Heat & Glo STELLAR 3-SS-20-G User manual

Custom Fireplace Program
Co-linear Direct Vent
Powervented Gas Fireplaces
ENLIGHT COLLECTION
SINGLE-SIDED
Installation and Operating Manual
NG & Propane
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
— Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS
• Donottrytolightanyappliance.
• Donottouchanyelectricalswitch;donotuseanyphoneinyourbuilding.
• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthegassupplier’sinstructions.
• Ifyoucannotreachyourgassupplier,calltheredepartment.
— Installationandservicemustbeperformedbyaqualiedinstaller,serviceagencyorthegassupplier.
WARNING:Iftheinformationintheseinstructionsarenotfollowedexactly,areorexplosionmayresult
causingpropertydamage,personalinjuryorlossoflife.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
stellar.heatnglo.com
StellarbyHeat&Glo,adivisionofHearth&HomeTechnologies®·22160CedarAvenueSuite200,Lakeville,MN55044·(952)224-4072
Page 1

Readthismanualbeforeinstallingoroperatingthisappliance.
Pleaseretainthisowner’smanualforfuturereference.
Congratulations on selecting a
Stellar by Heat & Glo gas replace.
You've selected a model within the Enlight Collection that is
crafted to elevate even the most unique spaces. Each of our
Enlight Collection's seven conrations sets the stage with
the most robust ames in its class, with commercial grade
components providing the utmost in safety and reliability.
As the owner of a new replace, you’ll want to read
and carefully follow all of the instructions contained in this
owner’s manual.
Pay special attention to all cautions and warnings.
DO NOT DISCARD.
This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
InstallaionTeam:atthetimeofinstall,pleaserecordthefollowingpertinentinformation
aboutthereplaceforthehomeownersreference:
Model Name:
Serial Number: Date Installed:
Dealer Purchased From:
Dealer City/State: Dealer Phone:
Notes:
If your model number has not been lled out above, please contact your dealer the replace purchased through directly for assistance
identifying your model number by the serial number.
stellar.heatnglo.com
Stellar by Heat&Glo, a division of Hearth & Home Technologies, Inc.
22160 Cedar Avenue S.
Lakeville, MN 55044
(P) 952-224-4072
(E) [email protected]
Page 2

Page 3
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
The rating plate is used for multiple designs and multiple collections, and custom replaces.
The generic nomenclature listed on the rating plate will not identically match the model of Enlight replace you have.
The rating plate must stay with the replace and is located below the burner in an area that will only be reachable while servicing.
UL RATING PLATE LOCATION & MODEL NUMBER IDENTIFICATION
X
ViewingWidthOfTheFireplace(Feet)
3-4-5-6-7-8 = Enlight Model
9-15 = Only Used For Custom Models
CongurationOfTheFireplace
SS = Single Sided
ST = See Through
BY = Bay
PR = Pier
LC = Left Corner
RC = Right Corner
4S = Four Sided (Island)
StyleOfBurner
G = Enlight Models Only,
Direct Vent (Ribbon)
R = Ribbon
L = Log Oak (Not Driftwood)
T = Torch
ViewingHeightOfFireplace(Inches)
20-24-30-36-48-60 = Enlight Models Only
OH = Open Hearth (All Heights)
GL = Glass, Direct Vent (All Heights)
MODEL NUMBER IDENTIFICATION
8-XX-YY-G

INS_CUST UL REV E
Page 4
TABLE OF CONTENTS
Section Description Page
8Venting Continued 22-29
N. Vertical Cap Location & Clearances 30
O. Vertical Cap Location & Clearances - RS12/14/16 31
P. Vertical Cap Location & Clearances - RSIF160/180 31
Q.1 Wall Termination Cap Installation Without Damper 32
Q.2 Wall Termination Cap Installation With Damper 32
R.1. Roof Termination Cap Installation With Damper 33
R.2 Roof Termination Cap Installation Without Damper 33
S.1 Chase Top Cap Installation Without Damper 34
S.2 Chase Top Cap Installation With Damper 34
T. Chimney Shroud Types & Specications 35
U. Outside Air-Intake 36
V. Changing Outside Air From The Side To The Bottom 37
W. Room Air For Combustion - Toe Kick Example 1 38
X. Room Air For Combustion - Toe Kick Example 2 39
9Optional Venting Accessories 38-39
A. Vertical Air-Intake Side Chute 38
B. Universal Exhaust & Intake Louver 8/10 & 12 39
10 Electrical-Includes Standard & Tethered Control Panel 42-53
A. Electrical Installation Overview 42
B.1 Electrical Schematic - Service 43
B.2 Electrical Schematic - Install 44
B.3 Junction Box & Capacitor 45
C.1 Terminals 1 & 2 - LED Lights 45
C.2 Terminals 3 & 4 - Main Flame (Smart Home) 46
C.3 Terminals 5 & 6 - Fireplace Power 47
C.4 Terminals 7 & 8 - Powervent Connection 47
C.5 Terminals 9 & 10 - Flue Damper Connection 48
C.6 Terminals 11 & 12 - Flue Damper Prove 48
D. Tethered Control Panel Installation Overview 49
E.1 Tethered Electric Wiring Schematic - Field 50
E.2 Tethered Electric Wiring Schematic - Troubleshooting 51
11 Finishing 52-53
A.1 Finishing Using 1/2" Clearance Stando󰀨s 52
A.2 Finishing Using 1/2" Clearance Stando󰀨s 53
12 Lighting & Shutdown 54-55
A. Lighting The Fireplace 54
B. If The Fireplace Does Not Light 55
13 Inlet Pressure Testing 56
14 Finalizing The Installation 58
A. Installing The Glass Media
B. Flame Appearance
Section Description Page
Introduction & Homeowners Reference 3
Table Of Contents 4-5
1 Safety Information 6
A. Safety Icon Designations 6
B. Important Safety Considerations 6
2 Commonwealth of Massachusetts Requirements 7
3Specications 8-11
A. Fireplace Dimensions - All Sizes 8
B. Single Sided Dimentions Schematic 9
C. Fireplace Specications 10
D. Installation Overview 10
E. Placement Clearance Requirements 10
Non-Combustilble Materials Specications 10
Combustible Materials Specications 10
F. Fireplace Clearances To Combustibles 11
4Prepare The Fireplace 12-13
A. Stando󰀨 Installation 12
B. Nailing Tab Installation 12-13
5Important Framing Notes 14-17
A. Important Framing Notes & Framing Dimensions 14-15
B.1 Mantel Requirements - With 1/2" Stando󰀨s 16
B.1 Mantel Requirements - Without 1/2" Stando󰀨s 17
6Glass Frame Assembly 18-19
A. Glass Frame Assembly Identication 18
B. Install Glass Frame Assembly/Glass Edge Protectors 19
C. Remove Glass Frame Assembly 19
7 Gas Line Specications & Connection 20-21
A. Gas Line Connection 20
B. Gas & Electric Access Locations 21
8Venting 22-39
A. Approved Venting & Powervent Systems 22
B.1 System Supply Voltage Chart 22
B.2 Powervent Supply Voltage Chart 22
C. RS Series Powervent Specications 23
D. Chimney Collar Dimensions 23
E. RSIF Series Powervent Specications 24
F. In-line Powervent Preparations - RSIF 180 25
G. Horizontal Vent System Clearance 26
H. Wall Pass Through 26
I. Pitot Tube Information. 26
J. Vertical Terminations Guidelines 27
K. Horizontal Terminations Guidelines 27
L. Horizontal Cap Location & Clearances 28
M.1 Horizontal RS Powervent Placement Clearances 29
M.2 Horizontal RSIF Powervent Placement Clearances 29

Page 5
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
TABLE OF CONTENTS
Section Description Page
15 Maintenance 57
A. Vent System 57
B. Glass Cleaning & Replacement 57
16 Replacement Parts 58-60
A. Replacement Parts 58
B. Glass Size & Specications 59
C. Horizontal & Vertical Glass Trim Pieces 60
17 Service & Maintenance History - Basic Troubleshooting 61-63
Table For Documenting Service & Maintenance History 61
Basic Troubleshooting 62-63
LED Lights Remote Operating Instructions 64-70
Hearth & Home Technologies Warranty 71-72
= Contains New Or Updated Information

1 - SAFETY INFORMATION
• Installation and repair should be done only by a qualied
service person. The appliance should be inspected by a
qualied service person before use. Annual inspection by a
qualied service person is required to maintain warranty. When
drawing room air for combustion more frequent cleaning may
be required due to excessive lint from carpeting, bedding
materials, etc. It is imperative that control compartments,
burners and circulation air passageways of the appliance be
kept clean.
• Children and adults should be alerted to the hazards of high
surface temperatures and should stay away to avoid burns or
clothing ignition.
• Young children should be carefully supervised when they are
in the same room as the appliance. Toddlers, young children
and others may be susceptible to accidental contact burns. A
physical barrier is recommended if there are at risk individuals
in the house. To restrict access to a replace or stove, install
an adjustable safety gate to keep toddlers, young children and
other at risk individuals out of the room and away from hot
surfaces.
• Clothing or other ammable material should not be place on or
near the appliance.
• Adequate accessibility clearances for servicing and proper
operation must be maintained.
• This appliance must not share or be connected to a chimney
ue serving any other appliance.
• Keep area around the appliance clear of combustible materials,
gasoline and other ammable vapor and liquids.
• The ow of combustion and ventilation air must not be
obstructed.
DO NOT
RISK OF FIRE
IMPORTANT NOTE
STOP!
HOT GLASS WARNING
A. SAFETY ICON DESIGNATIONS
B. IMPORTANT SAFETY CONSIDERATIONS
• Due to high temperatures the appliance should be located out
of tra󰀩c and away from furniture and draperies.
• The glass front or any part removed for servicing the appliance
must be replaced prior to operating the appliance. Work should
be done by a qualied service technician.
• Clean glass only when cool and only with non-abrasive
cleansers.
• Do not operate this appliance with the glass/frame assembly
removed, cracked or broken. Replacement of the glass
assembly must only be performed by a licensed or qualied
service person. DO NOT SUBSTITUTE MATERIALS.
• Do not strike or slam glass assembly.
• Keep burner and control compartment clean.
• Do not use this replace if any part has been under water.
Immediately call a qualied service technician to inspect this
appliance and to replace any part of the control system and any
gas control which has been under water.
• DANGER: Under no circumstances should any solid fuel
(wood, coal, paper or cardboard etc.) be used in this appliance.
• STATE OF CA WARNING: This product and the fuels used
to operate this product (liquid propane or natural gas), and
the combustion of such fuels, can expose you to chemicals
including benzene, which is known to the State of California to
cause cancer and reproductive harm.
For more information go to: www.P65Warnings.ca.gov.
Various safety icons appear throughout this installation manual. Please familiarize yourself with the icons making sure you understand the serious
consequences that may occur if ignored or of handling the products inappropriately.
This indicates additional instructions that you should consider
during the installation.
This indicates something that you must never do.
This designates a danger of risk of re or damage to property.
This indicates danger of serious bodily injury or property
damage if glass is handled while still hot.
CAUTION
This indicates danger of serious bodily injury or property
damage
This indicates notes that may include reviewing warnings on
other pages throughout the manual
ThisreplacecomplieswithANSIZ21.50-2019/CSA2.22-2019VentedGasFireplacesandCAN/CSAP.4.1-15.
Installationmustconformwithlocalbuildingcodesorintheabsenceoflocalbuildingcodes,
withtheNationalFuelGasCode,ANSIZ223.1/NFPA54-CurrentEdition,ortheNaturalorPropaneInstallationCode,CSAB149.1
Page 6

Page 7
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
2 - COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS
For all sidewall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purpos-
es, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than (7) feet above nished grade
in the area of the venting, including but not limited to decks and porches, the following requirements shall be satised:
INSTALLATION OF CARBON MONOXIDE DETECTORS
At time of installation of side wall horizontally vented gas fueled
equipment, the installing plumber or gas-tter shall observe that a hard
wired carbon monoxide detector with an alarm and battery back-up is
installed on the oor level where the gas equipment is to be installed.
In addition, the installing plumber or gas-tter shall observe that a
battery operated or hard wired carbon monoxide detector is installed
on each additional level of the dwelling, building or structure served by
the side wall horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services of qualied
licensed professionals for the installation of hard wired carbon monoxide
detectors.
In the event that the side wall horizontally vented gas fueled equipment
is installed in a crawl space or attic, the hard wired carbon monoxide
detector with alarm and battery back-up may be installed on the next
adjacent oor level.
In the event that the requirements of this subdivision can not be met
at the time of completion of installation, the owner shall have a period
of thirty (30) days to comply with the above requirements; provided,
however, that during said thirty (30) day period, a battery operated
carbon monoxide detector with an alarm shall be installed.
APPROVED CARBON MONOXIDE DETECTORS
Each carbon monoxide detector as required in accordance with the
above provisions shall comply with NFPA 720 and be ANSI/UL 2034
listed and IAS certied.
SIGNAGE
A metal or plastic identication plate shall be permanently mounted to
the exterior of the building at a minimum of eight (8) feet above grade
directly in line with the exhaust vent terminal for the horizontally vented
gas fueled heating appliance or equipment. The sign shall read, in print
no less the one-half inch (1/2) in size, “GAS VENT DIRECTLY BELOW.
KEEP CLEAR OF ALL OBSTRUCTIONS”.
INSPECTION
The state or local gas inspector of the side wall horizontally vented
gas fueled equipment shall not approve the installation unless, upon
inspection, the inspector observes carbon monoxide detectors and
signage installed in accordance with the provisions of 248 CMR 5.08
(2) (a) 1 through 4.
EXEMPTIONS
The following equipment is exempt from 248 CMR 5.08 (2) (a) 1 through
4:The equipment listed in Chapter 10 entitled “Equipment Not Required
To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and Product Approved side wall horizontally vented gas fueled
equipment installed in a room or structure separate from the dwelling,
building or structure used in whole or in part for residential purposes.
MANUFACTURES REQUIREMENTS
GAS EQUIPMENT VENTING SYSTEM PROVIDED
When the manufacturer of Product Approved side wall horizontally
vented gas equipment provides a venting system design or venting
system components with the equipment, the instructions provided by the
manufacturer for installation of the equipment and the venting system
shall include:
Detailed instructions for the installation of the venting system design or
the venting system components; and a complete parts list for the venting
system design or venting system.
MANUFACTURES REQUIREMENTS
GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED
When the manufacturer of ProductApproved side wall horizontally vented
gas equipment does not provide the parts for venting the ue gases, but
identies “special venting systems”, the following requirements shall be
satised by the manufacturer:
The referenced “special venting systems” instructions shall be included
with the appliance or equipment installation instructions and; the
“special venting systems” shall be Product Approved by the Board, and
the instructions for that system shall include a parts list and detailed
Installation instructions.
A copy of all installation instructions for all Product Approved side wall
horizontally vented gas fueled equipment, all venting instructions, all
parts lists for venting instructions, and/or all venting design instructions
shall remain with the appliance or equipment at the completion of the
installation.
NOTE: THE FOLLOWING REQUIREMENTS REFERENCE VARIOUS MASSACHUSETTS AND NATIONAL CODES NOT CONTAINED IN THIS MANUAL.

INS_CUST UL REV E
Page 8
Model # B-VENT
FLUE
AIR
INTAKE
Finishing
Width
Finishing
Height
Height To
Top Trim
Overall
Height Center Of Vent Overall Width WEIGHT
Ø Ø A B C D E F LBS/KG*
The dimensions in green are the allowable nishing width and height required to t the glass into the replace; must not overlap onto glass.
3-SS-20-G 8" 10" 38-3/16 [970] 20 [508} 38 [1,067] 46 [1,168] 20-7/8 [530] 41-3/4 [1,065] 362 [164]
4-SS-20-G 8" 10" 50-3/16 [1,275] 20 [508} 38 [1,067] 46 [1,168] 26-7/8 [683] 53-3/4 [1,365] 441 [200]
5-SS-20-G 8" 10" 62-3/16 [1,580] 20 [508} 38 [1,067] 46 [1,168] 32-7/8 [835] 65-3/4 1,670] 521 [236]
6-SS-20-G 10" 10" 74-3/16 [1,884] 20 [508} 38 [1,067] 46 [1,168] 38-7/8 [987] 77-3/4 [1,975] 603 [274]
7-SS-20-G 10" 10" 86-3/16 [2,189] 20 [508} 38 [1,067] 46 [1,168] 44-7/8 [1,140] 89-3/4 [2,280] 683 [310]
8-SS-20-G 10" 12" 98-3/16 [2,494] 20 [508} 40 [1,016] 52 [1,321] 50-7/8 [1,292] 101-3/4 [2,584] 801 [363]
3-SS-24-G 8" 10" 38-3/16 [970] 24 [610] 42 [1,067] 50 [1,270] 20-7/8 [530] 41-3/4 [1,065] 382 [174]
4-SS-24-G 8” 10” 50-3/16 [1,275] 24 [610] 42 [1,067] 50 [1,270] 26-7/8 [683] 53-3/4 [1,365] 462 [210]
5-SS-24-G 8” 10” 62-3/16 [1,580] 24 [610] 42 [1,067] 50 [1,270] 32-7/8 [835] 65-3/4 [1,670] 546 [248]
6-SS-24-G 10” 10” 74-3/16 [1,884] 24 [610] 42 [1,067] 50 [1,270] 38-7/8 [987] 77-3/4 [1,975] 631 [286]
7-SS-24-G 10” 10” 86-3/16 [2,189] 24 [610] 42 [1,067] 50 [1,270] 44-7/8 [1,140] 89-3/4 [2,280] 715 [324]
8-SS-24-G 10" 12" 98-3/16 [2,494] 24 [610] 44 [1,118] 56 [1,422] 50-7/8 [1,292] 101-3/4 [2,584] 843 [382]
3-SS-30-G 8" 10" 38-3/16 [970] 30 [762] 48 [1,219] 56 [1,422] 20-7/8 [530] 41-3/4 [1,065] 445 [202]
4-SS-30-G 8" 10" 50-3/16 [1,275] 30 [762] 48 [1,219] 56 [1,422] 26-7/8 [683] 53-3/4 [1,365] 503 [228]
5-SS-30-G 8" 10" 62-3/16" [1,580] 30 [762] 48 [1,219] 56 [1,422] 32-7/8 [835] 65-3/4 [1,670] 594 [269]
6-SS-30-G 10" 10" 74-3/16 [1,884] 30 [762] 48 [1,219] 56 [1,422] 38-7/8 [987] 77-3/4 [1,975] 686 [311]
7-SS-30-G 10" 10" 86-3/16 [2,189] 30 [762] 48 [1,219] 56 [1,422] 44-7/8 [1,140] 89-3/4 [2,280] 776 [352]
8-SS-30-G 10" 12" 98-3/16 [2,494] 30 [762] 50 [1,270] 62 [1,574] 50-7/8 [1,292] 101-3/4 [2,584] 904 [410]
3-SS-36-G 8" 10" 38-3/16 [970] 36 [914] 54 [1,372] 62 [1,575] 20-7/8 [530] 41-3/4 [1,065] 445 [202]
4-SS-36-G 8" 10" 50-3/16 [1,275] 36 [914] 54 [1,372] 62 [1,575] 26-7/8 [683] 53-3/4 [1,365] 537 [244]
5-SS-36-G 8" 10" 62-3/16 [1,580] 36 [914] 54 [1,372] 62 [1,575] 32-7/8 [835] 65-3/4 [1,670] 633 [287]
6-SS-36-G 10" 10" 74-3/16 [1,884] 36 [914] 54 [1,372] 62 [1,575] 38-7/8 [987] 77-3/4 [1,975] 730 [331]
7-SS-36-G 10" 10" 86-3/16 [2,189] 36 [914] 54 [1,372] 62 [1,575] 44-7/8 [1,140] 89-3/4 [2,280] 826 [375]
8-SS-36-G 10" 12" 98-3/16 [2,494] 36 [914] 56 [1,422] 68 [1,727] 50-7/8 [1,292] 101-3/4 [2,584] 965 [438]
3-SS-48-G 8" 10" 38-3/16 [970] 48 [1,219] 66 [1,676] 74 [1,880] 20-7/8 [530] 41-3/4 [1,065] 506 [230]
4-SS-48-G 8" 10" 50-3/16 [1,275] 48 [1,219] 66 [1,676] 74 [1,880] 26-7/8 [683] 53-3/4 [1,365] 615 [279]
5-SS-48-G 8" 10" 62-3/16 [1,580] 48 [1,219] 66 [1,676] 74 [1,880] 32-7/8 [835] 65-3/4 [1,670] 724 [328]
6-SS-48-G 10" 10" 74-3/16 [1,884] 48 [1,219] 66 [1,676] 74 [1,880] 38-7/8 [987] 77-3/4 [1,975] 833 [378]
7-SS-48-G 10" 10" 86-3/16 [2,189] 48 [1,219] 66 [1,676] 74 [1,880] 44-7/8 [1,140] 89-3/4 [2,280] 942 [427]
8-SS-48-G 10" 12" 98-3/16 [2,494] 48 [1,219] 68 [1,727] 80 [2,032] 50-7/8 [1,292] 101-3/4 [2,584] 1,088 [494]
3-SS-60-G 8" 10" 38-3/16 [970] 60 [1,524] 78 [1,981] 86 [2,184] 20-7/8 [530] 41-3/4 [1,065] 568 [258]
4-SS-60-G 8" 10" 50-3/16 [1,275] 60 [1,524] 78 [1,981] 86 [2,184] 26-7/8 [683] 53-3/4 [1,365] 689 [313]
5-SS-60-G 8" 10" 62-3/16 [1,580] 60 [1,524] 78 [1,981] 86 [2,184] 32-7/8 [835] 65-3/4 [1,670] 811 [368]
6-SS-60-G 10" 10" 74-3/16 [1,884] 60 [1,524] 78 [1,981] 86 [2,184] 38-7/8 [987] 77-3/4 [1,975] 932 [423]
7-SS-60-G 10" 10" 86-3/16 [2,189] 60 [1,524] 78 [1,981] 86 [2,184] 44-7/8 [1,140] 89-3/4 [2,280] 1,054 [478]
8-SS-60-G 10" 12" 98-3/16 [2,494] 60 [1,524] 80 [2,032) 92 [2,336] 50-7/8 [1,292] 101-3/4 [2,584] 1,211 [549]
KEY = inches [mm] for columns A-F
WEIGHT = LBS [KG] Unit weight includes the replace, the glass panels and the glass media.
3-SPECIFICATIONS

Page 9
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
1/2 [13]
5/8 [16]
12
[305]
D
C
RECESSED
INTAKE
COLLAR
3’- 6’ = 15 [381]
8’ = 17 [432]
24 [610]
3’- 6’ = 6-1/8 [156]
8’ = 7-1/8 [181]
ACCESS
PANEL
ACCESS
PANEL
FLUE
B-VENT
12
[305]
E
F
A
B
6 5/8 [169]
3 [76]
3 [76]
1 25/32
[45]
3-SPECIFICATIONS
A. SINGLE SIDED DIMENSIONS
TOP VIEW
FRONT VIEW
LEFT SIDE VIEW RIGHT SIDE VIEW
Figure3A
Model 4-SS-24-G Shown In Example.
The full shop drawing for each width
can be found under the RESOURCES tab
at the stellar.heatnglo.com website.
inches [mm]

INS_CUST UL REV E
Page 10
3-SPECIFICATIONS
WARNING:NON-COMBUSTIBLEZONE:USEONLYNON-COMBUSTIBLEMATERIALINTHISAREAFORENTIREWIDTHOF
FIREPLACE.DONOTUSEWOOD,SHEETROCK,ETC.,INTHISZONE.
NOTE: OTHER CLEARANCES APPLY. ALL CLEARANCES MUST BE MAINTAINED.
RefertoSection4(Framing),Section5(Non-combustibleZone)andSection10(Finishing)formoreinformation.
C. SPECIFICATIONS
Model # B-VENT OA REG PV IN-LINE PV BTU’S ORIFICE
NG
ORIFICE
Propane
3' 8" 10" RS12 RSIF160 40,000 (2X) #43 (2X) #55
4' 8” 10” RS12 RSIF160 60,000 (3X) #43 (3X) #55
5' 8” 10” RS12 RSIF160 80,000 (4X) #43 (4X) #55
6' 10” 10” RS14 RSIF180 100,000 (5X) #43 (5X) #55
7' 10” 10” RS14 RSIF180 120,000 (6X) #43 (6X) #55
8' 10" 12" RS14 RSIF180 140,000 (7X) #43 (7X) #55
D. INSTALLATION OVERVIEW
1. Frame should be built after the replace is installed or extra clearance must be planned for at the intake collar. Framing must allow for vent
installation.
2. If masonry (optional) will be used, prepare foundation for the masonry load. A lintel is required to support the added weight above the replace.
3. Install hearth if desired.
4. Insert replace into framing.
5. Double check clearances to combustibles.
6. Complete gas line installation.
7. Complete electrical hook-up.
8. Complete venting installation.
9. Install facing material, mantel or cabinetry.
10. Install glass media/natural stone, and any interior options including mirrors and/or driftwood log set.
11. Verify proper operation of replace and all components.
E. PLACEMENT CLEARANCE REQUIREMENTS
• This replace must be installed on a level surface capable of supporting the replace and venting.
• Fireplace must be placed directly on wood or non-combustible surface (not linoleum or carpet) extending entire depth and width of replace.
• This replace may be installed in a bedroom.
NOTE:Thequaliedinstallershouldfollowtheprocedurebestsuitedfortheinstallation.
Non-CombustibleMaterialsSpecications
Material which will not ignite and burn.
Such materials are those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136, Standard Test
Method for Behavior of Materials in a Vertical Tube
Furnace at 750 ºC shall be considered non-combustible materials.
CombustibleMaterialsSpecications
Materials made of or surfaced with wood, compressed paper, plant bers,
plastics, or other material that can ignite and burn, whether ame proofed or
not, or plastered shall be considered combustible materials.

Page 11
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
3-SPECIFICATIONS
F. FIREPLACE CLEARANCES TO COMBUSTIBLES INCHES MILLIMETERS
From unit left & right sides 1 [25]
To ooring under replace 0 0
Unit top to ceiling 6[152]
Unit side to adjacent sidewall 1[25]
CLEARANCES SHOWN ARE MINIMUM TO COMBUSTIBLES
NON-COMBUSTIBLE FRAMING AND FINISHING MATERIALS ALLOWED RIGHT UP TO THE FIREPLACE.
6 [152]
This does not
include finishing
materials or
perpendicular wall
intended to cover
the face/trim.
Can be a recess and/or combustible perpendicular wall extending
past the face of the fireplace. Applies to both sides of glass.
Refer to Section 3 (Specifications - Single Sided Dimensions)
1 [25]
BVent Pipe
1
[25]
Air-intake collar can be rotated to vent off the side or from the bottom
of the fireplace. Refer to Section 9A (Venting Specifications)
Top
Standoffs
Top
Standoffs
1 [25] Required; 24” [610] Recommended for ease of
glass installation and future service access.
1
[25]
1 [25]
1
[25]
1/2 [13] Hood Standoffs
1
[25]
Top Black Trim
Bottom Black Trim
6 [152] Top Standoffs; shipped flat.
Quantity will vary by model & size.
Refer to Section 3 (Prepare The Fireplace)
for more information.
1/2
[13]
1
[25]
1/2 [13] Hood Standoffs.
Qty May Vary By Model & Size
Refer to Section 5 (Non-Combustible Zone)
for more information.
inches [mm]
Figure3F
Combustible nishing materials may cover the 3 [76] top and bottom black trim. Do not overlap glass.
Combustible framing allowed right up to the replace below the viewing area only.
A combustible mantel may be placed at the top of the viewing area. Do not overlap glass.
A combustible hearth extension may be used below the viewing area. Do not overlap glass.
Do not place on carpet, vinyl or soft surfaces.

INS_CUST UL REV E
Page 12
4-PREPARETHEFIREPLACE
CAUTION: FIREPLACE IS NOT LOAD-BEARING.
NOTE: OTHER CLEARANCES APPLY. ALL CLEARANCES MUST BE MAINTAINED.
A. STANDOFF INSTALLATION
STEP1:RefertoFigure4A.1
The stando󰀨s will be shipped in a at state placed on the rebox top.
Locate the stando󰀨s and loosen the screws holding them in place.
Figure4A.2
Figure4A.3
Placement of the stando󰀨s and nailing tabs.
LOOSEN SCREW
AND FOLD
STANDOFF
STEP2:RefertoFigure4A.2
Fold the center of the stando󰀨 up and both ends out at the perforated
lines. Using Figure 4A.2 for reference, locate the second pre-installed
screw on the rebox top at each stando󰀨 location. Remove the screw,
pivot the folded stando󰀨 into location and re-install the screw to secure
the stando󰀨. Tighten up the screw that was loosened in Step 1.
PIVOT FOLDED STANDOFF
AND SECURE
STANDOFF
NAILING TAB
REMOVE
SECOND SCREW
LOOSENED SCREW
Figure4A.1
STANDOFF

Page 13
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
4-PREPARETHEFIREPLACE
B. NAILING TABS
STEP1:RefertoFigure4B.1
The nailing tabs will be shipped in a at state
placed on the rebox sides.
Locate the nailing tabs and remove the
screws holding them in place.
STEP2:RefertoFigure4B.2
Bend the two (2) small tabs out on each
nailing tabs at the perforated lines.
Using Figure 4A.3 for reference, locate the
pre-drilled holes on the rebox side each
nailing tabs will be placed at.
STEP3:RefertoFigure4B.3&Figure4B.4
Set each nailing tab in place and secure
using two (2) screws each. Bend the
nailing tabs out from replace at the
remaining perforated line.
The nailing tabs will ensure the
1 [25] minimum clearance is kept to
combustible framing.
Refer to Figure 4B.5
Depending on your installation and how you
frame it out, you may not use the provided
nailing tabs.
Figure4B.2Figure4B.1
Figure4B.4Figure4B.4 Figure4B.5
1 [25]
Figure4B.3

INS_CUST UL REV E
Page 14
5-FRAMING&MANTELREQUIREMENTS
IMPORTANT FRAMING NOTES: inches [mm]
FRAMING SHOULD BE BUILT AFTER THE FIREPLACE IS INSTALLED OR EXTRA CLEARANCE MUST BE PLANNED FOR AT THE INTAKE
COLLAR AND FOR THE THICKNESS OF MATERIALS USED.
THE FIREPLACE IS NOT LOAD-BEARING
FRAMINGDIMENSIONSASSUMING1/2[13]DRYWALLORNON-COMBUSTIBLEBOARDUSED.
THESE DIMENSIONS REPRESENT THE FRAMING DIMENSIONS FOR COMBUSTIBLE MATERIAL.
NON-COMBUSTIBLE FRAMING AND FINISHING MATERIALS MAY BE USED WITHIN THESE DIMENSIONS RIGHT UP TO THE UNIT.
NOCOMBUSTIBLEMATERIALWITHIN6[152]OFTHETOPOFTHEFIREPLACE.
NOCOMBUSTIBLEMATERIALWITHIN1[25]OFTHESIDES,BACKANDFRONTOFTHEFIREPLACE.
COMBUSTIBLEMATERIALSHALLNOTBEPLACEDDIRECTLYONTHEFACEOFTHEFIREPLACE,TOPANDSIDES.
SEE SECTION 5 (NON-COMBUSTIBLE ZONE) AND SECTION 10 (FINISHING) FORDETAILSREGARDING1/2[25]STANDOFFS.
STEEL SURFACE MAY BE COVERED WITH NON-COMBUSTIBLE FINISHING MATERIAL.
1[25]CLEARANCETOTHEB-VENTMUSTBEMAINTAINED.
NOTE:Framingdimensionsshouldallowforwallcoveringthicknessandreplacefacingmaterials.
Whenusingahearth,adjustroughopeningsizeasnecessarytomaintainatleastminimumclearancerequirements.
If masonry is to be used (optional), prepare the necessary foundation for the masonry load. When masonry construction is being used, a lintel must be
used over top of replace to support the added weight. Build hearth to desired size and height. If a hearth extension is desired, combustible
material may be used.
CAUTION:Installreplaceonmetal,concreteorhardwoodsurfaceextendingthefullwidthanddepthofreplace.
CAUTION:VentcaplocationmustbeincompliancewithguidelinesinSection 8 (Venting) of this manual.
NOTE: DO NOT PIERCEANYOFTHEBLACKPAINTEDSURFACESWITHSCREWS,RIVETS,ETC.
THISINCLUDESTHE3"[76mm]BLACKTOPANDBOTTOMGLASSTRIMANDANYPAINTEDSIDESADJACENTTOTHE
GLASS.
NOTE: REFER TO DIMENSIONS SECTION FOR
ALLOWABLE FINISHING DIMENSIONS REQUIRED TO FIT THE GLASS PANELS INTO THE FIREPLACE.
FINISHING MATERIALS MUST NOT OVERLAP THE DIMENSIONS HIGHLIGHTED IN GREEN IN SECTION 2 (DIMENSIONS).
NEVER COVER THE GLASS WITH FINISHING MATERIALS.
ReviewtheIMPORTANTFRAMINGNOTESfullypriortoframing.

Page 15
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
5-FRAMING&MANTELREQUIREMENTS
MODEL A
Width
B
Height
C
Depth
3-SS-20-G 43-3/4 [1,111] 52 [1,321] 25-1/32 [636]
4-SS-20-G 55-3/4 [1,416] 52 [1,321] 25-1/32 [636]
5-SS-20-G 67-3/4 [1,721] 52 [1,321] 25-1/32 [636]
6-SS-20-G 79-3/4 [2,026] 52 [1,321] 25-1/32 [636]
7-SS-20-G 91-3/4 [2,330] 52 [1,321] 25-1/32 [636]
8-SS-20-G 103-3/4 [2,635 58 [1,473] 25-1/32 [636]
3-SS-24-G 43-3/4 [1,111] 56 [1,422] 25-1/32 [636]
4-SS-24-G 55-3/4 [1,416] 56 [1,422] 25-1/32 [636]
5-SS-24-G 67-3/4 [1,721] 56 [1,422] 25-1/32 [636]
6-SS-24-G 79-3/4 [2,026] 56 [1,422] 25-1/32 [636]
7-SS-24-G 91-3/4 [2,330] 56 [1,422] 25-1/32 [636]
8-SS-24-G 103-3/4 [2,635 62 [1,574] 25-1/32 [636]
3-SS-30-G 43-3/4 [1,111] 62 [1,574] 25-1/32 [636]
4-SS-30-G 55-3/4 [1,416] 62 [1,574] 25-1/32 [636]
5-SS-30-G 67-3/4 [1,721] 62 [1,574] 25-1/32 [636]
6-SS-30-G 79-3/4 [2,026] 62 [1,574] 25-1/32 [636]
7-SS-30-G 91-3/4 [2,330] 62 [1,574] 25-1/32 [636]
8-SS-30-G 103-3/4 [2,635 68 [1,727] 25-1/32 [636]
MODEL A
Width
B
Height
C
Depth
3-SS-36-G 43-3/4 [1,111] 68 [1,727] 25-1/32 [636]
4-SS-36-G 55-3/4 [1,416] 68 [1,727] 25-1/32 [636]
5-SS-36-G 67-3/4 [1,721] 68 [1,727] 25-1/32 [636]
6-SS-36-G 79-3/4 [2,026] 68 [1,727] 25-1/32 [636]
7-SS-36-G 91-3/4 [2,330] 68 [1,727] 25-1/32 [636]
8-SS-36-G 103-3/4 [2,635 74 [1,880] 25-1/32 [636]
3-SS-48-G 43-3/4 [1,111] 80 [2,032) 25-1/32 [636]
4-SS-48-G 55-3/4 [1,416] 80 [2,032) 25-1/32 [636]
5-SS-48-G 67-3/4 [1,721] 80 [2,032) 25-1/32 [636]
6-SS-48-G 79-3/4 [2,026] 80 [2,032) 25-1/32 [636]
7-SS-48-G 91-3/4 [2,330] 80 [2,032) 25-1/32 [636]
8-SS-48-G 103-3/4 [2,635 86 [2,184] 25-1/32 [636]
3-SS-60-G 43-3/4 [1,111] 92 [2,336] 25-1/32 [636]
4-SS-60-G 55-3/4 [1,416] 92 [2,336] 25-1/32 [636]
5-SS-60-G 67-3/4 [1,721] 92 [2,336] 25-1/32 [636]
6-SS-60-G 79-3/4 [2,026] 92 [2,336] 25-1/32 [636]
7-SS-60-G 91-3/4 [2,330] 92 [2,336] 25-1/32 [636]
8-SS-60-G 103-3/4 [2,635 98 [2,489] 25-1/32 [636]
A
B
C
Dimensions assume the 1/2" [13] clearance standos in place.
Refer to Section 5 (Non-combustible Zone) for more information on
installationsnotusingtheclearancestando󰀨s.
NOTE: IT IS RECOMMENDED TO SET THE FIREPLACE IN TO PLACE PRIOR TO INSTALLING THE FRAMING.
Framing dimensions noted are minimum framing dimensions to combustible materials only, and it is the responsibility of the installer
for determining framing dimensions that allow for wall covering thickness and replace facing materials for each individual installation.
inches [mm]
Figure5A

INS_CUST UL REV E
Page 16
5-FRAMING&MANTELREQUIREMENTS
B.1NON-COMBUSTIBLEZONE-USINGTHEPROVIDED1/2"STANDOFFS
FINISHING HEIGHT
BOTTOM 3 [76] TRIM
COMBUSTIBLE MANTEL
COMBUSTIBLE HEARTH
COMBUSTIBLE FACING
MATERIAL
SINGLE SIDED EXAMPLE: RIGHT SIDE VIEW
APPLIES TO BOTH SIDES AND ENDS IF USING A MULTI-SIDED FIREPLACE
TOP TRIM
TOP OF FIREPLACE
TOP OF TRIM
1/2 [13] CLEARANCE TO COMBUSTIBLES ON SURFACE
The fireplace ships with standoffs in place to ensure a
1/2” [13] clearance to combustibles is maintained on the surface.
COMBUSTIBLE OR NON-COMBUSTIBLE
BACKING MATERIAL (I.E. SHEETROCK)
COMBUSTIBLE OR
NON-COMBUSTIBLE MATERIAL
1/2 [13]
STANDOFFS
3 [76]
6 [152 mm]
MINIMUM NON-COMBUSTIBLE ZONE
OPEN AIR SPACE
COMBUSTIBLE FRAMING
6 [152]
3’-7’
8
[203]
3’-7’
14
[356]
8’
18
[457]
6 [152]
8’
12
[305]
inches [mm]
Figure5B.1
NOTE: Refer to Section 11 - Finishing The Wall (A.1) for more information.
The replace has stando󰀨s installed on the front of the replace standard from the factory. They are located on the
upper left, center and right front of the replace and are to ensure that the 1/2 [13] required clearance to
combustibles on the surface of the replace is maintained.
If the stando󰀨s are removed, only non-combustible material can be installed against the surface of the replace such
as a non-combustible backer cement board. 1/2 [13] minimum thickness must be used in the space* between the top of
the 3 [76] trim to the combustible framing the full width of the replace. The space* includes a 7 [178] minimum above
the top of the replace that is recommended for ease of attachment. *= 15 [381] for 3'-7' units and 19 [483] for 8' units.
RefertoFigure5B.1belowforastandardinstallationusingtheprovided1/2[13]stando󰀨s.
RefertoFigure5B.2forrequirementswhennotusingtheprovided1/2[13]stando󰀨s.
WARNING! Risk of Fire
Comply with all the minimum clearances as specied.
Note About Mantel Depth:
There are no minimum or maximum
depth requirements for the mantel.
Notes About TV Placement:
A mantel is not required if you are
placing a TV above the opening.
No minimum clearance required for a TV
above the replace opening.
1/2[13]Stando󰀨
INCHES [MM]

Page 17
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
5-FRAMING&MANTELREQUIREMENTS
B.2NON-COMBUSTIBLEZONE-NOT USINGTHEPROVIDED1/2"STANDOFFS
FINISHING HEIGHT
BOTTOM 3 [76] TRIM
COMBUSTIBLE MANTEL
COMBUSTIBLE HEARTH
COMBUSTIBLE FACING
MATERIAL
7 [178] ABOVE TOP OF FIREPLACE
COMBUSTIBLE OR NON-COMBUSTIBLE
BACKING MATERIAL (I.E. SHEETROCK)
COMBUSTIBLE OR
NON-COMBUSTIBLE MATERIAL
SINGLE SIDED EXAMPLE: RIGHT SIDE VIEW
APPLIES TO BOTH SIDES AND ENDS IF USING A MULTI-SIDED FIREPLACE
1/2 [13] CLEARANCE TO COMBUSTIBLES ON SURFACE
The fireplace ships with standoffs in place to ensure a 1/2 [13]
clearance to combustibles is maintained on the surface.
If the standoffs are removed, only non-combustible material can be
installed against the surface. See text above.
*= 15 [381] for 3'-7' units and 19 [483] for 8' units.
6 [152]
MINIMUM NON-COMBUSTIBLE ZONE
OPEN AIR SPACE
TOP TRIM
TOP OF TRIM
3 [76]
*
COMBUSTIBLE FRAMING
6 [152]
3’-7’
14
[356]
8’
18
[457]
3’-7’
8
[203]
8’
12
[305]
inches [mm]
Figure5B.2
The replace has stando󰀨s installed on the front of the replace standard from the factory. They are located on the left,
center and right front hood of the replace and are to ensure that the 1/2[13] required clearance to combustibles on the
surface of the replace is maintained.
If the stando󰀨s are removed, only non-combustible material can be installed against the surface of the replace such
as a non-combustible backer cement board. 1/2 [13] minimum thickness must be used in the space* between the top of
the 3 [76] trim to the combustible framing the full width of the replace. The space* includes a 7 [178] minimum above
the top of the replace that is recommended for ease of attachment. *= 15 [381] for 3'-7' units and 19 [483] for 8' units.
RefertoFigure5B.2belowforrequirementswhennotusingtheprovided1/2[13]stando󰀨s.
RefertoFigure5B.1forastandardinstallationusingtheprovided1/2[13]stando󰀨s.
NOTE: Refer to Section 11 - Finishing The Wall (A.2) for more information.
WARNING! Risk of Fire
Comply with all the minimum clearances as specied.
Note About Mantel Depth:
There are no minimum or maximum
depth requirements for the mantel.
Notes About TV Placement:
A mantel is not required if you are
placing a TV above the opening.
No minimum clearance required for a TV
above the replace opening.
1/2[13]Stando󰀨
INCHES [MM]

INS_CUST UL REV E
Page 18
6 - GLASS FRAME ASSEMBLY
Upper Groove
Quality
Suction Cup
Lower Groove
A. GLASS FRAME ASSEMBLY IDENTIFICATION
Figure 6A
CAUTION:TOPREVENTGLASSFRAMEASSEMBLYFROMFALLINGFROMFIREPLACEANDBECOMINGDAMAGED,FOLLOW
THE INSTRUCTIONS EXACTLY WHEN REMOVING AND INSTALLING GLASS FRAME ASSEMBLY.
STOP:DONOTOPERATETHISFIREPLACEWITHTHEGLASSREMOVED,CRACKEDORBROKEN.
REPLACEMENT OF GLASS ASSEMBLY SHOULD BE DONE BY A LICENSED OR QUALIFIED SERVICE PERSON.
WARNING: DO NOT REMOVE GLASS ASSEMBLY WHEN HOT!!!!
NOTE: GLASS REMOVAL AND INSTALLATION MUST BE PERFORMED WITH TWO PEOPLE.
NOTE:Glassmustberemovedusingqualitysuctioncups.
DO NOT attempt to remove the glass without using proper suction cups.
LOWER FILLER STRIP SITS OVER GLASS CLIPS
LOWER FILLER STRIP SITS OVER GLASS CLIPS
GLASS CLIP
GLASS CLIP
GLASS
GLASS
Figure 6B.1
NOTE:INCASEOFCHIPPEDORBROKENGLASS,duetothesizeandsensitivityofshippingtheglassseparatelyitisbestto
havethereplacementglasscutlocallyifneeded.
REFER TO SECTION 16 - REPLACEMENT PARTSFORTHEGLASSSIZECHARTFORDIMENSIONSANDSPECIFICATIONS.

Page 19
INS_16400-7800 Rev B ENLIGHT SINGLE-SIDED
C. REMOVE GLASS FRAME ASSEMBLY
B. INSTALL GLASS FRAME ASSEMBLY
1. Apply the suction cups to the outer glass panel following the instructions included with the suction cups.
2. Gently lift the glass until the bottom edge is clear of the groove it sits in.
3. Bring the bottom edge of the glass towards you while lowering it to disengage it from the top groove.
4. Sit the glass on a padded surface to protect it. IMPORTANT: Protect the glass's edges.
5. Remove the lower trim piece that sits between the layer of glass.
6. Remove the inner trim vertical pieces.
7. Using the suction cups, remove the inner glass in the same manner.
RefertoSection6(GlassFrameAssemblyIdenticationFigures6A&6B.1)wheninstallingandremovingtheglassframeassembly.
6 - GLASS FRAME ASSEMBLY
IMPORTANT: PLASTIC GLASS EDGE PROTECTORS
The replace is shipped with a plastic edge protector on
the outer pane of glass only.
See Figure 6B.2
Inner Glass
1. Unwrap the panes of glass carefully making sure to protect the
edges.
2. Apply the suction cups to the inner glass assembly, following
instructions included with the suction cups.
3. Lift the glass into place. The top edge slips into the top groove
(the glass will be behind the glass clip and against the gasketing);
lift into the groove until the bottom is clear of the bottom trim.
Make sure the glass is behind all the glass clips and slide the glass
down into the inner bottom grove. Gently push the glass tightly into
the gasketing. See Figure 6A
4. Push vertical glass trim into place on each side.
Once into place, slide the vertical glass trim all the way down so the
top is almost even with the top viewing area. See Figure 6B.3
5. Place the long horizontal trim piece between the lower glass clips.
Slide back against the inner glass. See Figure 6B.3 and
Figure 6B.4.
Outer Glass
6. Apply the suction cups to the outer glass and lift it into place in the
same manner as the inner glass.
Figure6B.3-VerticalTrimPiece
Figure6B.4-HorizontalTrimPiece
Figure 6B.2 - Outer Glass Edge Protector
Top/BottomGlassPane
U-Shaped
Edge
Protector
WARNING: RISK OF INJURY!
DO NOT remove glass until unit is cooled to room
temperature.Glassbreakagecouldoccur.

INS_CUST UL REV E
Page 20
7-GASLINESPECIFICATIONS
A. GAS LINE CONNECTION Propane NG
MINIMUM INLET GAS PRESSURE 11.0 inches W.C.
(recommended)
7.0 inches W.C.
(recommended)
MAXIMUM INLET GAS PRESSURE 14.0 inches W.C. 10.0 inches W.C.
MANIFOLD PRESSURE (HI) 10.0 inches W.C. 3.5 inches W.C.
ORIFICE SIZE See Specications Chart
in Section 3.C
See Specications Chart
in Section 3.C
INPUT BTU/HR See Specications Chart
in Section 3.C
See Specications Chart
in Section 3.C
ThisreplaceismanufacturedforusewithNaturalGasorPropane.
CAUTION:Installationofthegaslinemustonlybedonebyaqualiedpersoninaccordancewithlocalbuildingcodes,ifany.
Ifnot,followANSI223.1.
NOTE:Theapplianceanditsindividualshuto󰀨valvemustbedisconnectedfromthegassupplypipingsystemduringany
pressuretestingofthatsystematpressuresinexcessof½psi.
NOTE:Theappliancemustbeisolatedfromthegassupplypipingsystembyclosingitsindividualmanualshut-o󰀨valveduring
anypressuretestingofthegaslineattestpressuresequaltoorlessthan½psi(3.5kPa).
NOTE:Forhighaltitudeinstallations,consultStellarbyHeat&Glodirectlyforproperratingmethods.
Figure7
1/2” Gas Supply
1/2in.GasSupply3'-7'
3/4in.GasSupply8'
ADDITIONAL INFORMATION
INSECTION2.B(GAS&ELECTRICACCESSLOCATIONS)
Gas Valve
Ball Valve
NOTE: Have the gas supply line installed in accordance with local codes. If not, follow ANSI Z223.1. Installation should be done by a qualied installer
approved and/or licensed as required by the locality. In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or
gas tter.
NOTE: A listed (and Commonwealth of Massachusetts approved) 1/2 in. or 3/4 in. T-handle manual shut-o󰀨 ball valve is connected to the
1/2 in. or 3/4 in. control valve inlet.