Heiman HM-807DWP User manual

Digital Passive Infrared Motion Detector Manual
FEATURES
PRODUCT PROFILE INSTALLTION HINTS
Mount flat on a wall
Mount indoor
Outdoor
Mount in a corner
Wall mount
Mount near fluttering curtains
Aiming at windows
Mount in direct sunlight
Mount near
heat or cold sources,
beneath rotating objects
＞0°
Angle downwards
Pet immunity loss
With objects (1.8m) ahead
Pet immunity loss
PRODUCT INTRODUCTION
TECHNICAL SPECIFICATIONS
1
INSTALLATION CONDITIONS
1. For good pet immunity performance, the installation height is
recommended not lower than 2m. Mount the detector flat on a
wall or in a corner. Do not angle it downwards.
2. Avoid placing the detector in outsides, near a air-conditioner or
a heat source, in direct sunlight, beneath a rotating object and
near fluttering curtains. Do not place objects about 1.8m high
in front of the detector, that a pet can jump onto and pet
immunity will be reduced.
3. Surface of installation should be firm with no vibration.
4. Mount the detector where an intruder passes easily.
This product is with high
stability. It adopts dual sensor signal processing technology and
provides superhigh detection and anti false alarm
performance,and MCU processing ensuring its reliability from
the design basis. Any intruder passing through the detection area,
the detector will automatically detect the movements of human
body and pets.If Any dynamic movement, it will send the alarm
signal to the mainframe.This product is suitable for the safety in
residential areas, villas,factories, shopping malls, warehouses and
office buildings etc.
digital infrared motion detector
Consumption Current:≤18mA
Detecting Distance: 12 m
Detecting Angle: 110 degrees
Detecting Speed:0.3m/s~ 3m/s
PIR sensitivity adjustment availability
Adjustable immunity
Self-Testing Time: 60s
Alarm Delay Time: 3s/30s optional
Alarm Indication: Red LED with on / off availability
Sensor: Double element pyroelectrie infrared sensor
Operating Temperature: -10°C ~ +50°C
Wired connection feeding 12 volts
Environment Humidity: Max 95% RH (no
Anti-RF interference:10MHZ~1GHz 20v/m
Installation Mode: Wall or corner mount
Alarm Output: NC/NO optional, contact rated at DC28V 100mA
Tamper Output: NC, contact rated at DC28V 100mA
congelation)
● EN 50130 certified
● MCU control, high efficience of anti false alarm
● Dual Sensor technology,real pet-immunity
● Immunity(25kgs)
● Dual-mode Temperature Compensation
● Dynamic Thresholds Adjustment Technology
● Bipolar Pulse Count Adjustable
● Anti White Light Interference, Anti RF Interference
● Fresnel Lens
● Alarm Output N.C./N.O. Optional
● Alarm Delay Time Optional (3s/30s)
● SMT Manufacture Technology, Stabler Performance
● Wall mounted
WIRING INSTRUCTIONS
Red wire: positive DC power
Black wire: negative DC power
Yellow wire: tamper output
White wire: alarm output

INSTALLATION STEPS
OPERATING INSTRUCTION
NOTICE
1.Install the detector on a suitable position. Cut off the thin
plastic in the bracket if open wire installed.
2. Connect the power wire and signal wire as wiring
instruction.
3. Screw the detector into the bracket (the click sound says
well-installed).Adjust the install angle as needed.
INSTALLATION ILLUSTRATIONS
1. Function setting （ refer to figure three ）
(1) Pulse jumper :Adjust the pulse count to change the sensitivity
and anti RF interference ability.
Short 1&2: Class 1 pulse, high sensitivity and strong anti RF
interference, adapt to general environment.
Short 2&3: Class 2 pulse, low sensitivity and stronger anti RF
interference, adapt to the environment with serious RF
interference.
Factory setting is Short 1&2 (class 1 pulse).
(2) Relay jumper: Choose N.C./N.O. to set the status of alarm output.
You can choose the different output in
accordance with the alarm mainframe.
Short 1&2: N.O. ( normally open)
Short 2&3: N.C. (normally closed)
Factory setting is Short 2&3 N.C.(normally closed)
(3) Delay jumper： Alarm delay time is the duration of the alarm
indicator before alarm.
Short 1&2: delay 3 sec.
Short 2&3: delay 30 sec.
Factory setting is Short 1&2, delay 3 sec.
(4) LED jumper：
For setting LED ON/OFF, no effect to the detect normal work.
LED can be shut off for the concealment of the detector after
test.
2.Product testing
Turn on the power and the indicator on. The detector comes into
auto-check status for about 60 sec. LED indicator turns off
and the detector comes into normal detecting status.The
tester should walk parallel with the wall installed detector in the
testing area. LED indicator turns on, which indicates the detector
is in alarm status.
JUMPER SETTING FIGURE
123123
open
2&3
1&2
1RELAY jumper 2
LED jumper
3
DELAY jumper
4
PULSE jumper
1234
1. Please install and use the detector as the manual instructed.
Any detector failure, please inform management center or our
company after-sales service center for repair.
2.The product can reduce accident, but cannot ensure no risk at
all. For your safety, in addition to the proper use of this
product, remain vigilant in your daily life and strengthen
security prevention consciousness.
3.In order to guarantee it can work well, the power should be
kept to supply and conducted walking test periodically. Once
a week is suggested.
DETECTING AREA VIEW
Side view
Platform
2
Digital Passive Infrared Motion Detector Manual