Heath Zenith 7307 User manual

© 2018 HeathCo LLC 209669-02A
1. Remove orange battery tab from push
button. Remove back of case by pushing in
tab on bottom with a small screwdriver (see
Figure 1). Remove orange battery tab.
2. Plug in wireless chime (see Figure 2).
IMPORTANT: This power unit is intended to
be correctly orientated in its vertical mount
position.
This plug will fit into the power outlet only as
recommended by the manufacturer. Do not
try reversing the plug.This is a safety feature.
If you are unable to insert the plug fully into
the outlet, contact your electrician to replace
your obsolete outlet.
3. Test range. Temporarily position push button
where you want it mounted.Press push button
to verify chime and push button work properly.
If chime does not sound, see Troubleshooting.
Figure 1
WARNING: To prevent possible
SERIOUS INJURY or DEATH:
• NEVER allow small children near
batteries.
• If battery is swallowed, immediately
notify doctor.
This package includes (Style of push button and chime may vary from illustration):
Model
Wireless
plug-in
chime
Wireless push
button
Hardware
pack
7307 ✔ ✔ ✔
Figure 2
Wireless Plug-In
Chime

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
2
4. Mount push button. Use either screws or
double sided tape to mount push button.
• Screw Mounting: To mount with screws,
remove back of case by pushing in tab
on bottom with a small screwdriver (see
Figure 1). Note: Remove material in screw
holes (if needed) before mounting with
screws. Attach back of case to door jamb
or wall (see Figure 3). Snap front of push
button on.
• Tape Mounting: When attaching push but-
ton using double sided tape, make sure the
surface of the door jamb or wall is clean.
Figure 3

3
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
Tune Setting Table
Multifunction Button
Tune Settings
The chime has different selectable tunes: Ding (one note tune), Ding-Dong
(two note tune), Westminster, or Whittington. The factory setting is for the
Westminster tune. This tune can be changed by following the instructions in
the Tune Setting Table.
Note: All chime models are designed to work with up to 5 push buttons (sold
separately). All chimes are designed to play only two different tunes no matter
how many push buttons are used.
Push Button Chime Tune
Jumper - ON
(Back Door)
——— Ding
Jumper - OFF
(Front Door)
Press and release button on chime.
Listen for selected tune. Repeat to
select different tune.
Selected
Musical Tune
Inside Push Button
Jumper Off Jumper On
Tune Selection Guide
Front Door
Ding-Dong
Westminster
Whittington
Back Door
Ding
ON
1 2
CR2032
TYPE “C”
TYPE “C”
1 2 3 4 5 6 7 8
CR2032
ON
1 2
TYPE “C”
TYPE “C”
1 2 3 4 5 6 7 8
PRESS & HOLD TUNE - 1 SEC SYNC - 3 SEC RESET - 10 SEC

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
4
Troubleshooting
1. PROBLEM: Chime does not sound or rang one time and quit.
A. POSSIBLE CAUSE: Push button and chime are not synced.
A. CORRECTIVE ACTION: Sync the push button and chime.
• Press and hold the button on the chime until the chime sounds a
“Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a
“Beep-Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
B. POSSIBLE CAUSE: Push button battery is not installed correctly.
B. CORRECTIVE ACTION: Make sure battery is installed according to the
diagram inside the push button.
C. POSSIBLE CAUSE: Push button battery is dead.
C. CORRECTIVE ACTION: Check charge of push button battery and replace
if necessary.
D. POSSIBLE CAUSE: Chime is not receiving power.
D. CORRECTIVE ACTION: Make sure the plug-in chime has power.
2. PROBLEM: Push button battery seems okay, but the chime does not work
after installation.
A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near
metal studs. Note: Metal reduces transmission range.
A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims
to move push button away from metal surface. Move chime to a different
wall outlet.
B. POSSIBLE CAUSE: Chime is mounted near concrete floor or wall.Note:
Concrete may reduce range.
B. CORRECTIVE ACTION: Move chime away from concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate chime closer to push button.

5
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
3. PROBLEM: Chime sounds when not intended (false triggers).
POSSIBLE CAUSE: Chime is receiving interference from another wire-
less device.
CORRECTIVE ACTION: Reset chime and push button.
• Remove push button battery. Wait 30 seconds.
• Press and hold the push button for 10 to 15 seconds within 60 seconds
after installing battery into the push button.
• Press and hold the button on the chime until the chime sounds a
“Beep-Beep-Beep-Beep”.
• To re-sync the push button and chime, press and hold the button on
the chime until the chime sounds a “Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a
“Beep-Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
Note: The push button and chime come synced from the factory. The range of
the wireless chime can vary with location, temperature, and battery condition.
PRESS & HOLD
TUNE - 1 SEC
SYNC - 3 SEC
RESET - 10 SEC
PRESS & HOLD TUNE - 1 SEC SYNC - 3 SEC RESET - 10 SEC

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
6
Please contact us for assistance
before returning product to the
store or to HeathCo LLC.
If you experience a problem, follow
this guide.You may also contact us be-
tween 8:00 AM to 5:00 PM CST (M-F).
When contacting Technical Service,
please include the following informa-
tion: Name, Street Address, Daytime
Phone Number, Email Address, Model
Number, Date of Purchase, Place of
Purchase, Product Issue, and DATED
SALES RECEIPT FOR WARRANTY
REQUESTS.
Technical Service
No Service Parts Available for this
Product
HeathCo LLC
P.O. Box 90045
2445 Nashville Road
Bowling Green, KY 42101, USA
ATTN: Technical Service
Internet: www.hzsupport.com
Phone:[phone] (English Only)
Fax: [phone]

7
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
HeathCo LLC reserves the right to discontinue and to change specifications
at any time without notice without incurring any obligation to incorporate new
features in previously sold products.
ONE YEAR LIMITED WARRANTY
This is a “Limited Warranty” which gives you specific legal rights. You
may also have other rights which vary from state to state or province
to province.
For a period of one year from the date of purchase, any malfunction
caused by factory defective parts or workmanship will be corrected at
no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs, batteries, and other expendable items
are not covered by this warranty. Any damage to the light fixture resulting
from the use of chemicals or a pressure washer machine are not covered
by this warranty. Unauthorized service or modification of the product or
of any furnished component will void this warranty in its entirety. This
warranty does not include reimbursement for inconvenience, installation,
setup time, loss of use, unauthorized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not
extended to other equipment and components that a customer uses in
conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRAN-
TIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRE-
SENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE
PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND
SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE
CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART
OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITEDTO ANY
LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEE-
ABLE. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
Please keep your dated sales receipt, it is required for all warranty
requests.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501
8
© 2018 HeathCo LLC 209669-02 S
Campana
inalámbrica con luz
estroboscópica
1. Retire la pestaña naranja de la batería del
botón pulsador. Extraer la parte posterior de
la caja presionando la aleta en el botón con
un destornillador pequeño (vea la Figura 1).
Quite la aleta anaranjada de la batería.
2. Campana inalámbrica enchufable.
IMPORTANTE: Esta unidad de alimentación
está diseñada para orientarse correctamente
en su posición de montaje vertical.
Este enchufe se encajará en el tomacorriente
solo según lo recomendado por el fabricante.
No trate de invertir el enchufe. Esta es una
característica de seguridad. Si no puede
insertar el enchufe en el tomacorriente por
completo, comuníquese con su electricista
para reemplazar su tomacorriente obsoleto.
ADVERTENCIA: Para prevenir una
posible LESIÓN SERIA o LA MUERTE:
• NUNCA deje que los niños estén cerca
de las baterías.
• Si se traga una batería, notifique inme-
diatamente al doctor.
Figura 1
Figura 2
Este paquete tiene (El estilo del pulsador y de la campana puede variar de
la ilustración):
Modelo
Campana
inalámbrica
enchufable
Pulsador
inalámbrico
Paquete de
ferretería
7307 ✔ ✔ ✔

9
Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501
Figura 3
3. Pruebe el alcance. Ponga provisionalmente
el pulsador en la posición donde lo quiera
instalar. Presione el pulsador para verificar
que la campana y el pulsador funcionen
apropiadamente. Si la campana no suena,
vea Análisis de Averías.
4. Instale el pulsador. Use ya sean tornillos o
cinta adhesiva por ambas caras para instalar
el pulsador.
• Montaje con tornillos: Para montar con
tornillos, quite la parte de atrás de la caja
empujando hacia adentro la lengüeta de
abajo con un destornillador pequeño y
girando la cuchilla (vea la Figura 1). Nota:
Quite la suciedad de los orificios para
tornillos (si es necesario) antes de poner
los tornillos. Coloque la parte de atrás de
la caja contra la jamba o la pared (vea la
Figura 3). Encaje a presión la parte frontal
del pulsador.
• Montaje con cinta adhesiva: Cuando
fije el pulsador usando cinta adhesiva por
ambas caras, asegúrese que la superficie
de la pared o la del batiente de la puerta
estén limpias.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501
10
Programación del tono
La campanilla tiene diferentes melodías que se pueden seleccionar: Ding
(melodía de una nota), Ding-Dong (melodía de dos notas), Westminster, o Whit-
tington.La calibración de fábrica es el tono Westminster. Esta melodía se puede
cambiar siguiendo las instrucciones de la Tabla de Programación de Melodías.
Nota: Todos los modelos de campanillas están diseñados para trabajar hasta
con 5 botones pulsadores (se venden por separado). Todas las campanillas
están diseñadas para reproducir solo dos melodías diferentes, sin importar
cuántos botones pulsadores se utilicen.
Tabla de programación de melodías
Botón Multifunción
Botón
pulsador
Campanilla Ajustes
Puente:
ENCENDIDO
(Puerta posterior)
———
Ding
Puente:
APAGADO
(Puerta principal)
Presione y suelte el botón de la campa-
na. Escuche el tono seleccionado. Re-
pita para seleccionar un tono diferente.
Melodía
musical
seleccionada
Dentro del Pulsador
Guía de Selección de Tonos
Puerta del frente
Ding-Dong
Westminster
Whittington
Puerta de atrás
Ding
ON
1 2
CR2032
TYPE “C”
TYPE “C”
1 2 3 4 5 6 7 8
CR2032
ON
1 2
TYPE “C”
TYPE “C”
1 2 3 4 5 6 7 8
PRESS & HOLD TUNE - 1 SEC SYNC - 3 SEC RESET - 10 SEC
Puente Apagado Puente Encendido
(Off) (On)