Heath Zenith SECUR360 9305 User manual

To see operational and troubleshooting information and videos,
go to www.hzsupport.com
Dated receipt required for warranty replacement.
FEATURES
• Solar Powered
• Wi- connectivity
• 180° Motion sensor
UNPACKING
Be sure to remove all contents from packaging and verify
all items are present before assembling this light xture.
is package includes the following items:
• Security Light
• Solar Panel
• Owner’s Manual
• SECUR360 App Quick Start Guide
• Mounting Hardware
HARDWARE INCLUDED
Note: Sixmountingbracketscrewsareincluded.einstal-
lation will only require two.Discard the unused mounting
bracket screws after installation.
Screw (x6) Wall Anchor (x6)
© 2020 HeathCo LLC 210451-01A
Connected LED Solar
Security Motion Light
Model: 9305
INITIAL BATTERY CHARGE
IMPORTANT: The solar panel requires full, direct
sunlighttochargethe battery. Clouds,rain,snow,
and other weather conditions may not allow the
solar panel to completely recharge the battery.
Other obstructions suchas buildings ortrees may
block the sun as well.
When installing the solar panel, make sure it is
aimedasdescribedbelowwithaminimumamount
ofobstructions.Ifpossible,mountthepanelfacing
toward the southern sky.

2 To see operational and troubleshooting information and videos,
go to www.hzsupport.com
210451-01
• PRIOR TO USE, the solar panel will need to be con-
nected to the battery (see Installation instructions)
and the battery will require 3 to 7 days of full sun to
completely charge with the control dial in the OFF
position. Remove the rubber plug from the bottom of
the light xture and insert the end of the solar panel cable
into the opening. If possible, aim the solar panel toward
the south and tilt it approximately 50° from horizontal.
If the solar panel cannot be aimed toward the south,then
tilt the panel approximately 30° if possible.
• Actual operating time will vary depending upon how
frequently the light is turned on by the motion sensor.
• Solar lighting isnot designed to equalstandard120V light-
ing.e amount of light output is reduced to allow the sun
time to fully recharge the battery between lighting cycles.
• Solar collectionisonly eectiveindirectsunlight.Every
hour the light is on requires a minimum of 16 hours of
sunlight charging.Solar panels collect less than 10% of
the sun’s energy.
MOUNTING LOCATION
e most important thing to remember for the operation
of your solar powered motion sensing light is that it works
from the power received from direct sunlight. e more
direct sunlight the solar panel receives in a day,the longer
the light will operate.
Solar Light Fixture
e main unit contains the LEDs, motion sensor, and
battery. When deciding where to mount this unit, keep
in mind that the motion sensor that activates the light
has a “eld of vision”of 40 feet (12 meters) in front of the
light and about 180° detection angle at a surrounding air
temperature of 77° F (25 °C).
Solar Panel
e solar panel converts the sun’s energy into electricity,
thus charging the battery stored in the solar light xture.
e solar panel requires direct sunlight falling onto the
face of the solar panel for as long as possible over the
course of the day.
When choosing the location for the solar panel,make sure
it is aimed toward the south and is tilted to a suitable angle
to allow as much direct sunlight to fall upon it as possible.
Make sure there is a minimum amount of obstructions
between the solar panel and the sun.
Also, make sure your solar panel location is not too far
away from the solar light xture for the wires to reach
and connect.
IMPORTANT SAFETY AND
INSTALLATION INFORMATION
Beforeinstallingsecuritylight,readallinstructionscarefully
and keep owner’s manual for future reference.
• CAUTION: To avoid water damage, the motion sensor
controlsmustbefacingthegroundwhen theinstallation
is complete.
• CAUTION: Keep the lamp head 30° below horizontal
to avoid water damage.
• CAUTION: Burn hazard.Allow the light xture to cool
before touching.
• NOTICE: Do not immerse components in liquid.
• is xture is designed for outdoor installation and
should be mounted to a wall or eaves.
• To achieve best results, this xture should be mounted
8 feet (2.4 meters) above the ground. Note: If xture
is mounted higher than 8 ft. (2.4 meters), aiming the
sensor down will reduce coverage distance.
• Do not cut the solar panel wire. Discontinue use if the
wire becomes frayed or broken.
• Do not use any other charging device other than the
single solar charging panel provided with this light.
Doing so may result in injury or damage to the light
and voids any warranty.
• Position the cord so that it is securely fastened and will
not result in a hazard (such as tripping).
e motion sensor on this light xture detects “motion”
by the movement of heat across the coverage area. e
motion sensor is more sensitive to the movement of heat
moving across the coverage area and less sensitive to the
movement of heat directly towards it.
Least Sensitive Most Sensitive
MotionMotion
Sensor

To see operational and troubleshooting information and videos, 3
go to www.hzsupport.com
210451-01
Figure 1
Figure 2
Figure 3
R
E
S
E
T
/ 0 +
217,0(
6HQVLWLYLW\
(FR3RZHU0RGH
2Q 2II
0LQ
7HVW
2II
6
R
E
S
E
T
/ 0 +
217,0(
6HQVLWLYLW\
(FR3RZHU0RGH
2Q 2II
0LQ
7HVW
2II
6
R
E
S
E
T
/ 0 +
217,0(
6HQVLWLYLW\
(FR3RZHU0RGH
2Q 2II
0LQ
7HVW
2II
6
INSTALLATION
Mounting the Solar Light Fixture
Make sure there is enough vertical space above the mounting plate
to allow the light xture to be mounted.
1. Press the bottom tab of the wall mounting plate and slide the
mounting plate from the light body (see Figure1).
2. Placethemountingplateagainstthemountingsurfaceandensure
the mounting plate is level. Mark the hole locations (see Figure
2). Note: e “UP”arrow must point upward.
• If mounting to a wooden surface,drill two 3/32 in. holes into
themounting surface.Installthetwomountingscrewsthrough
the mounting plate and into the mounting surface.
• If mounting to wall board or brick, drill two 7/32 in. holes
into the mounting surface. Insert the wall anchors and attach
the mounting plate using the two mounting screws.
3. Slide the rear of the light xture down onto the mounting plate
until it snaps into place (see Figure 3).
IMPORTANT:
• If wall mounted, make sure the xture is mounted with the sensor
below the lamp head (see above).
• If eave mounted, mount the xture with sensor facing away from
the house wall (see above).Rotate the sensor so the controls on the
bottom of the sensor (see Figure 4) face the ground.
Figure 4
Note: Light xture and sensor should be mounted as shown above
when installed (depending upon type of installation).
Wall Mount Eave Mount
7+,66,'(83
7+,66,'(83
R
E
S
E
T
/ 0 +
217,0(
6HQVLWLYLW\
(FR3RZHU0RGH
2Q2II
0LQ
7HVW
2II
6
R
E
S
E
T
/ 0 +
217,0(
6HQVLWLYLW\
(FR3RZHU0RGH
2Q2II
0LQ
7HVW
2II
6

4 To see operational and troubleshooting information and videos,
go to www.hzsupport.com
210451-01
Figure 8
Figure 5
Figure 6
Figure 7
Mounting the Solar Panel
1. Place the solar panel against the mounting surface and mark the
mounting holes (see Figure 5).
• If mounting to a wooden surface,drill two 3/32 in. holes into
themounting surface.Installthetwomountingscrewsthrough
the base and into the mounting surface.
• If mounting to wall board or brick, drill two 7/32 in. holes
into the mounting surface. Insert the wall anchors and attach
the base using the two mounting screws.
IMPORTANT: Caulk around the base and on top of the screw
heads after installation.
2. Rotate the solar panel to the desired angle (see Figure 5).
IMPORTANT:esolarpanelmustreceiveasmuchdirectsunlight
over the course of the day as possible.Keep in mind that shadows
may block the sunlight from reaching the solar panel during the
day.
3. Carefully route the solar panel cable to the light xture.Plug the
solar panel cable into the connector extending from the bottom
of the light xture (see Figure 6).
IMPORTANT: Slide the ON-TIME switch on the bottom of the
sensor to the OFF position and allow the battery to charge with
3 to 7 days of full sunshine before testing (see Figure 4).
TESTING AND ADJUSTMENTS
CAUTION:To avoid water damage, motion sensor con-
trolsmustbefacingthegroundwheninstallationiscomplete.
LED Indicator
1. Slide the sensitivity (SENS) switch to the “L” position, the
ON-TIMEswitchtotheTESTposition,andtheECOPOWER
MODE switch to the OFF position (see Figure 4).
2. Walk through the coverage area noting where you are when the
lights turn on. Also, the LED indicator behind the motion sen-
sor lens will glow blue when motion is detected (see Figure 8).
Note: e blue LED will turn o 30 seconds after all motion has
stopped.
3. If needed, gently grasp the motion sensor and move it from side
to side or up and down to adjust the detection zone.
4. If needed, gently grasp the lamp head and move it from side to
side or up and down to adjust the light coverage area.

To see operational and troubleshooting information and videos, 5
go to www.hzsupport.com
210451-01
FINAL SETUP
IMPORTANT: All of the settings on the motion sensor are
also controlled through the SECUR360 app. However,
if the light loses wi- connection (the LED indicator
will blink blue), the motion sensor settings will control
the light until wi- connection is reestablished. Once
the light reconnects to wi-, the settings in the app will
control the light.
1. Adjust the sensitivity (SENS) switch as needed (“L”,
“M”,“H”). Sensitivity set too high may increase false
triggering.
2. Set the ON-TIME switch to OFF, 30 seconds, or 2
minutes (the amount of time the light will stay on
after all motion has stopped).
3. SettheECOPOWERMODEswitchtoONorOFF.
See Eco Power Mode section for more information.
4. Go to the App StoreSM or Google Play™ and search
for the “Secur360” app and download. See the
enclosed instruction sheet,“Connecting to your new
SECUR360 device”, for more details.
5. Oncestep4iscomplete,opentheSECUR360appand
log into the account. Use the app to set the controls
for the light xture.
LED Indicator
• RED + Solid: Light is warming up – Stays in this mode
until the light is ready.
• RED + ashing (1 second ON / 1 second OFF): Light
is in wi- connection mode.
• BLUE + ashing: Light is connecting to the internet.
• BLUE + (2 Minutes ON): Light is connected to the
internet.
• BLUE: When motion is detected,the LED will be ON
until all motion has stopped for 30 seconds.
For additional information concerning this light or the
SECUR360app,visitwww.heath-zenith.com/Secur360.
IMPORTANT CONSIDERATIONS
AVOID AIMING THE SENSOR AT:
• Below are examples of objects that might produce heat
and may cause the motion sensor to trigger:
• Pools of Water • Air Conditioners
• Dryer Vents • Animals
• Heating Vents • Automobile Trac
If you suspect that a heat source of this type is triggering
the motion sensor, reduce the sensitivity.
• Areaswherepetsor trac maytriggerthemotionsensor.
• Nearby large, light-colored objects reecting light may
trigger the shut-o feature. Do not point other lights
at the motion sensor.
SEASONAL CHANGES:
e motion sensor works by sensing temperature changes
across its eld of view. e closer the surrounding tem-
perature is to a person’s body heat, the less sensitive the
sensor will appear.e greater the temperature dierence,
the more sensitive the sensor will appear.Use the sensitiv-
ity control in the app to adjust the setting as the outside
temperature changes for the dierent seasons. is is a
normal part of the light sensor’s operation.
ECO POWER MODE
“Eco Power mode” is a selectable feature within the app
designed to increase battery life by reducing certain func-
tions, such as:
• e light will not have constant access to wi-.e wi-
module in the light will only activate after a set amount
of time has passed or whenever the light is activated by
motion.
• e brightness of the light will be reduced.
• Voice activation is turned o.
• When grouped with other lights, this light will not be
turned on when other lights are activated. When this
light is activated,it will turn on other lights in the group.
RESET BUTTON
islight can beresetto the originalfactorysettingseither
by using the reset button on the bottom of the sensor or
throughtheSECUR360app.Note: Afterresettingthelight,
it may take up to 5 minutes for the light to be removed
from the SECUR360 app.
• Reset Button (see Figure 4) – Use a paper clip to press
the RESET button for 15 seconds to reset the light.
For additional information concerning this light or the
SECUR360app,visitwww.heath-zenith.com/Secur360.

6 To see operational and troubleshooting information and videos,
go to www.hzsupport.com
210451-01
CARE AND CLEANING
• To prolong the original appearance, clean the light xture with clear water and a soft, damp cloth only.
• Do not use paints, solvents,or other chemicals on this light xture.ey could cause a premature deterioration of the
nish.is is not a defect in the nish and will not be covered by the warranty.
• Do not spray the light xture with a hose or power washer.
• If not to be used for several weeks, turn the unit OFF.
SPECIFICATIONS
Motion Sensing Range.........................Up to 40 ft. (12 m) [Varies with surrounding temperature].
Motion Sensing Angle .........................Up to 180°
Power Requirements.............................4400 mAh, 3.7V Li-Ion Rechargeable Battery (pre-installed, non-replaceable)
Oine Operating Modes.....................TEST, OFF, and MOTION ACTIVATED
ON-Timer............................................30 seconds or 2 minutes (Night Only)
Test Timer............................................5 Seconds (Day and Night)
Sensitivity (SENS) ...............................“L”, “M”, “H”
LED Lumens .......................................1000
LED color temperature ........................4900K

To see operational and troubleshooting information and videos, 7
go to www.hzsupport.com
210451-01
TROUBLESHOOTING GUIDE
SYMPTOM POSSIBLE CAUSE SOLUTION
e light will not come on. 1. e motion sensor is aimed in the wrong
direction.
2. Battery is weak or dead.
3. Solar panel positioned wrong.
4. Daylight turn-o (photocell) is in eect.
5. e outside air temperature is close to the
same as a person’s body heat.
6. e light has been turned “OFF” using the
app.
7. Surrounding air temperature is greater than
122° F (50° C) or less than -4° F (-20° C).
1. Re-aim the motion sensor to cover the
desired area.
2. Switch the sensor OFF and let the battery
charge for 3 to 7 sunny days before using
again.
3. Position and angle solar panel so that it gets
plenty of direct sunlight for most of the day,
if not the entire day.
4. Recheck after dark.
5. Increase the sensitivity setting. See Seasonal
Changes on page 5 for more information.
6. Use the app to set the light to “AUTO”
mode.
7. Recheck when the surrounding air
temperature is within the specied range.
e light comes on during
the day. 1. e motion sensor may be installed in a relatively dark location.
2. e “ON-TIME” in the app is set to
“TEST”.
1. e light xture is operating normally under
these circumstances.
2. Set the “ON-TIME” in the app to the 30
second or 2 minute setting.
e light comes on for no
apparent reason. 1. e motion sensor may be sensing small animals or automobile trac.
2. Sensitivity is set too high.
3. e outside temperature is much warmer or
cooler than a person’s body heat (summer or
winter).
1. Decrease the sensitivity setting or reposition
the motion sensor.
2. Decrease the sensitivity setting.
3. Decrease the sensitivity setting. See Seasonal
Changes on page 5 for more information.
e lights stay on
continuously. 1. e motion sensor may be picking up a heat source like an air vent, dryer vent, or brightly
painted, heat-reective surface.
2. e light has been turned “ON”using the
app.
1. Decrease the sensitivity setting or reposition
the motion sensor.
2. Use the app to set the light to “AUTO” or
“OFF” mode.
e lights ash on and o. 1. Heat is being reected from other objects
and may be turning the motion sensor on
and o.
2. e “ON-TIME” is in “TEST” mode and
warming up.
3. Battery is almost dead.
1. Decrease the sensitivity setting or reposition
the motion sensor.
2. While in TEST mode, the light only stays
on for 5 seconds. Set the “ON-TIME” in the
app to the 30 second or 2 minute setting.
3. Switch the sensor OFF and let the battery
charge for 3 to 7 sunny days before using
again.
e lights ash once then
stay o in manual mode. e motion sensor is detecting light from the lamp head. Reposition the lamp head to keep the area below the motion sensor relatively dark.
Light is not as bright as
normal. Weak battery. Switch the sensor OFF and let the battery charge for 3 to 7 sunny days before using
again. Once the rechargeable solar battery is
suciently recharged, the light will come on at
full brightness.

8 To see operational and troubleshooting information and videos,
go to www.hzsupport.com
210451-01
ONE YEAR LIMITED WARRANTY
is is a “Limited Warranty”which gives you specic legal rights. You may also have other rights which vary from
state to state or province to province.
For a period of 1 year from the date of purchase,any malfunction caused by factory defective parts or workmanship
will be, at the sole option of HeathCo LLC, either repaired or replaced at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence,light bulbs, batteries,
and other expendable items are not covered by this warranty. Unauthorized service or modication of the product
or of any furnished component will void this warranty in its entirety.is warranty does not include reimbursement
for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. HeathCo
LLC reserves the right to discontinue products and to change specications at any time without incurring any
obligation to incorporate new features in products previously sold.
is warranty covers only HeathCo LLC assembled products and is not extended to other equipment and com-
ponents that a customer uses in conjunction with our products.
THISWARRANTY ISEXPRESSLYINLIEUOFALLOTHERWARRANTIES,EXPRESSOR IMPLIED,
INCLUDING ANY WARRANTY,REPRESENTATION OR CONDITION OF MERCHANT ABILITY
OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFI-
CALLY IN LIEU OF ALL SPECIAL,INDIRECT,INCIDENTAL,OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE
SHALL BE NO LIABILITY ON THE PART OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY
LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
Please keep your dated sales receipt, it is required for all warranty requests.
TECHNICAL SERVICE
Please call 1-800-858-8501 (English speaking only) for assistance before returning product to
store.
If you experience a problem, follow this guide. You may also want to visit our Web site at: www.hzsupport.com. If the
problem persists, call* for assistance at 1-800-858-8501 (English speaking only), 8:00 AM to 5:00 PM CST (M-F).
You may also write* to:
HeathCo LLC
P.O. Box 90045
Bowling Green, KY 42102-9045
ATTN: Technical Service
* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase,
and Place of Purchase.
No Service Parts Available for this Product
Please keep your dated sales receipt, it is required for all warranty requests.

Para ver más información y vídeos sobre operación y resolución de problemas, 9
visite www.hzsupport.com
210451-01
© 2020 HeathCo LLC 210451-01 S
Se necesita elrecibofechado para reemplazo bajo garantía.
CARACTERÍSTICAS
• Funciona con energía solar
• Conectividad Wi-
• Detector de movimiento de 180 °
DESEMPAQUE
Asegúrese de retirar todo el contenido del empaque y
vericar que todos los elementos estén incluidos antes de
ensamblar este aparato de luz. Este paquete incluye los
siguientes elementos:
• Luz de seguridad
• Panel solar
• Manual del propietario
• Guía de inicio rápido de la aplicación SECUR360
• Ferretería de montaje
FERRETERÍA INCLUIDA
Nota: Se incluyen seis tornillos para el soporte de montaje.
La instalación sólo requiere dos.Deseche los tornillos del
soporte de montaje no utilizados luego de la instalación.
Tornillo (x6) Ancla de expansión
de pared (x6)
Luz LED de seguridad con
detección de movimiento
activada con energía solar
conectada
Modelo: 9305
CARGA INICIAL DE LA BATERÍA
IMPORTANTE: El panel solar requiere luz de sol
directa y total para cargar la batería. Condiciones
climatológicas como nubes, lluvia, nieve y otros
puedenevitarqueelpanelsolarrecarguecomple-
tamente la batería. Otros obstáculos tales como
ediciosoárbolestambiénpuedenbloquearelsol.
Al instalar el panel solar, asegúrese de que esté
orientado como se describe a continuación con
una mínima cantidad de obstáculos. De ser posi-
ble, monte el panel con dirección al cielo sureño.

10 Para ver más información y vídeos sobre operación y resolución de problemas,
visite www.hzsupport.com
210451-01
• ANTESDESUUSO,elpanelsolardebeserconectado
a la batería (vea las instrucciones de instalación) y
la batería requerirá de 3 a 7 días de pleno sol para
cargarse por completo con el disco de control en
la posición OFF. Retire el tapón de caucho de la parte
inferior de la lámpara e inserte el extremo del cable del
panel solar en la abertura. Si es posible, apunte el panel
solar hacia el sur e inclínelo por casi 50° del nivel ho-
rizontal (vea la ilustración en la siguiente página). Si al
panel solar no se le puede apuntar hacia el sur,entonces
incline el panel por casi 30° si es posible.
• El tiempo real de funcionamiento dependerá de cuan
frecuentementeel detectordemovimientoprendelaluz.
• La luz solar no se iguala al alumbrado estándar de 120
voltios.La cantidad de producción de luz se reduce para
permitirque el sol recargue porcompletolabatería entre
los ciclos de alumbrado.
• La colección solar es solo efectiva bajo la luz directa del
sol. Por cada hora que la luz está prendida requiere un
mínimo de 16 horas de carga de luz solar. Los paneles
solares recolectan menos del 10% de la energÌa solar.
LOCALIZACIÓN DEL MONTAJE
Lacosamás importantequehayque recordarparalaopera-
cióndesulámparadetectorademovimientoalimentadapor
luzsolares quetrabajaconlaenergía recibidadirectamente
del sol. Mientras el panel solar más directamente recibe
la luz solar durante un día, más tiempo funcionará la luz.
Lámpara Solar
La unidad principal contiene LEDs, detector de movi-
miento y baterías. Cuando se decida dónde instalar la
unidad,recuerde que el detector de movimiento que activa
la luz tiene un “campo de visión”de 40 pies (12 metros) al
frente de esta luz y más o menos un ángulo de detección de
180º a una temperatura del aire ambiente de 77ºF (25ºC).
Panel Solar
El panel solar convierte la energía solar en electricidad,
cargando así a la batería guardada en la lámpara solar. El
panelsolarrequierequelaluzsolar incida directamenteenla
superciedelpanelelmayortiempoposiblealolargodeldía.
Cuando escoja el sitio para el panel solar, asegúrese que
este panel esté apuntando hacia el sur e inclinado a un
ángulo adecuado que permita que incida directamente
tanta luz solar como sea posible. Asegúrese que haya la
menorcantidaddeobstruccionesentreelpanelsolaryelsol.
También asegúrese que la ubicación de su panel solar no
esté demasiado alejada de la lámpara solar para que los
cables puedan alcanzar y conectarse.
INFORMACIÓN IMPORTANTE DE
SEGURIDAD E INSTALACIÓN
Antes de instalar la luz de seguridad,lea todas las instruc-
cionescon cuidado y guardeel manual del propietario para
futura referencia.
• PRECAUCIÓN:Paraevitardañosporelagua,loscontroles
del detector de movimiento deben estar de cara al suelo
cuando la instalación esté terminada.
• PRECAUCIÓN: Mantenga lo portabombilla inclinados
a 30° por debajo de la línea horizontal para evitar daños
por el agua.
• PRECAUCIÓN: Peligro de quemaduras. Deje que el
aparato de luz se enfríe antes de tocarlo.
• AVISO: No sumerja los componentes en líquidos.
• Este aparato está diseñado para una instalación al aire
libre y se lo debe montar en una pared o en aleros.
• Para lograr los mejores resultados, este aparato debe
montarse a 8 pies (2,4 metros) por encima del suelo.
Nota: Si el aparato está instalado a más de 8 pies (2,4
m), si se apunta el detector hacia abajo se reducirá la
distancia de cobertura.
• No corte el cable del panel solar.Deje de usar si el cable
se deshilacha o se rompe.
• No use ningún otro dispositivo de carga que no sea el
panel de carga solar sencillo provisto con esta lámpara.
Si usa otro dispositivo, puede producirle una lesión o
un daño a la lámpara y anular cualquier garantía.
• Coloque el cordón para que esté sujeto de forma segura
y no resulte peligroso (como una desconexión).
El detector de movimiento de este aparato de luz detecta
“movimiento” debido al movimiento del calor a través
del área de cobertura. El detector de movimiento es más
sensible a la circulación del calor que se mueve a través
del área de cobertura y menos sensible a la circulación del
calor que va directamente hacia él.
Lo menos sensible Lo más sensible
Detector
Movimiento Movimiento