Helion CONQUEST 10 SC XB User manual

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
Quick-Start
Guide
Product specications are subject to change without notice.
Due to ongoing development, the actual product may vary from
images shown.
This product contains chemicals known to the State of California
to cause cancer, birth defects and other reproductive harm.
This product is not a toy! (14+) Recommended for ages 14 and
up. Adult supervision required for ages under 18 years old.
Contains small parts, keep out of reach of children 3 years of
age and younger.
To download the full Owner’s Manual & Technical
Information Guide, please visit:
www.Helion-RC.com
or scan the QR code with your smart phone.
Distributed in the
UK by:
J Perkins Distribution Ltd,
Lenham,
Kent, UK
ME17 2DL.
www.jperkins.com
Distributed in Australia by:
Model Engines (Aust.) Pty. Ltd.,
P.O. BOX 828
NOBLE PARK 3174
Australia
www.modelengines.com.au
Ph [phone]
[email protected]
Distributed in the US by:
Firelands Customer Service/Product Support
1133 Libra Drive, Lincoln, NE 68512
www.relandsgroup.com
1-800-205-6773
customerservice@relandsgroup.com
HLNA0764 Conquest 10SC XB (US)
HLNA0774 Conquest 10SC XB (UK-EU)
HLNA0784 Conquest 10SC XB (AU)
MADE IN CHINA

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
1Remove the components from
the box and ensure the contents
are correct:
• 1 x Conquest 2WD Vehicle
• 1 x 2000mAh 6-cell NiMH
battery pack
• 1 x IKONNIK ET3 2.4GHz
3-channel transmitter
• 1 x 6-cell wall charger
• 1 x Quick-Start Guide.
2Remove the four body clips from
the car and lift the body clear.
3Locate the battery cradle in the
center of the car, release the hook
and loop tape and withdraw the
battery pack.
4Plug the charger into a wall
socket, connect the battery to the
charger and place the battery on
a non-ammable surface. Switch
the wall socket ON noting that
a fully discharged battery will
be charged in approximately 3
hours. Periodically monitor the
temperature of the battery when
charging and disconnect if it
exceeds 120°F (49°C). Unplug
the battery when charged.

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
5Re-insert the fully charged battery
pack into the cradle and tightly
secure it with the hook and loop
straps.
6Remove the battery cover from the
underside of the ET3 transmitter
and insert four AA alkaline cells.
Take care to ensure that the
correct polarity is observed.
7Ensure the radio switch is in the
OFF position, then connect the
battery to the ESC.
8Replace the body and secure it
with the four body clips.
9Switch ON your IKONNIK ET3
transmitter and ensure the LED is
lit solid red and that no alarms are
audible. Ensure that the CH2 EPA
dials are turned fully clockwise
and that the D/R (steering rate)
dial is centered. Ensure, also, that
the CH1 and CH2 (trim) dials are
centered at zero.
LED
CH2 EPA D/R
CH1 &
CH 2
Trim

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
11 Check the operation of the throttle
and steering. Pulling the throttle
trigger back will drive the car
forward, pushing the trigger forward
once will apply the brakes while
pushing the trigger forward twice
will drive the car in reverse. Turning
the wheel to the right will cause the
car to turn right and vice versa.
12 Use the throttle and steering trim
dials to ne-tune the controls of
your car. In doing so, ensure that
your Conquest tracks in a straight
line. Also that it doesn’t creep
forwards or backwards at zero
throttle.
Locate the switch and turn ON
your Conquest. In the unlikely
event that the car does not
operate, see the PAIRING /
BINDING instructions at the back
of this guide
10

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
1Remove the body and locate the
IKONNIK Krypton receiver.
2Place your Conquest and ET3
transmitter in close proximity but
not less than 12” (300mm) apart.
Having followed steps 1 to 10, in the unlikely event that your car does not operate please
follow the 5 stage pairing process detailed here.
Pairing / Binding The Transmitter
3Press and hold the PAIR / BIND
button on the receiver then switch
the receiver on. The receiver’s
LED will ash to indicate that it is
in PAIR / BIND mode.
5When the LED on the receiver
lights solid red your ET3
transmitter and Conquest will
be bound. You will now have full
control of throttle and steering.
Return to Step 11 of this guide to
complete the set-up of your car.
4Press and hold the PAIR / BIND
button on the transmitter then
switch the transmitter on. Release
the PAIR / BIND button only when
the transmitter’s LED begins
ashing.
300mm

REPLACEMENT PARTS
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
Replacement Parts
HLNA0970 ......... Rear Chassis Plate: B, ST, MT
HLNA0971 .........R-Clip: B, ST, MT
HLNA0972 ......... Nuts (M4): B, ST, MT
HLNA0973 ......... Column Head Hex Screw, M3x8: B, ST, MT
HLNA1125 .........Wheel Hexes - SC
HLNA0975 ......... Nuts (M3): B, ST, MT
HLNA0976 ......... Radio Tray Mount: B, ST, MT
HLNA0978 ......... Shock (Rear): B, ST, MT
HLNA0979 ......... Shock Ball Head, C: B, ST, MT
HLNA0980 .........Pin 2x10: B, ST, MT
HLNA0981 .........Differential Planetary Gear: B, ST, MT
HLNA0982 .........Differential Shaft: B, ST, MT
HLNA0983 .........Differential Outdrive: B, ST, MT
HLNA0984 .........Differential O-Ring: B, ST, MT
HLNA0985 .........Flat Head Hex Screw, M3x14: B, ST, MT
HLNA0986 .........Flat Head Hex Screw, M3x12: B, ST, MT
HLNA0987 .........Flat Head Hex Screw, 3x8: B, ST, MT
HLNA0988 .........Flat Head Hex Screw, 2x10: B, ST, MT
HLNA0990 .........Suspension Arm E-Clips, 0.6mm: B, ST, MT
HLNA0991 .........Flat Head Hex Screw, 3x10: B, ST, MT
HLNA0992 .........Cap Head Hex Screw, 3x10: B, ST, MT
HLNA0993 .........Cap Head Hex Screw, 3x12: B, ST, MT
HLNA0994 .........Cap Head Hex Screw, 3x5: B, ST, MT
HLNA1117 ......... Bumper (Front) - SC
HLNA1118 .........Bumper (Rear) - SC
HLNA1119 .........F/R Bumper Holder - SC
HLNA1003 .........Battery Strap: B, ST, MT
HLNA1116 .........Chassis - SC
HLNA1005 .........Lower Suspension Arm (Front): B, ST, MT
HLNA1006 .........Lower Suspension Arm (Rear): B, ST, MT
HLNA1007 ......... Chassis Plate (Front): B, ST, MT
HLNA1008 .........Shock Tower (Front): B, ST, MT
HLNA1009 .........Shock Tower (Rear): B, ST, MT
HLNA1010 ......... Steering Hub Carrier (L/R): B, ST, MT
HLNA1011 .........Hub Carrier (Front L/R): B, ST, MT
HLNA1012 .........Upright (Rear): B, ST, MT

REPLACEMENT PARTS
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
HLNA1013 .........Bulkhead Brace (Front): B, ST, MT
HLNA1014 ......... Shock Mount (Front): B, ST, MT
HLNA1015 .........Upper Link (Front), 58.5mm: B, ST, MT
HLNA1016 ......... Steering Link, 55mm: B, ST, MT
HLNA1017 .........Upper Link (Rear), 73mm: B, ST, MT
HLNA1018 .........Servo Link, 30.5mm: B, ST, MT
HLNA1019 .........Gearbox: B, ST, MT
HLNA1020 .........Motor Guard: B, ST
HLNA1021 .........Main Gear Cover: B, ST, MT
HLNA1022 .........Differential Case, 48P: B, ST, MT
HLNA1023 .........Gear, 34T-48P: B, ST
HLNA1024 .........Gear, 81T-48P: B, ST
HLNA1025 .........Wing Mount: B
HLNA1026 .........Shock Absorber (Front): B, ST, MT
HLNA1027 .........Arm Bulkhead (Rear): B, ST, MT
HLNA1028 .........Arm Bulkhead (Front): B, ST, MT
HLNA1031 .........Steering Sway Arm Assembly: B, ST, MT
HLNA1032 .........Gear, 20T-48P: B, ST, MT
HLNA1033 .........Slipper Shaft: B, ST, MT
HLNA1034 .........Slipper Pad: B, ST, MT
HLNA1035 .........Slipper Hub: B, ST, MT
HLNA1036 .........Slipper Tensioner Spring: B, ST, MT
HLNA1037 ......... Motor Mount: B, ST, MT
HLNA1123 .........Axle set, Rear - SC
HLNA1040 .........Dogbone: B, ST, MT
HLNA1041 ......... Suspension Pin (Front / Rear): B, ST, MT
HLNA1042 .........Servo Saver Assembly: B, ST, MT
HLNA1043 .........Ball Head Screws, 5.8mm: B, ST, MT
HLNA1124 ......... Axle set, Front - SC
HLNA1045 .........Steering Shaft Bush: B, ST, MT
HLNA1053 .........Gear, 23T-48P: B, ST, MT
HLNA1054 .........Lower Suspension Arm Screws (Front) 3x25mm: B, ST, MT
HLNA1055 .........Lower Suspension Arm Screws (Rear) 3x29mm: B, ST, MT
HLNA1056 .........Pin, 3x26: B, ST, MT
HLNA1057 .........Pin, 5x18: B, ST, MT
HLNA1059 .........Powder Steel Gear, 20T-48P: B, ST, MT
HLNA1061 .........Shock Absorber (Rear): B, ST, MT

REPLACEMENT PARTS
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
HLNA1062 .........Body Post: ST, MT
HLNA1063 .........Post Mount: ST, MT
HLNA1120 .........Wheels - SC
HLNA1121 .........Tire (Front): ST
HLNA1067 .........Tires, L/R - SC
HLNA1122 .........L/R Tires, Mounted - SC
HLNA1070 ......... Cap Head Hex Screw, 3x14: B, ST, MT
HLNA1071 ..........Cap Head Hex Screw, 3x16: B, ST, MT
HLNA1072 ......... Hex Grub Screws, M3x3: B, ST, MT
HLNA1126B.......Replacement Body, SC Blue
HLNA1126R ...... Replacement Body, SC Red
HLNA1126Y .......Replacement Body, SC Yellow
HLNA1126G ...... Replacement Body, SC Green
HLNA1086 .........Conquest Battery, 7.2V, 6-Cell, 2000mAh NiMH: B, ST, MT
HLNA1088 .........Steering Turnbuckle (Front) 55mm: B, ST, MT
HLNA1089 .........Turnbuckle (Front Arm): B, ST, MT
HLNA1090 .........Steering Turnbuckle (Front) 74mm: B, ST, MT
HLNA1091 .........Serrated Axle Nuts: B, ST, MT
HLNA1092 .........Aluminum Axle Drive Hexes: B, ST, MT
HLNA1093 .........Aluminum Pivot (Front): B, ST, MT
HLNA1094 .........Aluminum Pivot Block (Rear): B, ST, MT
HLNA1095 .........Aluminum Chassis Brace (Front): B, ST, MT
HLNA1096 .........Aluminum Pivot Plate (Front): B, ST, MT
HLNA1097 ......... Aluminum Pivot Plate (Rear): B, ST, MT
HLNA1098 .........Shock (Front / Rear): B, ST, MT
RDNA0086 ........ Metric 12 550 HT Brushed Motor: ST XB, MT XB
HLNA0059 .........ESC, Brushed, 30-15 WP with Reverse: ST XB, MT XB
KNNS0024 ........ET3 3-Channel 2.4GHz (Krypton) - Transmitter and All Weather Receiver
NOTE: If you experience any problems,
please consult online troubleshooting guide.