Heatrae Sadia Aquatap User manual

Aquatap (Boil only model)
Simple installation guide

BOTTOM
WASTE DRAIN
TOP WASTE DRAIN
AQUATAP
DISPENSER
MESH COVER
WASHER
FIXING SCREW
DRIP TRAY
FIXING SCREW
STUD EXTENDER
CLAMPING BAR
DISPENSER “C” CLAMP
AND NUT
SPACER
DISPENSER CONNECTOR
FIXING NUT
WASHER
STUD
3mm
Aquatap – tap installation Heater installation
Tap with drip tray
installation
Tap only installation
Securing the
drip tray
Ø35.5
Ø35.5
Ø125
Tap with drip tray
(use template)
Ø35.5
Ø35.5
Ø125
Tap only
The dispensing tap supplied
is suitable for mounting onto
a worktop or counter surface.
It should be positioned such
that it discharges into a sink
or drip tray.
Air circulation must be provided so air
can flow through the cupboard. Failure
to do this may result in the Aquatap
not performing correctly.
Minimum clear space requirement
Ventilation
150mm 150mm
150mm 150mm
150mm
150mm
70mm*
70mm
70mm
70mm*70mm*
70mm*
70mm
150mm 150mm
150mm 150mm
150mm
150mm
150mm 150mm
150mm 150mm
150mm
150mm
70mm*
70mm
70mm
70mm*70mm*
70mm*
70mm
150mm 150mm
150mm 150mm
150mm
150mm
Front view
Top view

FUSED
SPUR
HEATER UNIT
AQUATAP DISPENSER
MAINS
WATER SUPPLY
DISPENSING
CABLE
FLEXIBLE
HOSE
HOT TAP
OUTLET HOSE
A
A
TAP VENT HOSE
A
ISOLATING
VALVE
(NOT SUPPLIED)
Vent and
outlet hoses
(all pipes should
be cut as short
as possible and
rise continuously)
Heater installation
Commissioning details overleaf...

HEATER COMMISSIONING
• Ensure that all electrical, water and vent pipe connections have been correctly made and are secure.
• Turn on the water and electrical supplies to the Aquatap heater.
• The unit is now in the ‘commissioning’ mode, this will take 30 minutes, during this time DO NOT use
the unit or dispenser.
• Once commissioning has completed the ready light on the dispenser tap is solid and the unit can be
used.
• The heater unit and dispenser tap should be flushed to remove any installation residue.
• On first use there may be air in the pipework, this will clear after a few uses.
USING THE DISPENSER
When the Aquatap is ready to dispense water the LED marked ‘ready’ will illuminate. To get a flow of water:
• Press the button marked ‘Safety’ (the safety light will flash).
• Press and hold the red hot water button (the safety light will illuminate solid).
• Take the required amount of boiling water then release the red button (the safety light will go off).
• If you wish to dispense more boiling water return to the first step.
EXPLANATION TO THE USER
• After commissioning the following should be explained to the user:
- Correct operation of the Aquatap water heater and dispensing tap.
- The position of the water and electrical isolation points.
- How to identify a malfunction of the unit.
- Necessity for regular maintenance.
• The commissioning record in the full operating and maintenance instructions should be completed
and then these left with the user for future reference.
Heatrae Sadia Heating Hurricane Way Norwich Norfolk NR6 6EA
T: 0844 871 1535 F: 0844 871 1528 E: [email protected] www.heatraesadia.com/heateam
Heatrae Sadia Heating may introduce modifications to their products from time to time. Consequently, the details given in this brochure are subject to alteration without notice.
36006254 issue 1
Commissioning guide
COMMISSIONING
00:30
IF FURTHER PRODUCT DETAILS ARE REQUIRED THE FULL OPERATING
AND MAINTENANCE MANUAL SHOULD BE REFERRED TO.
READY LED
BOILING WATER
LED
FIGURE 12 : LED POSITIONS (DISPENSER)
SAFETY BUTTON
HOT WATER
BUTTON
READY LED
BOILING WATER
LED
FIGURE 12 : LED POSITIONS (DISPENSER)
SAFETY BUTTON
HOT WATER
BUTTON
CHILLED/AMBIENT
WATER BUTTON