Hewlett Packard Enterprise Aruba 6200F User manual

Aruba 6200F Switch Series Installation
and Getting Started Guide
Part Number: 5200-6885a
Published: June 2020
Edition: 2

© Copyright 2020 Hewlett Packard Enterprise Development LP
Notices
The information contained herein is subject to change without notice. The only warranties for Hewlett
Packard Enterprise products and services are set forth in the express warranty statements accompanying
such products and services. Nothing herein should be construed as constituting an additional warranty.
Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Condential computer software. Valid license from Hewlett Packard Enterprise required for possession, use,
or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software
Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under
vendor's standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard
Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise
website.
Acknowledgments
Intel®, Itanium®, Optane™, Pentium®, Xeon®, Intel Inside®, and the Intel Inside logo are trademarks of Intel
Corporation in the U.S. and other countries.
Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Adobe® and Acrobat® are trademarks of Adobe Systems Incorporated.
Java® and Oracle® are registered trademarks of Oracle and/or its aliates.
UNIX® is a registered trademark of The Open Group.
All third-party marks are property of their respective owners.

Chapter 1 About this document...................................................................... 5
Applicable products........................................................................................................................................5
Related publications.......................................................................................................................................5
Chapter 2 Introducing the switches............................................................... 6
Front of the switches......................................................................................................................................6
Network ports......................................................................................................................................7
Management ports............................................................................................................................. 7
Console Port............................................................................................................................. 7
Auxiliary (Aux) port.................................................................................................................. 7
Switch and port LEDs.......................................................................................................................... 8
LED mode select button and indicator LEDs................................................................................... 9
Reset buttons.....................................................................................................................................10
Out-of-band management (OOBM) port........................................................................................10
Back of the switches.....................................................................................................................................10
Power connector............................................................................................................................... 11
Switch features............................................................................................................................................. 11
Chapter 3 Installing the switch......................................................................13
Shipping the switch in a rack...................................................................................................................... 13
Included parts............................................................................................................................................... 13
Installation procedures for 6200F switches.............................................................................................. 14
Installation precautions and guidelines......................................................................................... 15
Prepare the installation site.............................................................................................................15
Verify that the switch boots correctly............................................................................................. 16
Disconnect power from the switch................................................................................................. 16
Mount the switch.............................................................................................................................. 16
Mounting a switch on a tabletop or desktop..................................................................... 17
Mounting the switch in a two-post rack..............................................................................18
Mounting the switch in a four-post rack............................................................................. 18
Connect the switch to a power source........................................................................................... 18
(Optional) Install transceivers..........................................................................................................19
Connect network cables...................................................................................................................19
SFP+ installation notes.................................................................................................................................20
Sample network topologies........................................................................................................................ 21
Chapter 4 Getting started with switch conguration..............................24
Recommended minimal conguration......................................................................................................24
Chapter 5 Troubleshooting............................................................................. 25
Basic troubleshooting tips...........................................................................................................................25
Diagnosing with the LEDs............................................................................................................................26
Proactive networking................................................................................................................................... 32
Hardware diagnostic tests...........................................................................................................................32
Testing the switch by resetting it.....................................................................................................32
Checking the switch LEDs..................................................................................................... 32
Contents
Contents 3

Checking console messages................................................................................................. 32
Testing twisted-pair cabling............................................................................................................. 33
Testing switch-to-device network communications......................................................................33
Testing end-to-end network communications.............................................................................. 33
Restoring the factory default conguration..............................................................................................33
Downloading new switch software............................................................................................................ 34
Chapter 6 Specications..................................................................................35
Environmental specications......................................................................................................................35
Electrical........................................................................................................................................................ 35
Acoustics........................................................................................................................................................36
Safety............................................................................................................................................................. 36
Connectivity standards................................................................................................................................ 38
Chapter 7 Cabling and technology information........................................ 39
Cabling specications.................................................................................................................................. 39
Technology distance specications............................................................................................................ 41
Installing the patch cord.............................................................................................................................. 42
Twisted-pair cable/connector pin-outs......................................................................................................42
Straight-through twisted-pair cable for 10 Mbps or 100 Mbps network connections............. 43
Cable diagram........................................................................................................................ 43
Pin assignments..................................................................................................................... 44
Crossover twisted-pair cable for 10 Mbps or 100 Mbps network connection.......................... 44
Cable diagram........................................................................................................................ 44
Pin assignments..................................................................................................................... 45
Straight-through twisted-pair cable for 1000 Mbps network connections................................45
Cable diagram........................................................................................................................ 45
Pin assignments..................................................................................................................... 46
Chapter 8 Websites...........................................................................................47
Chapter 9 Support and other resources...................................................... 48
Accessing Aruba Support............................................................................................................................ 48
Accessing updates........................................................................................................................................48
Warranty information.................................................................................................................................. 49
Regulatory information............................................................................................................................... 49
Documentation feedback............................................................................................................................49
4Aruba 6200F Switch Series Installation and Getting Started
Guide

This document is intended for network administrators and support personnel.
NOTE: The display and command line illustrated in this document are examples and might not
exactly match your particular switch or environment.
The switch and accessory drawings in this document are for illustration only, and may not
exactly match your particular switch and accessory products.
Applicable products
Aruba 6200F 24G 4SFP+ Switch (JL724A)
Aruba 6200F 24G Class4 PoE 4SFP+ 370W Switch (JL725A)
Aruba 6200F 48G 4SFP+ Switch (JL726A)
Aruba 6200F 48G Class4 PoE 4SFP+ 370W Switch (JL727A)
Aruba 6200F 48G Class4 PoE 4SFP+ 740W Switch (JL728A)
Related publications
•Start Here: Installation, Safety, and Regulatory Information for the Aruba 6200F Switches and Accessories
• ArubaOS-CX software manuals
•Power Over Ethernet (PoE/PoE+) Planning and Implementation Guide
•Transceiver Guide
To view and download these publications, visit the Aruba Support Portal at https://
asp.arubanetworks.com/downloads.
Chapter 1
About this document
Chapter 1 About this document 5

Aruba multiport switches are store-and-forward devices oering low latency for high-speed networking.
Certain switch models also support Power over Ethernet (PoE) technologies and full network management
capabilities.
This chapter describes these switches with the following information:
• Front of the switches:
◦Network ports
◦Management ports
◦LEDs
◦Buttons
◦Out-of-Band Management (OOBM)
◦SFP+ support
• Back of the switches:
◦Power connectors
• Switch features
Front of the switches
Figure 1: Front of all the 6200F switches
1
25 26 27 28
Console
Mgmt
Aux
Spd Stk UID
Reset
Spd: Soli d = Max SpeedSpd: Flas hing = Not Max Spee d 4p 10G SFP Stk: Dim = Oth er MembersStk: Soli d = This Member #S tk: Flashing = Co mmander
LED Mode
1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 5 16 17 18 19 20 21 22 23 24
2
25 26 27 28
Console
Mgmt
Aux
PoE Spd Stk UID
Reset
Spd: Soli d = Max SpeedSpd: Flas hing = Not Max Spee dPoE: Solid = Po E EnabledPoE: Flash ing = Fault/Over Budget 4p 10G SFP Stk: Dim = Oth er MembersStk: Soli d = This Member #S tk: Flashing = Co mmander
LED Mode
1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 5 16 17 18 19 20 21 22 23 24
4
3
49 50 51 52
Console
Mgmt
Aux
1 2 3 4 5 6 7 8 9 10 11 12 13 1 4 15 1 6 17 18 19 20 21 22 2 3 24 2 5 26 27 28 29 30 31 32 33 34 35 36 37 3 8 39 40 41 42 44 46 47 4843 45
Spd: Soli d = Max SpeedSpd: Flas hing = Not Max Spee d 4p 10G SFP Stk: Dim = Oth er MembersStk: Soli d = This Member #S tk: Flashing = Co mmander
LED Mode
Spd Stk UID
Reset
4
49 50 51 52
Console
Mgmt
Aux
1 2 3 4 5 6 7 8 9 10 11 1 2 1 3 14 15 16 17 18 19 20 21 2 2 23 24 2 5 26 27 28 2 9 30 31 32 3 3 34 35 36 3 7 38 39 40 41 42 44 46 47 4843 45
Spd: Soli d = Max SpeedSpd: Flas hing = Not Max Spee d
PoE: Solid = Po E EnabledPoE: Flash ing = Fault/Over Budget 4p 10G SFP
Stk: Dim = Oth er MembersStk: Soli d = This Member #S tk: Flashing = Co mmander
LED Mode
PoE Spd Stk UID
Reset
4
5
49 50 51 52
Console
Mgmt
Aux
1 2 3 4 5 6 7 8 9 10 11 1 2 1 3 14 15 16 17 18 19 20 21 2 2 23 24 2 5 26 27 28 2 9 30 31 32 3 3 34 35 36 3 7 38 39 40 41 42 44 46 47 4843 45
Spd: Soli d = Max SpeedSpd: Flas hing = Not Max Spee d
PoE: Solid = Po E EnabledPoE: Flash ing = Fault/Over Budget 4p 1 0G SFP
Stk: Dim = Oth er MembersStk: Soli d = This Member #S tk: Flashing = Co mmander
LED Mode
PoE Spd Stk UID
Reset
4
Chapter 2
Introducing the switches
6Aruba 6200F Switch Series Installation and Getting Started
Guide

Table 1: Front of all the 6200F switches: Label and description
Label Description
1JL724A Aruba 6200F 24G 4SFP+
2JL725A Aruba 6200F 24G Class4 PoE 4SFP+ 370W
3JL726A Aruba 6200F 48G 4SFP+
4JL727A Aruba 6200F 48G Class4 PoE 4SFP+ 370W
5JL728A Aruba 6200F 48G Class4 PoE 4SFP+ 740W
Network ports
Table 2: Network ports
Switch 10/100/1000 BASE-T PoE
Class 4
10/100/1000 BASE-T SFP+
JL724A - 24 4
JL725A 241- 4
JL726A - 48 4
JL727A 481- 4
JL728A 482- 4
1 370W total PoE available
2 740W total PoE available
NOTE: For supported transceivers, see the latest version of the Transceiver Guide on the Aruba
Support Portal.
Management ports
Console Port
There is a single serial console port on the switch, using a USB Type-C connector. This port is used to
connect a console to the switch. Use a common USB to USB-C cable (must be data capable). A Bluetooth
dongle is available to provide an alternative way of managing and conguring your switch using a mobile
app.
The console can be a PC or workstation running a VT-100 terminal emulator, or a VT-100 terminal.
Auxiliary (Aux) port
An auxiliary port is available for downloading switch software code. This port uses a USB Type-A connector.
Chapter 2 Introducing the switches 7

Switch and port LEDs
Figure 2: Switch and port LEDs
49 50 51 52
Console
Mgmt
Aux
4
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 44 46 47 4843 45
Spd: Solid = Max SpeedSpd: Flashing = Not Max Speed
4p 10G SFP
Stk: Dim = Other MembersStk: Solid = This Member #Stk: Flashing = Commander
LED Mode
PoE Spd Stk UID
Reset
1 8 9765432
Table 3: Switch and port LEDs: Labels and description
Label Description
1 Switch port LEDs
2 PoE LED1
3 Speed mode selected LED
4 Stk LED
5 Reset button
6 UID (Unit Identication)
7 Global Status LED
8 Mode select button
9 OOBM port LED
1 Only on switches that support PoE
Table 4: Front panel LED behavior
Switch LEDs Function State Meaning
PoE LED Indicates Port LEDs are
showing PoE
information (not
applicable for non PoE
switches)
O PoE mode not selected
On - Green PoE mode selected
Slow Flash - Amber One or more ports
experiencing PoE failure.
PoE mode not selected.
On - Amber One or more ports
experiencing PoE failure.
PoE mode selected.
Spd LED Indicates Port LEDs are
showing speed
information
O Speed mode not selected
On - Green Speed mode selected
Not Implemented No fault dened
Table Continued
8Aruba 6200F Switch Series Installation and Getting Started
Guide

Switch LEDs Function State Meaning
Stk LED Indicates Port LEDs are
showing stacking mode
information
O Stacking mode not selected
On - Green Stacking mode selected
On - Amber One of the switch is
experiencing stacking
failure. Port LEDs will be
used to indicate the number
of the stacking member.
Slow ash Amber A port has a stacking failure.
Stacking mode not selected
UID LED Locator LED O User congured the located
LED : OFF
On/Flash Blue (for 30
min)
User congured the locator
LED: On/Flash
Global Status Indicator
LED
Overall status of the
product
Flash - Green Self-test in progress during
UBOOT and SVOS
On - Green Successfully booted
ArubaOS-CX
Flash - Amber Recoverable faults (e.g. fans,
PSU fault)
On - Amber Critical faults (e.g. exceed
temperature limit)
Snoring (Dim - Bright
periodically)
System is in hibernation
OOBM Status Indicator
LED
Status of OOBM Link
connectivity
O OOBM port is not
connected, no link
established
Half Bright - Green OOBM port is enabled and
established link with partner
On - Green Experiencing high
bandwidth utilization
Activity Flicker - Green % of the time that the LED
light up is roughly
proportional to the % of full
bandwidth utilization of the
port
* Press the Mode Select button to switch between PoE, Spd, or Stk Mode.
LED mode select button and indicator LEDs
The state of the switch port LEDs is controlled by the LED Mode select button. The current view mode is
indicated by the mode LEDs next to the button. To step from one view mode to the next, press the button to
cycle through the dierent modes.
Chapter 2 Introducing the switches 9

Reset buttons
The Reset button is recessed from the front panel. (This design protects it from being pushed accidentally.)
The button is accessible through small holes on the top of the front panel. Use pointed objects, such as
unbent paper clips, to push it.
To accomplish this: Do this: This will happen:
Soft reset Press and release the Reset
button.
The switch operating system is
cleared gracefully. The switch then
reboots and runs self-tests.
Hard reset Press and hold the Reset button
for more than 5 seconds, then
release.
The switch reboots, similar to a
power cycle. A hard reset is used,
for example, when the switch CPU
is in an unknown state or not
responding.
Out-of-band management (OOBM) port
This RJ-45 port is used to connect a dedicated management network to the switch. To use it, connect an
RJ-45 network cable to the management port to manage the switch through Telnet from a remote PC or a
UNIX workstation.
To use this port, the switch must have an IP address. IP settings can be congured through a console port
connection or automatically from a DHCP/Bootp server.
A networked out-of-band connection through the management port allows you to manage data network
switches from a physically and logically separate management network.
For more information, see the Fundamentals Guide for your switch, found on the Aruba Support Portal.
Back of the switches
Figure 3: Back of 6200F switch
1 2 3 4
Table 5: Back of the 6200F switches LED labels and description
Label Description
1 System fan
2 Integrated power supply fan
3 Ground lug
4 AC power inlet
10 Aruba 6200F Switch Series Installation and Getting Started
Guide

Power connector
The 6200F switches do not have a power switch. They will power on when they are connected to an active AC
power source.
Switch features
The features of the 6200F switches include:
• Combinations of xed 10/100/1000-T and SFP+ ports.
• Power over Ethernet (PoE) operation; enabled by default. The following switches power IP phones,
wireless access points, indoor web cameras, and more.
Aruba 6200F switch PoE per port
Aruba 6200F 24G Class4 PoE 4SFP+ 370W Switch
JL725A
Up to 30W, IEEE 802.3af/at 370W
available PoE power
Aruba 6200F 48G Class4 PoE 4SFP+ 370W Switch
JL727A
Up to 30W, IEEE 802.3af/at 370W
available PoE power
Aruba 6200F 48G Class4 PoE 4SFP+ 740W Switch
JL728A
Up to 30W, IEEE 802.3af/at 740W
available PoE power
For instructions on using the switch PoE features, see the Monitoring Guide for your switch.
• Plug-and-play networking: All ports are enabled by default. Connect the network cables to active network
devices and your switched network is operational.
• Auto MDI/MDI-X on all twisted-pair ports (10/100/1000), meaning that all connections can be made using
straight-through twisted-pair cables.
Cross-over cables are not required, although they will also work. The pin operation of each port is
automatically adjusted for the attached device. If the switch detects that another switch or hub is
connected to the port, it congures the port as MDI. If the switch detects that an end node device is
connected to the port, it congures the port as MDI-X . (See the appendixes for recommended or
required cabling.)
• Automatically negotiated full-duplex operation for the 10/100/1000 RJ-45 ports when connected to other
auto-negotiating devices. The SFP+ ports always operate at full duplex.
• Easy management of the switch through several available interfaces:
◦Console interface: A full-featured, easy-to-use, VT-100 terminal interface for out-of-band or serial
switch management.
◦Web browser interface: An easy-to-use built-in graphical interface that can be accessed from
common web browsers.
◦Bluetooth dongle and Aruba CX Mobile App: A convenient way to manage or congure your switch
using your mobile device.
◦Aruba AirWave: A powerful and easy-to-use network operations system that manages wired and
wireless infrastructures. For more information, visit https://www.arubanetworks.com/products/
networking/management/airwave.
Chapter 2 Introducing the switches 11

◦Aruba Activate: Cloud-based service that provides inventory control and facilitates Zero Touch
Provisioning.
◦Aruba ClearPass Policy Manager: Network policy management software for wired and wireless
network devices that provide on-boarding and role-based control/security.
◦Aruba Central: Network management software cloud platform. It oers IT organizations a simple,
secure, and cost-eective way to manage and monitor Aruba switches and Aruba instant wireless APs.
• Support for the Spanning Tree Protocol to eliminate network loops.
• Support for up to 2048 IEEE 802.1Q-compliant VLANs so you can divide the attached end nodes into
logical groupings that t your business needs.
• Support for many advanced features to enhance network performance: For a description, see the
ArubaOS-CX guides for your switch.
• Ability to update the switch software. To download product updates, go to the Aruba Support Portal.
• An auxiliary port (USB Type-A connector) for updating switch software.
• Switch Hibernation mode to allow the switch to power down for a period each day to save energy.
12 Aruba 6200F Switch Series Installation and Getting Started
Guide

The following sections shows how to install the switch. The switches come with an accessory kit that
includes the brackets for mounting the switch in a standard 19-inch Telco rack or in an equipment cabinet.
Also included are rubber feet that can be attached so the switch can be securely positioned on a horizontal
surface. The brackets are designed to allow mounting the switch in a variety of locations and orientations.
For other mounting options, contact your local Hewlett Packard Enterprise authorized network reseller or
Hewlett Packard Enterprise representative.
Shipping the switch in a rack
If the switch is to be shipped in a rack, it can be mounted and shipped in a Hewlett Packard Enterprise
Universal Rack.
• This method uses the HPE X410 Universal Rack Mounting Kit (J9583A).
• To order the J9583A rack mounting kit, contact your Aruba sales representative.
Included parts
The 6200F switches have the following components shipped with them:
• Documentation kit
• Bluetooth Dongle (5400-3372): Mounting in the USB Type-A AUX for rapid conguration and deployment,
using the Aruba CX Mobile app (found in your phone app store)
• Accessory kit (5300-0103) containing:
◦two mounting brackets
◦eight 8-mm M4 screws to attach the mounting brackets to the switch
◦four 5/8-inch number 12-24 screws to attach the switch to a rack
◦four rubber feet
NOTE: The switch has a USB-C port used to manage the switch. Any compatible USB cable
certied for data transfer can be used as a console cable.
NOTE: J9583A HPE X410 1U Univ 4-post Rack Mount Kit can be ordered separately, or as an
accessory to your switch.
• Power cord, one of the following:
Aruba 6200F PoE Switches
North America 8121-0973 Australia 8121-0857
North America high line 8121-0941 Brazil 8121-1265
Table Continued
Chapter 3
Installing the switch
Chapter 3 Installing the switch 13

Aruba 6200F PoE Switches
South Africa/India 8121-1483 Europe/South Korea 8120-5336
Israel 8121-1009 China 8121-1034
United Kingdom/Hong Kong/
Singapore/Malaysia
8120-5334 Argentina 8121-1481
Switzerland 8120-5339 Chile 8120-8389
Danish 8120-5340 Thailand/Philippines 8121-0671
Japan high line 8120-5338 (JL086A,
JL087A)
Taiwan 15A 8121-1511 (JL086A,
JL087A)
Japan low line 8120-5342 (JL086A) Taiwan 10A 8121-0967 (JL086A)
Aruba 6200F Non-PoE Switches
Argentina 8120-6869 Japan 8120-4753
Australia/New Zealand 8121-0834 Switzerland 8120-6815
Brazil 8121-1069 South Africa 8120-6813
Chile 8120-6980 Taiwan 8121-0974
China 8120-8707 Philippines/Thailand 8121-0668
Continental Europe/South
Korea
8120-6811 UK/Hong Kong/Singapore/
Malaysia
8120-6809
Denmark 8120-6814 US/Canada/Mexico 8121-0973
India 8121-0780 North America high line 8121-0941
Israel 8121-1035
Installation procedures for 6200F switches
Procedure
1. Prepare the installation site.
2. Unpack the switch and verify that you have received the correct parts.
3. Connect power to the switch and wait for the health LED to turn green after the switch passes the self-
test, then remove power from the switch.
4. Mount the switch.
WARNING: Mounting restrictions apply. See the "Warning" under "Installation precautions
and guidelines".
5. Connect the switch to a power source.
14 Aruba 6200F Switch Series Installation and Getting Started
Guide

6. (Optional) Install transceivers.
7. Connect the network cables.
8. Congure the switch for network operation.
Installation precautions and guidelines
To avoid personal injury or product damage when installing your switch, read the following installation
precautions and guidelines.
WARNING:
• Mount devices installed in a rack or cabinet as low as possible. Put the heaviest devices at
the bottom and progressively lighter devices positioned higher.
• To prevent the rack or cabinet from becoming unstable and/or falling over, ensure that it is
adequately secured.
CAUTION:
• If your installation requires a dierent power cord than the one supplied with the switch, be
sure that the cord is adequately sized for the current switch requirements. In addition, be
sure to use a power cord displaying the mark of the safety agency that denes the
regulations for power cords in your country/region. The mark is your assurance that the
power cord can be used safely with the switch.
• Ensure that the power source circuits are properly grounded. Then connect the switch to the
power source by using the power cord supplied with the switch.
• When installing the switch, ensure that the AC outlet is near the switch. Make it easily
accessible in case the switch must be powered o.
• Ensure that the power cord and network cables at the switch mounting location do not
create a tripping hazard.
• Do not install the switch in an environment where the operating ambient temperature
exceeds its specication.
• Ensure that the switch does not overload the power circuits, wiring, and over-current
protection at your installation site. To determine the possibility of overloading the supply
circuits, add the ampere ratings of all devices installed on the same circuit as the switch.
Then compare the total with the rating limit for the circuit. The maximum ampere ratings are
printed on the devices near the AC power connectors.
• Ensure that the air ow around the switch is not restricted. Leave at least 3 inches (7.6 cm)
for cooling.
Prepare the installation site
Cabling Infrastructure: Ensure the cabling infrastructure meets the necessary network specications. See
Cabling and technology information for more information.
Installation Location: Before installing the switch, plan its location and orientation relative to other devices
and equipment:
Chapter 3 Installing the switch 15

• In the front or the back of the switch, leave at least 7.6 cm (3 inches) of space for the twisted-pair and
ber-optic cabling.
• In the back of the switch, leave at least 7.6 cm (3 inches) of space for the power cord.
• On the sides of the switch, leave at least 7.6 cm (3 inches) for cooling, except if the switch is installed in an
open EIA/TIA rack.
Figure 4: Air ow direction of the 6200F switches
Verify that the switch boots correctly
Before installing the switch in its network location, plug it into a power source and verify that it boots
correctly.
Procedure
1. Connect the power cord supplied with the switch to the power connector on the back of the switch. Then
plug the power cord into a properly grounded electrical outlet.
NOTE: The switches do not have a power switch. They are powered on when the power cord
is connected to the switch and to a power source. For safety, locate the power outlet near the
switch installation.
If your installation requires a dierent power cord than the one supplied with the switch, be
sure to use a power cord displaying the mark of the safety agency that denes the
regulations for power cords in your country/region. The mark is your assurance that the
power cord can be used safely with the switch.
2. Check the LEDs on the switch to make sure the switch is on and operating.
When the switch is powered on, it performs its diagnostic self-test and initialization. This boot process,
depending on switch model and conguration, takes approximately 1-2 minutes to complete.
Disconnect power from the switch
Disconnect the power cord from the switch and from the power source.
Mount the switch
After the switch passes self-test, it is ready to be mounted in a stable location. Supported mounting options
for the switches include:
16 Aruba 6200F Switch Series Installation and Getting Started
Guide

• Two-post rack mount
• Tabletop or desktop
• Four-post rack mount (Requires the optional J9583A HPE X410 Universal Rack Mounting Kit.)
WARNING: Do not mount the switch on a wall, under a table, or under another horizontal
surface.
Mounting a switch on a tabletop or desktop
Prerequisites
• Locate the four self-adhesive pads included in the switch accessory kit.
• Select a secure horizontal surface where the network cables and switch power cord will not create a
tripping hazard.
Procedure
1. Attach the four self-adhesive pads to the bottom corners of the switch.
2. Position the switch with the top panel up on the selected horizontal surface.
IMPORTANT: Ensure that the power cord and network cables at switch mounting location
will not create a tripping hazard.
IMPORTANT: Avoid blocking any ventilation openings on the sides, rear, or front of the
switch.
Chapter 3 Installing the switch 17

Mounting the switch in a two-post rack
Prerequisites
Before beginning here:
Prepare your network data cables (not included) for connecting the switch to the network.
Procedure
1. Attach the rack mount brackets to the switch by using a #1 Phillips (cross-head) screwdriver and the
supplied eight 8-mm M4 screws.
1
2
12
2. Use the four number 12-24 screws to secure the brackets to the rack.
Mounting the switch in a four-post rack
The four-post rack mount for the switches requires the optional J9583A HPE X410 Universal Rack Mounting
Kit. To use this kit to mount a switch, see the installation instructions provided in that kit.
Connect the switch to a power source
Procedure
1. Plug the included power cord into the power connector on the switch and into a nearby AC power source.
2. Recheck the LEDs during self-test.
18 Aruba 6200F Switch Series Installation and Getting Started
Guide

(Optional) Install transceivers
You can install or remove transceivers from the slots on the front of the switch without having to power o
the switch.
NOTE:
• The transceivers operate only at full duplex. Half duplex operation is not supported.
• Ensure that the network cable is NOT connected when you install or remove a transceiver.
(Optional) Insert up to four SFP or SFP+ transceivers in the xed transceiver slots on the switch front panel.
Connect network cables
Connect network cables from network devices or your patch panels to the xed RJ-45 ports and to any
installed transceivers.
Connect network cables to the RJ-45 data ports and to any optional transceivers installed on the switch front
panel.
Chapter 3 Installing the switch 19

SFP+ installation notes
IMPORTANT: When selecting a ber SFP+ device, make sure it can function at a maximum
temperature that is not less than the recommended maximum operational temperature of the
product. Use only an approved Laser Class 1 SFP+ transceiver.
IMPORTANT: To ensure proper operation of your switch, use only the Aruba SFP+ transceivers
supported by your switch.
Non-Aruba SFP+ transceivers are not supported. Use of supported Aruba products ensures that
your network maintains optimal performance and reliability. If you require additional
transceivers, contact an Aruba sales representative or an authorized reseller. The following
resources can help you to nd transceiver support information for your switch model:
• See the Transceiver Guide.
• See the supported transceivers information in the data sheet for your switch model.
Hot swapping SFP+ transceivers
Supported SFP+ transceivers that you can install in your Aruba switch can be “hot swapped”– removed and
installed while the switch is receiving power. However, disconnect the network cables from the SFP+
transceivers before hot-swapping them.
When you replace a SFP+ transceiver with another transceiver of a dierent type, the switch may retain
selected port-specic conguration settings that were congured for the replaced unit. Be sure to validate or
recongure port settings as required.
SFP+ connections to devices with xed speed/duplex congurations
When connecting a device to your switch port that contains a SFP+ transceiver, the speed and duplex
settings of the switch port and the connected device must match. Otherwise, the device may not link
properly—you may not get a link. For some older network devices, the default speed/duplex settings may be
predened such that they are set dierently from the default conguration of your switch. (For example,
1000 Mbps/Full Duplex.) These setting dierences may also apply to some older Hewlett Packard Enterprise
devices. Because of these default speed/duplex considerations, make sure that devices connected to your
SFP+ ports are properly congured. At a minimum, make sure the congurations match.
20 Aruba 6200F Switch Series Installation and Getting Started
Guide