Heath Zenith Secure Home UT-9260-BZ User manual

© 2009 HeathCo LLC 598-1342-01
Mo t i o n Se n S i n g
Ha l o g e n Se c u r i t y li g H t
Model
UT-9260-BZ

-2- 598-1342-01
Contents
Introduction................................................................................................... 3
Package Contents...................................................................................... 4
Installation ..................................................................................................... 5
Wall Mount................................................................................................ 5
Eave Mount ............................................................................................... 5
Crossbar Mounting Bracket..................................................................... 6
Standard Wiring ....................................................................................... 6
Controlling Non-Motion Sensing Fixtures.............................................. 7
Finish Mounting ....................................................................................... 8
Specications ............................................................................................ 8
Test and Adjustment..................................................................................... 9
Expected Coverage .................................................................................10
Operation .....................................................................................................12
Troubleshooting Guide...............................................................................13
Lifetime Warranty .......................................................................................14

-3-
598-1342-01
Introduction
Enhanced Performance Features
☞Rugged gripping teeth and finger screw provide full three-dimension adjustment of sensor head.
☞Five silicon rubber gaskets seal internal components and controls from severe environmental
conditions.
☞Stainless steel screws to prevent rust and corrosion.
☞Built in 1.25 Mega Watt surge protection.
☞A.S.I.C. (Application Specific Integrated Circuit) design allows more reliable performance.
☞Range Boost option to extend range for those hard to cover areas.
☞Extremely wide angle coverage (up to 270°). Adjustable with built-in lens shields.
☞Easy to control other lights with your fixture (up to 1000 Watts total load).
☞Expanded lens area receives more infrared light improving detection sensitivity.
☞Pulse count technology reduces false sensing from wind and rain for professional reliability.
☞Automatic photocell deactivates unit in daylight to save energy.
☞Power outage reset. Turns light off automatically if turned on by power interruption or electrical storm.
☞Selectable light timer to set the time lights stay on after motion has been detected.
☞Range control allows adjustment of coverage range.
☞Manual override to turn lights on/off at your convenience with existing indoor wall switch.
Dear Consumer:
We would like to thank you for purchasing this product. You have purchased the most durable
motion sensing security light available today. This product will give you many years of reliable service.
We are so confident with the durability of this product that it is backed with a lifetime warranty.

-4- 598-1342-01
Package Contents
• MotionSensorLightFixture
• Two250watthalogenlamps
• Manual
• HardwarePack
1 Gasket
 1 Hanger
1 Crossbar Mounting Bracket
4 Wire nuts
2 #6-32 X 3/4" screws
(for small rectangular boxes)
2 #8-32 X 3/8" screws
(for circular or octagon boxes)
2 #10-24 X 1/2" screws
(for water tight boxes)
1 M5 X 0.8 X 40 mm screw
(fixture to mounting bracket)
1 Rubber Plug
Estimated Installation Time: 30 minutes
Items needed for installation (not included):
• Phillipsandatheadscrewdrivers
• Pliers
• Wirestrippers/cutters
• Ladder
• Safetyglasses
• Siliconecaulk
Fits All Junction Box Configurations
Circular
Horizontalrectangular
Vertical rectangular
Octagon

-5-
598-1342-01
Installation
• IfyouwanttousetheManualOverridefeatureyouwillneedtoinstallthextureonacircuitcon-
trolled by a switch.
• The lamps are packed in boxes, inside the lampheads. Open the lampheads by removing the screws
at the top. Use a clean cloth or the foam packing around the lamps to keep your fingers off the lamps.
Install the lamps in the right side of the sockets first, then the left. Close the lampheads and continue
the installation as shown below.
❒ Loosenthethumbscrewsholdingthesensor
head and lampheads.
❒Adjust the various parts so that the fixture
looks similar to this illustration.
❒Finger tighten the thumbscrews at this time.
Wall Mount Eave Mount
❒ Loosenthethumbscrewsholdingthesensor
head and lampheads.
❒ Adjust the various parts so that the fixture
looks similar to this illustration.
❒ Finger tighten the thumbscrews at this time.
CAUTION: To Avoid Fire Or Burn Hazards:
•Allowxturetocoolbeforetouching.Thebulbandthexture
operate at high temperatures.
•Keepxtureatleast3"(76mm)fromcombustiblematerials.
Do not aim at objects closer than 3' (1 m).
•UseonlytypeT250W(max.)tungstenhalogen120VAC
lamps.
WARNING: BefoRe stARtING the INstAllAtIoN, tuRN the poWeR off At the
cIRcuIt BReAkeR.

-6- 598-1342-01
CAUTION: If you have not already turned the
power off at the breaker or fuse, do so now.
Connect the junction box wires to the fixture wires.
Twist together and secure with wire connectors.
CAUTION: If you are not controlling additional
fixtures from your security light fixture, DO NOT
connect the RED wire or remove wire connector.
Standard Wiring
Black to
Black
White to
White
Mounting
Bracket
Green ground
wire to junc-
tion box
ground wire
RED, not
used in most
applications
Gasket
Mount Fixture with Crossbar
Mounting Bracket
❒ Turn power off at the fuse or circuit breaker.
❒Remove the existing light fixture (if appli-
cable).
❒Install the mounting bracket as shown using
two screws supplied in hardware pack that fit
your junction box:
Rectangular Junction Box - Use two #6-32
x 3/4" screws.
Circular or Octagonal Junction Box - Use
two #8-32 x 3/8" screws.
Watertight Junction Box - Use two #10-24
x 1/2" screws.
❒The plastic hanger can be used to hold the fix-
ture while wiring. The small end of the plastic
hanger can be threaded through the hole in the
center of the cover plate. The small end then
goes into one of the slots on the mounting
bracket.
❒ RoutetheLightControl’swiresthroughthe
large gasket holes.
Junction Box

-7-
598-1342-01
Controlling Non-Motion Sensing Fixtures
❒When wiring to additional standard fixture
only: Strip the motion sensor's red wire and
connect to the standard fixture's black wire.
Connect all white wires together. Total fixture
ratings must not exceed 1000 Watts (8.3 A).
NOTE: All wiring between fixtures should be run
in accordance with the National Electrical
Code (Canadian Electrical Code in Canada)
through conduit or another acceptable means.
Contact a qualified electrician if there is any
question as to the suitability of the system.
❒This fixture is provided with a sensor rated
for 1000 Watts. Since the fixture is only rated
500 Watts, 500 Watts of additional load may
be controlled by this sensor.
❒When determining what a fixture is rated for,
do not simply look at the rating on the lamp in
thexture.Lookatthemarkingwhichspeci-
fies the maximum lamp wattage for which the
fixture is suitable.
❒ Once you have selected the fixtures to be con-
nected and determined their maximum ratings,
add these ratings up. For instance, if you have 3
fixtures rated 100 Watts, 150 Watts, and 75 Watts
respectively, you have a total load of 325 Watts.
Wiring to a Motion Light & Standard Fixture
Standard
Fixture
RED from Security Light to
BLACK from Fixture
BLACK from Switch to
BLACK from Security Light
WHITE from Line
to WHITE from
Security Light
WHITE from Line to
WHITE from Fixture

-8- 598-1342-01
Finish Mounting
❒Align the cover plate, gasket, and the mounting
bracket hole. Secure with M5 x 0.8 x 40 mm
mounting screw supplied.
❒Push the rubber plug firmly into place.
❒If not installed on a weatherproof box, caulk
between the cover plate and mounting sur-
face with silicone weather sealant.
To obtain maximum lamp
life, keep the tubular
lamps horizontal.
Specifications
Range .............................. 70 feet (21.0 m); 100 feet
(30.5 m) with Range Boost.
Varies with surrounding tem-
perature.
Sensing Angle ................. Up to 270° (Adjustable)
FixtureLoad.................... Up to 500 Watts Maximum
Tungsten Incandescent [Up
to 250 Watts Maximum each
lamp holder.]
SensorLoadCapacity ..... Up to 1000 Watts (8.3 amps)
Maximum Tungsten Incan-
descent
Power Requirements ....... 120VAC,60Hz
Operating Modes............. TEST,AUTOandMANUAL
MODE
Time Delay...................... 1, 5, 20 minutes
CAUTION:To Avoid Fire Or Burn Hazards:
•Allowxturetocoolbeforetouching.Thebulbandthexture
operate at high temperatures.
•Keepxtureatleast3"(76mm)fromcombustiblematerials.
Do not aim at objects closer than 3' (1 m).
•UseonlytypeT250W(max.)tungstenhalogen120VAC
lamps.
HeathCo LLC reservestheright todiscontinue
products and to change specifications at any time
without incurring any obligation to incorporate new
features in products previously sold.
Rubber Plug

-9-
598-1342-01
Test and Adjustment
NOTES: When first turned on or when switching
from Manual to Auto mode wait 1 1/2
minutes for the unit to calibrate.
Testing with Range Boost on during day-
light may result in abnormal operation.
❒Turn on the circuit breaker and light
switch.
❒Open the control access cover(onbottomofunit)
by pulling down on the tab of the metal door.
❒ Turn the Range control to the center of its adjust-
ment and the ON-TIME to TEST position.
Sensor Bottom
Do not aim the sensor at:
• Objectsthatchangetemperaturerapidly,such
as heating vents and air conditioners, to help
avoid false triggering.
• Wherepets or traffic may trigger the control.
• Nearby large, light-colored objectsreecting
light may trigger the shut-off feature. Do not
point other lights at the sensor.
B
O
O
S
T
MIN
TEST 1 5 20
RANGE
MAX
ON-TIME

-10- 598-1342-01
Adjustments Continued . . .
Aim Sensor Down
for Short Coverage
❒ Loosenthetwothumbscrews.Estimatethedirectiontoaimthesensor
and tighten the thumbscrews just enough to hold the sensor in place.
NOTE: The top screw allows the sensor to rotate side to side. The bot-
tom screw allows the sensor to rotate up and down.
❒Walk through the coverage area noting where you are when the lights
turnon(also,theLEDwillashseveraltimeswhenmotionisdetected).
Loosenthethumbscrewsandreadjustthesensorasnecessary.Tighten
the thumbscrews (finger tight) when you are satisfied with the coverage
direction. Keep the sensor at least 1 inch (25 mm) from lamps and
keep the controls facing downward.
❒Adjust RANGE as needed to increase or decrease the range. Too much
sensitivity may cause false triggering in some environments.
❒For maximum range, the sensor must be aiming straight out.
❒Set the amount of TIME (1, 5, or 20 minutes) you want the lights to stay
on after motion is detected at night.
❒Release the tab on metal door to allow door to close.
Aim Sensor Out for
Long Coverage
Expected Coverage
The sensor is less sensitive to motion directly
towards it, most sensitive to motion across its
field of view.
Motion
Sensor
Least Sensitive Most Sensitive
When mounted 8 feet (2.4 m) from the ground, you
may expect the range shown below. If mounted
much higher the sensor may miss objects near the
ground. If mounted much lower the sensor range
may be reduced.
Motion Maximum Range
(Sensor aiming straight out)
8 ft.
(2.4 m)
70 ft. (21.0 m) 100 ft. (30.5 m)
With RANGE With RANGE
Set to MAX Boosted