Heath Zenith DualBrite User manual

FEATURES
• Automatically comes on when motion is de-
tected.
• Automatically turns light o.
• Dusk Accent lighting.
• Photocell keeps the light o during daylight
hours.
is package includes:
• Coach Light
• Mounting Bracket and Screws
• Wire Connectors
• Owner’s Manual
REQUIREMENTS
• e light control requires 120 volts AC.
• If you want to use Manual Mode, the control
must be wired through a switch.
• Some electrical codes require installation by
a qualied electrician.Please check the codes
in your area.
Model 4167
Before installation, record the model num-
ber listed inside the xture. Attach receipt
in case of possible warranty issues.
Model Number:
© 2013 HeathCo LLC 200471-02A
Installation and
Operating Instructions
DualBrite®Motion
Sensing Coach Light
Coach Light

2200471-02
GND
WIRING
CAUTION: DO NOT connect the RED
wire unless you want to control other
lights from the motion sensor (see Op-
tional Wiring).
Note: All wiring must be run in accordance with
the National Electrical Code through conduit
or another acceptable means. Contact a quali-
ed electrician if there is any question as to the
suitability of the system.
WARNING: Turn power o at circuit
breaker or fuse.
One Motion Light
Two Motion Lights
Black
White
Green
or Bare
Light
Fixture
Black
White
Green
or Bare
Light
Fixture
Light
Fixture
Ground Screw
INSTALLATION
Bracket
Mounting
Screws
Junction
Box
Note:Werecommendhavinganassistanthelphold
the lantern assembly during the wiring process.
For best performance, mount the xture about 6
feet (1.8 m) above the ground.
1. Remove two decorative nuts.
2. Remove X-Bar.
3. Tighten mounting screws on X-Bar nger
tight.
4. Attach X-Bar to junction box.
WARNING: Turn power o at circuit
breaker or fuse.
X-Bar
Decorative Nut
Lantern Base
Lantern Mounting
Screw
X-Bar

3
200471-02
Black to black
White to white
Recommended Grounding Method
Use a green ground“pigtail”(not provided) and
twistoneendtogetherwiththebarexturewire
and the box ground wire. Secure with a wire
connector. Secure the other end of the “pigtail”
with the GND screw on the mounting plate.
Connect the xture wires to the wires in the junc-
tion box.Twist the wires together and secure with
wire connectors.
If you have metal junction box,you may not need
the green “pigtail”. If you are unsure about the
grounding method, consult your local building
code.

4200471-02
OPTIONAL WIRING
is xture is provided with a sensor rated for 360 Watts. Since the xture is only rated 100 Watts,
260 Watts of additional lighting may be controlled by this sensor.
When determining what a xture is rated for, do not simply look at the rating on the light bulb in
the xture. Look at the marking which species the maximum bulb wattage for which the xture
is suitable.
Once you have selected the xtures to be connected and determined their maximum ratings,add these
ratings up. For instance,if you have 3 xtures rated 100 Watts, 150 Watts, and 75 Watts respectively,
you have a total load of 325 Watts.
Wiring Diagram 1 – When wiring to control a standard light xture: Strip the motion sensor’s
red wire and connect to the standard light’s black wire.Connect all white wires together.Total xture
ratings must not exceed 360 Watts (3.0 A).
Wiring Diagram 2 – When wiring to control another motion sensing light xture (Master /
Slave): Strip the red wire in both light xtures. Connect the red wire of the controlling (master)
xture to the red and black wires of the controlled (slave) xture. Connect all white wires together.
Total xture ratings must not exceed 360 Watts (3.0 A).
Wiring Diagram 3 – When wiring so either motion light turns on the both motion lights
(Master / Master): Strip the red wire in both light xtures. Connect the red wire of one xture
to the red wire of the second xture. Note: In most installations, an additional wire (same gauge as
existing house wire) will have to be installed in the house to connect the two xtures as master /
master. Connect all white wires together and all black wires together. Total xture ratings must not
exceed 360 Watts (3.0 A).
Black
White
Green
or Bare
Light
Fixture
Light
Fixture
(Standard) Master Slave
Black
White
Green
or Bare
Light
Fixture
Light
Fixture
Red
Red
Wiring Diagram 1 Wiring Diagram 2
Wiring Diagram 3
Master Master
Black
White
Red
Green
or Bare
Light
Fixture
Light
Fixture

5
200471-02
Junction
Box
FINAL ASSEMBLY
1. Push the wires into the junction box. Make
sure none of the wires get pinched.
2. Slide the xture assembly onto the mounting
screws.Tighten decorative nuts removed in step
1 of Installation section securely against xture
base.
Mounting Screw
Decorative Nut
3. Install one medium base light bulb (100 Watt
maximum).
4. Caulkaroundxturebasewithsiliconeweather
sealant after all Testing and Adjustments are
complete.
TESTING AND ADJUSTMENTS
1. Turn on the circuit breaker and light
switch.
Note: Sensor has a 1 1/2minute warm up period
before it will detect motion.When rst turned
on wait 1 1/2minutes.
2. Set:
• ON-TIME switch to TEST
• DB® switch to OFF
• SENSITIVITY dial to Midway
3. Walk through the coverage area noting where
you are when the lights turn on.InTEST mode,
light will stay on for 5 seconds after sensing
motion and then turn o.
TEST 1 5 10
MINUTE
OFF 3 6 DUSK TO
HOUR DAWN
–+
SEN

6200471-02
Note:Whenrstturnedonwaitabout11/2minutes
for the circuitry to calibrate.
* resets to Auto Mode at dawn.
OPERATION
MANUAL MODE
4. Adjust the SENSITIVITY to increase or
decrease the range as needed.Too much sen-
sitivity may cause false triggering due to heat
sources in the coverage area (see Adjustment
of Coverage Area or Troubleshooting section).
5. Set the amount of ON-TIME you want the
light to stay on after motion is detected (1, 5,
or 10 minutes).
6. Set the DB® switch to o,3 hours,6
hours, or dusk-to-dawn.
Mode: On-Time Works: Day Night
Test 5 Seconds x x
Auto 1, 5, or 10
Minutes x
Accent 3, 6 Hour,
To Dawn x
Manual To Dawn* x
... back on.
1 Second
OFF then...
Manual mode only works at
night because daylight returns
the sensor to AUTO.
Flip the light switch o for one
second then back on to toggle
betweenAUTOandMANUAL
MODE.
Manual mode works only with
the ON-TIME switch in the 1,
5, or 10 position.
30 ft.
(9.1 m)
6 ft.
(1.8 m)
180°
Maximum
Maximum Range Coverage Angle*
(Top View)
Least Sensitive Most Sensitive
e sensor is less sensitive to motion directly
towards it and more sensitive to motion across
coverage area.
Sensor
Motion Motion

7
200471-02
ADJUSTMENT OF COVERAGE AREA
e sensor on this light xture detects “motion”
by the movement of heat across the coverage
area. However, following are examples of objects
that also produce heat and can cause the sensor
to trigger:
• Pools of Water • Air Conditioners
• Dryer Vents • Animals
• Heating Vents • Automobile Trac
If you suspect that a heat source of this type is
triggering the sensor, reduce the sensitivity.
SPECIFICATIONS
Range .................................................Up to 30 ft. (9.1 m) [varies with surrounding temperature]
Sensing Angle.....................................Up to 180°
Electrical Load ...................................Up to 100 Watt Maximum Incandescent
Bulb Type ...........................................Medium Base,Type “A”, 100 Watt Maximum
Sensor Capacity..................................Up to 360 Watt (3.0 A) Maximum Tungsten
Power Requirements...........................120 VAC, 60 Hz
Operating Modes ...............................TEST, AUTO, and MANUAL MODE
ON-Timer..........................................1, 5, 10 minutes
DB® Timer...........................O, 3, 6 hours, dusk-to dawn
Test Timer..........................................5 Seconds
Manual Mode Timer..........................Dusk-to-Dawn
MANUAL MODE
AUTO
TEST
ON-TIME Switch at 1, 5,
or 10 minutes
MODE SWITCHING SUMMARY
Flip light switch
o for one second
then back on*
* If you get confused while switching modes, turn
the power o for one minute, then back on. After
thecalibrationtimethecontrolwillbeintheAUTO
mode.
DualBrite®Dimmer Control
Light comes on half bright for selected time after
dusk (O,3 hr.,6 hr.,until dawn).Selecting OFF
disables this feature.e motion sensing features
will continue to work as described in this manual.
If motion is sensed, the light turns on full bright
for the ON-TIME (1, 5, or 10 minutes) then
returns to dim mode.

8200471-02
SYMPTOM POSSIBLE CAUSE SOLUTION
Lights will not
come on. 1. Light switch is turned o. 2. Light bulb is loose or burned out.
3. Fuse is blown or circuit breaker is turned o.
4. Daylight turn-o is in eect.
5. Sensor not detecting movement.
6. Incorrect circuit wiring, if this is a new installation.
1. Turn light switch on.
2. Check bulb and replace if burned out.
3. Replace fuse or turn circuit breaker on.
4. Recheck after dark.
5. Re-aim the sensor to cover desired area.
6. Verify wiring is correct.
Lights come on in
daylight. 1. Light control may be installed in a relatively dark location.
2. Light control is in TEST.
1. e xture is operating normally under these
conditions.
2. Set control switch to 1, 5, or 10 minutes.
Lights come on for
no apparent reason. 1. Lightcontrolmaybesensingsmallanimalsorautomobile trac.
2. Sensitivity is set too high.
1. Re-aim sensor. Reduce sensitivity.
2. Reduce sensitivity.
Lights stay on
continuously. 1. e sensor may be picking up a heat source like an air vent, dryer vent, or brightly painted, heat-reective
surface.
2. Light control is in Manual Mode.
3. Light control is in DB® mode.
4. Sensitivity is set too high.
1. Re-aim sensor. Reduce sensitivity.
2. Switch to Auto.
3. Slide DB® switch to OFF position.
4. Reduce sensitivity.
Lights ash on
and o. 1. Light control is in the TEST mode and warming up. 2. Heatbeingreectedfromotherobjectsmaybe aecting
the sensor.
1. Flashing is normal under these conditions.
2. Re-aim sensor. Reduce sensitivity.
TROUBLESHOOTING GUIDE
TECHNICAL SERVICE
Please call 1-800-858-8501 (English speaking only) for assistance before
returning product to store.
If you experience a problem, follow this guide. You may also want to visit our Web site at: www.
hzsupport.com. If the problem persists, call* for assistance at 1-800-858-8501 (English speaking
only), 8:00 AM to 5:00 PM CST (M-F). You may also write* to:
HeathCo LLC
P.O. Box 90045
Bowling Green, KY 42102-9045
ATTN: Technical Service
* If contacting Technical Service, please have the following information available: Model Number,
Date of Purchase, and Place of Purchase.
No Service Parts Available for this Product
Please keep your dated sales receipt, it is required for all warranty requests.

9
200471-02
TWO YEAR LIMITED WARRANTY
is is a “Limited Warranty”which gives you specic legal rights.You may also have other rights
which vary from state to state or province to province.
For a period of two years from the date of purchase,any malfunction caused by factory defective
parts or workmanship will be corrected at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence,
light bulbs,batteries,and other expendable items are not covered by this warranty.Unauthorized
service or modication of the product or of any furnished component will void this warranty in
its entirety.is warranty does not include reimbursement for inconvenience,installation, setup
time, loss of use, unauthorized service, or return shipping charges.
is warranty covers only HeathCo LLC assembled products and is not extended to other equip-
ment and components that a customer uses in conjunction with our products.
THISWARRANTYISEXPRESSLYINLIEUOFALLOTHERWARRANTIES,EXPRESS
OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDI-
TION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY
PARTICULARPURPOSE OR USE,ANDSPECIFICALLY INLIEU OF ALLSPECIAL,
INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHECUSTOMER
AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO LLC FOR
ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS,
WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclu-
sion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
Please keep your dated sales receipt, it is required for all warranty requests.
HeathCo LLC reserves the right to discontinue products and to change specications at any time
without incurring any obligation to incorporate new features in products previously sold.

10 200471-02 © 2013 HeathCo LLC 200471-02 S
CARACTERÍSTICAS
• Se enciende automáticamente al detectar mo-
vimiento.
• Apaga la luz automáticamente.
• Iluminación ornamental de baja intensidad.
• La fotocélula mantiene la luz apagada durante
las horas diurnas.
Este paquete contiene:
• Luz de Coche
• Ménsula y tornillos para montaje
• Conectores de alambre
• Manual del propietario
REQUISITOS
• El control de luz requiere 120 VCA.
• Para usar el Modo Manual, conecte el control
con un interruptor.
• Algunoscódigosrequiereninstalaciónporun
electricistacalicado.Reviseloscódigosensu
área.
Modelo 4167
INSTRUCCIONES PARA SU
INSTALACIÓN Y FUNCIONAMIENTO
Antesdeinstalar,registreelnúmerodelmode-
lomostradodentrodelaparato.Fije elrecibo
en caso posibles reclamos por la garantía.
Número del modelo:
DualBrite®Luces de
Coches Detectores de
Movimiento
Luz de Coche