Heiman HEIEHS1CG-P User manual

Heiman
Smart Combustible Gas Sensor (LPG)
SKU: HEIEHS1CG-P
Quickstart
This is a Alarm Sensor for Europe. To run this device please connect it to your mains power supply. Press the Network Button 3 times within 1.5s, Green
LED is Blinking 3 times within 1 second.
If add Process is successful, Green LED will turn on.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer,
distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this
equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and
every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is
not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-
Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this
device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level
of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The smart combustible gas sensor is designed to detect propane (C3H8), and sound alarm to remind people of the danger, it can also send notification to users‘
smart phone via gateway to remind of people remotely. it adopts Z-Wave wireless transmission technology. With the characteristics of high sensitivity and
stablization, it can avoid fire or explosion happened in advance.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do
this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended
to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
-Long press Net_Button at least 10 seconds in the device.
-Device Reset Locally notification is Transmitted.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the
assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Installation
Liquefied petroleum gas:
Should be installed at 0.3-1m height from floor and semi-conductor of sensor installation position to gas source should be less than 1.5m.

Should be installed at 0.3-1m below from the ceiling, semi-diameter to gas source less than 1.5m.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the
devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
Press the Network Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.
If add Process is successful, Green LED will turn on.
Exclusion
P th N t k B tt 3 ti ithi 1 5

Product Usage
1. Shell surface will be slightly hot while working, which is normal phenomenon
2. Please dismantle sensor while decorating house
3. Avoid spraying aerosol around sensor
4. Oil adhesion around gas convection holes may effect the sensitivity of gas sensor after a long time of use. It‘s suggested to clear gas convention holes every 3
months (with a little detergent, but with care so it doesn‘t enter the body of the sensor).
5. Semi-conductor of gas sensor has 5-year lifespan
6. Don‘t use lighter to test the sensor directly
Starting up
The green LED lights up after power on the sensor, when a beep sounds once, the sensor enters into warm-up state then red and yellow LED flashes alternately.
Eventually, the flash stops 3 minutes later, which indicates that the sensor has entered into normal working state. Don‘t the senor while it‘s in warm-up state.

LIGHT STATE & PRODUCT TEST
STATE COLOR LIGHT ALARM
SOUND
Power Green Normally on No
Alarm Red Flashing gas alarm
Malfunction Yellow Normally on Long buzz
Test button of this sensor is used for testing wheater LED indicator and buzzer can work properly. Red LED and yellow LED flash alternatively with buzzer alarm
when the test button is pressed.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are
always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:

Group Number Maximum
Nodes Description
11 Lifeline association group
Include command classes: Notification Report and Device Reset Locally notification.
25 Root Device group(Notification).
Notification reports status of gas detected or no gas detected via Lifeline.
When the sensor detects status change of gas detected and no gas detected, the device will
be triggered.
Technical Data

Dimensions 78 x 78 x 68 mm
Weight 91 gr
Hardware Platform ZM5202
EAN 4251295701769
IP Class IP 20
Voltage 230V
Device Type Notification Sensor
Network Operation Always On Slave
Z-Wave Version 6.51.09
Certification ID ZC10-16125343
Z-Wave Product Id 0x0260.0x8003.0x1000
Communications Protocol Z-Wave Serial API
Color White
Communications Connections Ethernet (Wireless/WiFi)
Electric Load Type
IP (Ingress Protection) Rated ok
Sensors
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Supported Command Classes
Association Grp Info
Association V2
Device Reset Locally
Manufacturer Specific V2
Notification V7
Powerlevel
Version V2
Zwaveplus Info V2
Explanation of Z-Wave specific terms
Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall
controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.
(c) 2021 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwave.eu. The template is maintained by Z-Wave
Europe GmbH. The product content is maintained by Z-Wave Europe GmbH , Supportteam, [email protected]. Last update of the product data: 2021-06-09
14:43:50