Hendi Salamander User manual

You should read this user manual carefully before using the appliance.
SALAMANDER
HND299630

2
Keep these instructions with the appliance.
For indoor use only.

3
Dear Customer,
Thank you for purchasing this Hendi appliance. Before using the appliance for the first time, please read
this manual carefully, paying particular attention to the safety regulations outlined below.
Safety regulations
• This appliance is intended for commercial use.
• The appliance must only be used for the purpose for which it was intended and designed.
The manufacturer is not liable for any damage caused by incorrect operation and im-
proper use.
• Keep the appliance and electrical plug away from water and any other liquids. In the
event that the appliance should fall into water, immediately remove plug from the socket
and do not use until the appliance has been checked by a certified technician. Failure to
follow these instructions could cause a risk to lives.
• Never attempt to open the casing of the appliance yourself.
• Do not insert any objects in the casing of the appliance.
• Do not touch the plug with wet or damp hands.
• Danger of electric shock! Do not attempt to repair the appliance yourself. In case of
malfunctions, repairs are to be conducted by qualified personnel only.
• Never use a damaged appliance! Disconnect the appliance from the electrical outlet and
contact the retailer if it is damaged.
• Warning! Do not immerse the electrical parts of the appliance in water or other liquids.
Never hold the appliance under running water.
• Regularly check the power plug and cord for any damage. If the power plug or power cord
is damaged, it must be replaced by a service agent or similarly qualified persons in order
to avoid danger or injury.
• Make sure the cord does not come in contact with sharp or hot objects and keep it away
from open fire. To pull the plug out of the socket, always pull on the plug and not on the
cord.
• Ensure that the power cord is positioned so that it will not cause a trip hazard.
• Always keep an eye on the appliance when in use.
• Warning! As long as the plug is in the socket the appliance is connected to the power
source.
• Turn off the appliance before pulling the plug out of the socket.
• Never carry the appliance by the cord.
• Do not use any extra devices that are not supplied along with the appliance.
• Only connect the appliance to an electrical outlet with the voltage and frequency men-
tioned on the appliance label.
• Connect the power plug to an easily accessible electrical outlet so that in case of emer-
gency the appliance can be unplugged immediately. To completely switch off the appli-
ance pull the power plug out of the electrical outlet.
• Always turn the appliance off before disconnecting the plug.

4
• Never use accessories other than those recommended by the manufacturer. Failure to do
so could pose a safety risk to the user and could damage the appliance. Only use original
parts and accessories.
• This appliance is not intended for use by persons (including children) with reduced phys-
ical, sensory or mental capabilities, or lack of experience and knowledge.
• This appliance must not be used by children under any circumstances.
• Keep the appliance and its cord out of reach of children.
• Always disconnect the appliance from the mains if it is left unattended or is not in use,
and before assembly, disassembly or cleaning.
• Never leave the appliance unattended during use.
Special safety regulations
• Use the appliance as described in the manual.
• This appliance should be operated by trained personnel in kitchen of the restaurant,
canteens or bar staff, etc.
• Keep hands, hair, clothing, spatulas and other utensils away during operation to reduce
the risk of injury to persons and/or damage to the machine.
• Danger of burns! Do not touch surfaces of the appliance while in use. The surfaces
of appliances become hot during use.
• Allow the appliance to completely cool down before cleaning.
• Make sure there is a clearance of 15 cm is maintained at the left, right & top of the appli-
ance for ventilation purposes.
• Never place this appliance near combustibles.
• Warning: Wear gloves (not included) with heat insulation. Do not touch the body during
operation to prevent scalding.
For mounting on the wall, please read carefully below important safety warnings:
• Verify prior to installation that the wall can safely support the combined loading of the
appliance and the food that put inside the appliances for cooking.
• Make sure that no electrical wires, water, gas or other lines are located around the in-
stallation location.
• Consult a qualified contractor or installer for assistance if you are not certain about the
structure of the wall.
• Tighten the screws firmly but do not over tighten. Over tightening can damage the screws,
greatly reducing the holding power.
• During mounting, keep away the pet and children.
• Warning! Do not place any objects on the top surface of the appliance to prevent over-
loading.

5
Intended use
• This appliance is intended for professional use.
• The appliance is designed only for grilling or
heating up dishes or sandwiches. Any other use
may lead to damage of the appliance or personal
injury.
• Operating the appliance for any other purpose
shall be deemed a misuse of the device. The user
shall be solely liable for improper use of the de-
vice.
Grounding Installation
This appliance is classified as protective class I and
must be connected to a protective ground.
Grounding reduces the risk of electric shock by
providing an escape wire for the electric current.
This appliance is equipped with a cord having a
grounding wire with a grounding plug. The plug
must be plugged into an electrical outlet that is
properly installed and grounded.
Preparations before first use
• Check to make sure the appliance is undamaged.
In case of any damage, contact your supplier im-
mediately and do NOT use the appliance.
• Remove all the packing material.
• Clean the body, grid and crumb tray with luke-
warm water, a mild detergent and a soft cloth.
Don’t clean the heating elements.
• Level the appliance.
• Make sure that a clearance of 15 to 20 cm is
maintained left and right of the appliance for ven-
tilation purposes.
• Position the appliance in such a way that the plug
is accessible at all times.
• Keep the packaging for storing your appliance
when not in use for extended period of time.
ATTENTION! After cleaning the appliance must be
turned on for 30 minutes without anything in it. Any
smoke or odours produced during this procedure
are normal. Please ensure sufficient ventilation.
After the 30 minutes let the machine cool down and
rinse the grid in water and dry all parts. Don’t clean
the heating elements.
Preparations before wall mounting
Before installation: check the salamander and it’s
brackets for any damage. Note: mounting screws
and tools are not included
• Important: make sure the appliance is mounted
within the reach of the electrical outlet.
• Important: do not mount the salamander on dry-
wall or paneling without first anchoring to a wall
stud!
• Important: Before starting mounting, make sure
you have all the tools, such as screw driver, elec-
tric drills, measuring tape, marking pencil (All
are not included).
• The hinged distance is about 380mm between the
screws.
• The salamander must be securely anchored on
a wall by attaching two of the brackets with 1/4”
bolts to the centre of an interior vertical wall stud
and the other two brackets to the wall using 1/4”
expanding toggle bolts. (not included)
• Locating wall studs: anchoring the brackets on a
wall stud assures that your salamander will not
pry loose during operation. Wall studs are spaced
either 16 or 24 inches on center running floor to
ceiling as part of a wood structure’s framing. It is
recommended to use an electric stud finder (sold
separately) to locate wood (or steel) studs more
quickly and accurately for the location where you
want to mount the salamander. Note: be aware
that items such as ducts, electrical wires and
water pipes may be behind the walls in your work
area. Special care when installing fasteners.
• For attaching the salamander securely to other
wall surfaces such as concrete or brick, see your
local hardware store for recommendations on
using the appropriate concrete and masonry fas-
teners and anchors for your particular structure.
• After you have mounted the bolts, simply slide in
the salamander from the top onto the bolts.

6
Use
• Connect the plug with an electrical socket.
• Place the crumb tray in the appliance.
• Rotate the temperature dial (lower dial) to start
heating.
• The orange light will go on until the desired tem-
perature is reached.
• Rotate the timer to the desired time.
• The green light will go on until the desired time
is reached.
Note: The orange light might go on when the tem-
perature drops, the machine will start reheating till
the desired temperature is reached again.
Cleaning and maintenance
• After use, unplug the appliance from the power
socket and let it cool down.
• Clean the inside and outside of the body, grid and
crumb tray with luke-warm water, a mild deter-
gent and a soft cloth. Don’t clean the heating el-
ements.
• Use a brush to remove any encrustations from
the grid.
• Dry all parts with a dry cloth before storing the
salamander.
• Note! Do not clean the appliance with aggressive
chemicals or abrasives in order to prevent dam-
age to the surface.
Trouble shooting
If the appliance does not function properly, please check the below table for the solution. If you are still unable
to solve the problem, please contact the supplier/service provider.
Problem Possible cause Solution
Turn temperature dial in the off posi-
tion and power light stays on
Fuse broken Contact the supplier.
Power is connected but the salaman-
der doesn’t heat up.
Check if the overheating protector is
malfunctioning
Contact the supplier.
Indicator light doesn’t work while the
salamander is heating up.
Indicator light not connected Contact the supplier.
Indicator light broken Contact the supplier.
Technical specifications
Item HND299630
Operating voltage & frequency 240V~ 50Hz
Rated power 2000W
Protection class Class I
Waterproof protection class IPX4
Timer setting range 30 mins
Temperature setting range 50 °C to 300 °C
Net weight (approx.) 14kg
Remarks: Technical specification is subjected to change without prior notification.

7
Important notice to UK users
This appliance is fitted with a UK approved mains
plug and a 13A fuse. Should the fuse need to be re-
placed, an ASTA or BSI approved BS1362 fuse, rated
at 13A must be used. If the plug needs replacing,
ensure that the fuse is removed beforehand. Always
dispose of defunct plugs and fuses immediately.
Warranty
Any defect affecting the functionality of the ap-
pliance which becomes apparent within one year
after purchase will be repaired by free repair or re-
placement provided the appliance has been used
and maintained in accordance with the instructions
and has not been abused or misused in any way.
Your statutory rights are not affected. If the appli-
ance is claimed under warranty, state where and
when it was purchased and include proof of pur-
chase (e.g. receipt).
In line with our policy of continuous product devel-
opment we reserve the right to change the product,
packaging and documentation specifications with-
out notice.
Discarding & Environment
When decommissioning the appliance, the prod-
uct must not be disposed of with other household
waste. Instead, it is your responsibility to dispose to
your waste equipment by handing it over to a des-
ignated collection point. Failure to follow this rule
may be penalized in accordance with applicable
regulations on waste disposal. The separate col-
lection and recycling of your waste equipment at
the time of disposal will help conserve natural re-
sources and ensure that it is recycled in a manner
that protects human health and the environment.
For more information about where you can drop off
your waste for recycling, please contact your local
waste collection company. The manufacturers and
importers do not take responsibility for recycling,
treatment and ecological disposal, either directly
or through a public system.

Manufacturer: Hendi B.V.
Innovatielaan 6
6745 XW De Klomp, The Netherlands
Tel: [phone]
Email: [email protected]
Importer: Neville UK PLC
Unit 6, Viking Way. Erith, Kent.
DA8 1EW, England
https://www.nevilleuk.com/
Hendi HK Ltd.
1208, 12/F, Exchange Tower
33 Wang Chiu Road, Kowloon Bay, Hong Kong
Tel: [phone]
Email: [email protected]
Find Hendi on internet:
www.hendi.eu
www.facebook.com/HendiToolsforChefs
www.linkedin.com/company/hendi-food-service-equipment-b.v.
www.youtube.com/HendiEquipment
- Changes, printing and typesetting errors reserved.
© 2021 Hendi B.V. De Klomp - The Netherlands Ver: 14-04-2021