm MAX. 3.7 m
MIN. 1.22 m MAX. 4.9 m
V+H+H1= MAX. 11.8 m H+H1= MAX. 4.9 m
V+V1+H1= MAX. 12.97 m
H
1
H
V
V
V1
H

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/1318
Figure 13. Flue with three 90° elbows

MIN. 30.5 cm MAX. 61.0 cm MAX. 1.22 m
MIN. 61.0 cm MAX. 1.22 m MAX. 2.48 m
MIN. 91.4 cm MAX. 1.86 m MAX. 3.6 m
MIN. 1.22 m MAX. 2.48 m MAX. 4.9 m
H = MAX. 2.48 m MAX. 4.9 m
NOTE: V + V1+ H + H1= MAX. 10.97 m
V H H + H1
V H H + H1+ H2
MIN. 30.5 cm MAX. 61.0 cm MAX. 1.22 m
MIN. 61.0 cm MAX. 61.0 cm MAX. 2.48 m
MIN. 91.4 cm MAX. 1.22 m MAX. 3.6 m
MIN. 1.22 m MAX. 1.86 m MAX. 4.9 m
MAX. 6.1 m MAX. 1.86 m MAX. 4.9 m

V
H1
V1
H1
H2
V

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/13 19
V
H
H1
V
1
Figure 14. Flue with three 90° elbows
V H + H1
MIN. 30.5 cm MAX. 1.22 m
MIN. 61.0 cm MAX. 2.4 m
MIN. 91.4 cm MAX. 3.7 m
MIN. 1.22 m MAX. 4.9 m
V + V1 + H + H1 = MAX. 10.97 m
H + H1 = MAX. 4.9 m

V H + H1
MIN. 30.5 cm MAX. 1.22 m
MIN. 61.0 cm MAX. 2.4 m
MIN. 91.4 cm MAX. 3.7 m
MIN. 1.22 m MAX. 4.9 m
V + V1 + H + H1 = MAX. 10.97 m
H + H1 = MAX. 4.9 m

V
H
H1
V1

Heat & Glo • 6000TRS-CE • 2049-900 Rev. R • 3/1320
WARNING: THE REAR FLUE COLLAR SEAL
CAP MUST REMAIN ATTACHED TO THE REAR
FLUE COLLARS IF THE FLUE SYSTEM IS AT-
TACHED TO THE TOP STARTING COLLARS.
SEE FIGURE 15.
Figure 15
B. Installing Flue Components
After determining which set of starting collars will be used
(top or rear), follow venting instructions accordingly.
Venting Out the Rear Flue
Remove the installed rear seal cap from the rear starting
collars by cutting the strap at each end (See Figure 15).
Follow the ue conguration tables accordingly.
Remove the 12.7 cm diameter heat shield from the 1.27 cm
diameter collar by sliding it out. Remove insulation piece.
WARNING: FAILURE TO REMOVE INSULA-
TION IN THE SET OF COLLARS YOU ARE
USING COULD CAUSE A FIRE.
WARNING: YOU MUST LEAVE THE INSULA-
TION IN PLACE IN THE SET OF COLLARS YOU
ARE NOT USING.
!
!
!
!
     

THE FLUE SYSTEM IS ATTACHED TO THE
REAR STARTING COLLARS. SEE FIGURE 15.
Venting Out the Top Flue
Remove the top ue collar seal cap by cutting the strap on
each end. Remove both pieces of insulation inside the top
two starting collars (see Figure 15).
Remove the 10.2 cm diameter heat shield from the 10.2
cm diameter collar by sliding it out.
You have to take the glass off again for positioning the
logs when the unit is nally installed in place and nished
around it. Reinstall the glass door. Attach ue system to
the top starting collars.
Insert screwdriver
or similar object
here to remove cap.
CUT HERE
Venting
Out Rear
Venting
Out Top
HEAT
SHIELD
DISCARD
INSULATION
SEAL
CAP
SEAL
CAP
HEAT
SHIELD
INSULATION,
DISCARD
BOTH
PIECES