HELLER PED75G User manual

Instruction Manual
75cm High Velocity
Pedestal Fan
Model: PED75G
READ AND SAVE THESE INSTRUCTIONS

Please read and follow the instructions in this user manual even if you feel you are familiar with the product,
and find a place to keep it handy for future reference.
For your convenience record the complete model number (located on the product identification plate) and
the date you received the product, together with your purchase receipt and attach to the warranty and
service information. Retain in the event that warranty service is required.
NOTE: The rating of this product (as marked on the product identification plate) is based on specific loading
tests. Normal use or the use of other recommended attachments may draw significantly less power.
Important Safeguards
When using any electrically powered product, basic safety precautions should always be followed, including
the following:
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT
WARNING!: - to reduce the risk of fire, electrical shock or injury to persons or property:
•Always operate the product from a power source of the same voltage, frequency and rating as
indicated on the product identification plate.
•Fully assemble the fan before switching on.
•The fan must not be used if the guards are not fastened according to instructions.
•Remove the unit from its packaging and check to make sure it is in good condition before using.
•Do not let children play with parts of the packaging (such as plastic bags).
•Close supervision is necessary when the product is used by or near children or infirm persons. Do not
allow children to use it as a toy.
•Do not operate any product with a damaged cord or plug, or after the product malfunctions, or is
dropped or appears damaged in any way. Return the complete product to the place of purchase for
inspection, repair or replacement.
•Before unplugging the power cord, be sure to turn the power off. When touching the unit, be sure
your hands are dry to prevent electrical shock.
•Adjustable pole must not be extended past 1.1m high.
•Avoid making contact with moving parts. Never insert fingers, pencils or any other objects through
the guards whenever the power plug is connected, especially while the unit is working.
•Always place the fan on a stable, level surface when operating to prevent the fan from overturning.
Do not run the power cord under carpet. Do not cover the power cord with throw rugs or runners.
Route the power cord away from walking paths so that nobody can trip over it. The cable should be
kept away from heat, sharp edges and oil.
•Your pedestal fan should be placed away from heat sources such as; radiators, gas/electric heaters
and direct sunlight.
•Ensure that the fan is switched off from the supply mains before removing the guard.
•To reduce the risk of electric shock, do not immerse or expose the product or flexible cord to rain,
moisture or any liquid other than those necessary for correct operation of the product.
•This product should not be used in the immediate vicinity of water, such as bathtub, washbowls,
bathroom swimming pool etc. Where the likelihood of immersion or splashing could occur.
•Switch off and unplug from outlet when not in use, before assembling or disassembling parts and
before cleaning. Remove by grasping the plug - do not pull on the cord.
•Be sure that no other high current appliances are plugged into the same circuit as your fan, as an
overload can occur.
•Do not remove any fixed covers.
•Avoid the use of an extension cord as the extension cord may overheat and cause a risk of fire.

•Do not use the appliance for other than its intended use.
•Do not use outdoors. FOR INDOOR USE ONLY.
•Do not leave the appliance unattended when switched on.
•Do not cover the grill, or operate in close proximity to curtains etc.
•The use of attachments or accessories not recommended or sold by the product distributor may
cause personal or property hazards or injuries.
•Ensure that the fan is switched off from the supply mains before removing the guard.
•Use this fan as described in this manual. Any other uses, not recommended by the manufacturer,
may cause fire, electric shock, or injury to persons and may void the warranty.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a person responsible for their safety.
•The installation of a residual current device (safety switch) is recommended to provide additional
safety protection when using electrical appliances. It is advisable that a safety switch with a rated
residual operating current not exceeding 30mA be installed in the electrical circuit supplying the
appliance. See your electrician for professional advice.
Parts Location

Before First Use
Before use, remove all packaging and inspect the appliance for any damage. If there appears to be any
damage, please take the unit back to place of purchase for a replacement.
Assembly Instructions
Base Assembly:
1. Loosen the screw from the adjustable pipe.
2. Put the pipe into the centre hole of the base.
3. Tighten the screw by placing the decorative ring onto the adjustable pipe
and fix it into place.
Motor Assembly:
1. Unscrew the connecting stopper screw of the adjustable pipe.
2. Fix and lock the motor and adjustable pipe by connecting the stopper
screws.
Rear Grill Assembly:
1. Loosen the four screws fixed on the front of the motor housing.
2. Align the four holes of the rear grill to the four holes on the motor
housing.
3. Fix and lock the screws.
Fan Blade Assembly:
1. Place the fan blade into the bottom of the motor axis.
2. Use the screw provided to fix and lock the blade.
Front Grill Assembly:
1. Connect the front grill with the rear grill. The screw hole
must be aligned with the front and rear grill.
2. Fasten the clips.
PLEASE NOTE: Adjustable pole must not be extended past 1.1m high.

Operating Instructions
Before inserting the plug into a power outlet, make sure that the correct voltage being used corresponds to
what is indicated on the rating label, and that the socket has an earth facility.
1. Once the wall fan is assembled and installed, plug the cord into an acceptable power source.
2. The fan has three speeds: 1 –Low, 2 –Medium, 3- High and 0 –Off.
3. To turn the wall fan ‘On’, turn the knob to the desired setting. To turn the wall fan ‘Off’ turn the knob
to ‘0’.
Oscillating Function:
WARNING: Before using the oscillating
function, always turn the fan ‘Off’ and
wait until the fan blades come to a
complete stop.
The diagram on the left hand side,
show the underneath of the fan’s
Motor unit. In the position shown; i.e.
Position 1 (Oscillation), the fan head
will swing side to side during operation.
To fix the fan head to blow air in a fixed
direction, first turn off and unplug the
fan, then unscrew the ‘Nut’ and screw
it into the other hole –Position 2 (No
Oscillation).
Tilt Function:
WARNING: Before using the tilt function, always turn the fan ‘Off’ and wait until the fan blades come to a
complete stop.
You can tilt your fan head ‘Up’ or ‘Down’ by following the below steps.
1. Use one hand to hold the fan head, and use your other hand to loosen the rotating joint bolt (refer
to below diagram).
2. Tilt the fan head to the desired angle, and tighten the rotating joint bolt.

Care & Cleaning
To make cleaning easier, you can dismantle some parts of your fan.
1. Switch the fan ‘Off’ and unplug the power supply before cleaning.
2. Use only a soft damp cloth to clean the fan.
3. Do not immerse the fan in water or any other liquids, and never allow water to drip into the motor
housing.
4. Do not use gasoline, paint thinner or other chemicals to clean the fan.
5. To clean the fan blade, use 2 screw drivers to disengage the hooks (8 hooks) holding the front grille
to the rear grille.
6. Remove the front grille.
7. Wipe the blade and grille.
8. Check that the fan blade screw is tight.
9. Reassemble the fan by snapping the front grille into place.
10. Store the fan in its original box or cover the fan to protect it from dust. Store in a cool dry place.
Disposal
Environmental Protection
Waste electrical production should not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local Authority or retailer for recycling
advice.
Loosen the rotating joint bolt to tilt the
fan head ‘Up’ or ‘Down’.

Specifications
Model
Description
Voltage
Frequency
Wattage
PED75G
75cm High Velocity Pedestal Fan
220-240V~
50Hz
220W

Australian Customer Service
GAF Control (Sales) Pty Ltd
P.O Box 19
Altona North Victoria 3025
Phone: [phone]
Hours: 9am-5pm (EST) Mon-Fri
www.gafcontrol.com.au
*This product may vary slightly to the product illustrated due to ongoing product development.