Hewlett Packard Enterprise B Series Programming manual

HPE B-series 16Gb FC
Switches Quick Start
Instructions
©Copyright 2014, 2016 Hewlett Packard Enterprise Development LP
*5900-4827*
Part Number: 5900-4827
Published: January 2016
Edition: 4
Overview
Read these instructions to set up and configure the
HPE StoreFabric SN6500B 16Gb 96-port FC
Switch, HPE SN6000B 16Gb 48-port FC Switch
and HPE SN3000B 16Gb 24-port FC Switch.
These instructions provide basic configuration
steps. For detailed rack mount and configuration
instructions, download the HPE B-series 16Gb
Switches Hardware reference guide from the
storage section of the Hewlett Packard Enterprise
website: http://www.hpe.com/support/manuals.
Figure 1 (page 1) shows the port side of the
96-port switch.
Figure 1 Port side of the 96-port switch
2. System status LED1. System power LED
4. FC ports 0–7 (all LEDs
above)
3. USB port
6. FC ports 48–955. FC ports 8–47
8. Management Ethernet port
with LED
7. Switch ID pull-out tab
9. Serial console port
Verify the SN6500B 16Gb 96–port FC switch
carton contents
Verify that the carton contains the following (any
SFPs ordered will not be in this carton; they will be
packaged separately):
•One HPE SN6500B 16Gb 96–port FC Switch
with two power supplies and three fan
assemblies
•Rubber feet, required to set up the switch as
a standalone unit.
•Serial cable with an RJ-45 connector.
•HPE SAN Network Advisor DVD.
•Brocade EZ Switch and China ROHS
documentation.

•One accessory kit with the following items:
Rack Mount Kit, including rails and rail
mounting hardware.
◦
◦Hewlett Packard Enterprise product
documentation, including Read Me First,
Safety Guides, End User License
Agreement and Warranty.
•Two power cords.
SN6000B 16Gb 48-port FC switch
Figure 2 (page 2) shows the port side of the
48-port switch.
Figure 2 Port side of the 48-port FC Switch
2. Management Ethernet port
with LEDs
1. System status LED
4. FC ports (0-3)3. USB port
6. FC ports (44-47)5. FC ports (40-43)
8. Switch ID pull-out tab7. FC ports (4-7)
10. System power LED9. Serial console port
Verify the 16Gb 48-port FC switch carton
contents
Verify that the carton contains the following (any
SFPs ordered will not be in this carton; they will be
packaged separately):
•One SN6000B 16Gb 48-port FC Switch with
two integrated power supply/fan assemblies
•Rubber feet, required to set up the switch as
a standalone unit
•Serial cable with an RJ-45 connector plus an
adaptor for RJ-45 to DB9
•SAN Network Advisor DVD
•Brocade EZ Switch and China ROHS
documentation
•One accessory kit with the following items:
Rack Mount Kit, including rails, rail
mounting hardware, and plenum
◦
◦Hewlett Packard Enterprise product
documentation, including Read Me First,
Safety Guides, End User License
Agreement and Warranty
•Two power cords
SN3000B 16Gb 24-port FC switch
Figure 3 (page 2) shows the port side of the
24-port switch.
Figure 3 Port side of the 24-port switch
2. Management Ethernet port
with LEDs
1. System status LED
4. FC ports (0-3)3. USB port
6. Serial console port5. System power LED
8. FC ports (4–7)7. Switch ID pull-out tab
Verify the SN3000B 16Gb 24-port FC
switch carton contents
Verify that the carton contains the following (any
SFPs ordered will not be in this carton; they will be
packaged separately):
•One SN3000B 16Gb 24-port FC Switch with
one integrated power supply/fan assembly
•Rubber feet, required to set up the switch as
a standalone unit
•Serial cable with an RJ-45 connector plus an
adaptor for RJ-45 to DB9
•SAN Network Advisor DVD
•Brocade EZ Switch and China ROHS
documentation
•One accessory kit with the following items:
Rack Mount Kit, including rails, rail
mounting hardware, and plenum
◦
◦Hewlett Packard Enterprise product
documentation, including Read Me First,

Safety Guides, End User License
Agreement and Warranty
•One power cord
NOTE: The HPE SN3000B 16Gb Fibre
Channel Switch can, as an option, be
configured with a second power supply/fan
assembly, which must be ordered separately.
Verify the 16Gb FC Switch installation
requirements
To set up the switch for the first time, you will need
the following:
•Workstation with an installed terminal emulator
(such as HyperTerminal)
•Unused IP address and corresponding subnet
mask and gateway address
•Serial cable (supplied with the switch)
•Ethernet cable
•Access to an FTP server, SCP server, or USB
device for backing up the switch configuration
(optional)
•HPE B-series SFP+ transceivers and
compatible cables (HPE B-series 16 Gb/s
SFP+ transceivers required for 16 Gb/s
performance), as required
IMPORTANT: Order transceivers or cables
separately. The StoreFabric SN6500B 16Gb
96-port FC Switch, SN6000B, and SN3000B
16Gb FC Switches support only transceivers
labeled B-series SFP+. See the compatibility
matrix at http://www.hpe.com/support/
SANcompatibility for more information on
supported transceivers.
Plan the 16Gb FC Switch site
environment
To ensure adequate cooling, install the switch with
the non-port side (which contains the air intake
vents) facing the cool-air aisle. Verify that the
ambient air temperature does not exceed 40°C
(104°F) and that the ambient humidity remains
between 10% and 85% while the switch is
operating.
NOTE:
•For switches with Port Side Air Intake,
install the switch with the port side facing
the cool-air aisle.
•For the SN6000B and SN3000B, you
must install the plenum if the switch is
to be installed in a rack.
To install and operate the switch successfully,
ensure that:
•For the SN6500B 16Gb FC Switch, the primary
AC input is 90–264 VAC, Nominal: 100–240
VAC, 12.0A–5.0A; 47–63 Hz. The switch
auto-senses input voltage.
•For the SN6000B and SN3000B 16Gb
switches, the primary AC input is 85–264 VAC,
Nominal: 100–240 VAC, 2.0 A; 47–63 Hz. The
switch auto-senses input voltage.
•The primary outlet is wired correctly, protected
by a circuit breaker, and grounded in
accordance with local electrical codes.
•The supply circuit, line fusing, and wire size
are adequate, as specified by the electrical
rating on the switch nameplate.
For additional power supply information, see the
B-series 16Gb Switches Hardware Reference
Guide.

Install the SN6000B Switch and
SN3000B Switch in a rack using the
Rack Mount Kit
You can use the Switch Rack Mount Kits to install
your 16Gb FC Switch in an HPE 10000 Series
Rack.
CAUTION: Install the Rack Mount Kit so
that when the switch is installed, the port side
faces the rear of the rack. This configuration
optimizes performance by:
•Providing better airflow by using a
plenum to force cool air to enter the
switch from the front of the rack
•Providing room for a gradual bend in the
fiber optic cables because the port side
of the switch is set back from the edge
of the rack
Use only the screws provided in the Rack
Mount Kit. Using other screws can cause
damage to internal components.
NOTE: For switches with Port Side Air
Intake, install the Rack Mount Kit so that
when the switch is installed the port side
faces the front of the rack.
To install the switch in a rack using the Rack Mount
Kit:
1. Place the switch on a flat surface and attach
each inner rail to the switch using three
flat-head screws as shown in Figure 4 (page
4).
The rails are labeled Left and Right to
designate the left side and right side of the
switch as viewed from its non-port side.
Figure 4 Attaching the inner rails to the
switch
2. Choose a rack mounting location that provides
clearance for the switch power cords to run
between the rack sides and the rails at the front
of the rack.
3. Attach each rear mounting bracket to a rear
rack upright column using two Phillips screws
and adapter washers. See Figure 5 (page 4).
NOTE: For switches with Port Side Air
Intake, attach the rear mounting brackets
to the front rack upright column.
Figure 5 Installing the rear mounting
brackets

4. Attach each outer rail as shown in
Figure 6 (page 5).
The rails are labeled Left and Right to
designate the left side and right side of the rack
as viewed from the front of the cabinet.
NOTE: For switches with Port Side Air
Intake, attach Left outer rail to the right
side of the rack and Right outer rail to
the left side of the rack.
Figure 6 Attaching the outer rails
a. Slide the rail over the rear mounting
bracket.
b. Attach the front of the rail to a front rack
upright column using two Phillips screws
and adapter washers.
c. Attach the outer rail to the rear mounting
brackets using a Phillips screw.
TIP: Tighten the rear screws just
enough for the end of the screw to
go through the rear bracket. Later
in the procedure, you will need room
to slide the inner rail between the
screw head and the outer bracket.
5. From the front of the rack, slide the switch (with
inner rails attached) onto the outer rails, taking
care to align the inner rails with the attachment
screws on the outer rails at the rear of the rack.
See Figure 7 (page 5).
Figure 7 Installing the switch in the rack
6. When the switch is in place, secure the inner
rails to the outer rails by tightening the screws
at the rear of the rack.
7. At the front of the rack, run the switch power
cords from the sides of the rack through the
cutouts in the rail, and then connect them to
the switch power supplies. Connect two power
cords to the 48-port switch and the 96-port
switch. Connect one power cord to the 24-port
switch. See Figure 8 (page 5).
IMPORTANT: Make sure that the
power cords do not come in contact with
any sharp edges.
NOTE:
•For switches with Port Side Air
Intake, the power connections are
at the rear of the rack.
•If you are configuring the second
(optional) power supply, the 24-port
switch will also have two power
cords.
Figure 8 Connecting power and installing
the plenum
3. Power switches1. Cutouts for power cords
4. Plenum thumb screws2. Power cable plugs
8. Connect the other end of the power cords to
power sources on separate circuits to protect
against AC failure. (Make sure that two power
cords are connected to the 48-port switch and
one power cord is connected to the 24–poort
switch.)
NOTE: If you are configuring the
second (optional) power supply, the
24-port switch will also have two power
cords.

9. Power on the power supplies by setting the
power switches to the ON position (|).
The power supply LEDs are amber until the
Power On Self Test (POST) is complete, and
then change to green. The SN6000B 16Gb FC
Switch takes several minutes to boot and
complete POST.
NOTE: When installed, the plenum
covers the power supply switches and
LEDs. However, the LEDs are visible
through the air holes in the front of the
plenum.
10. Slide the plenum over the non-port side of the
inner rails, taking care to bypass the power
cables. See Figure 8 (page 5).
11. Tighten the thumbscrews to secure the plenum
to the front of the rack.
12. Proceed to “Switch setup ” (page 10).
Installing the SN6500B Switch in a rack
using the Rack Mount Kit
Use the SAN Switch Rack Mount Kit to install your
Hewlett Packard Enterprise device in the following
Hewlett Packard Enterprise custom racks:
•HPE System/e Rack
•10000 Series Rack
For optimal cable management, Hewlett Packard
Enterprise recommends that you install the SAN
Switch Rack Mount Kit to allow the nonport side of
the device to slide out of the cool-air side of the
rack. In this installation, the port side of the device
is set back from the edge of the rack, allowing a
more gradual bend in the fiber optic cables.
The following items are required to install the device
in a rack:
•Power cables
•#2 Phillips screwdriver
•7/16-inch wrench or socket
•SAN Switch Rack Mount Kit hardware
Table 1 (page 6) identifies the rails and
rail-mounting hardware.
Table 1 SAN Switch Rack Mount Kit hardware
DescriptionItem
Two rear mounting brackets
A right inner rail and a right outer
rail
A left inner rail and a left outer rail
14 #8-32 x 5/16-inch Phillips
panhead SEMS screws for use with
the SN6500B Switch. This device
requires 10 screws
14 #8-32 x 3/16-inch Phillips
panhead screws with thread lock
(do not use)
Ten #10-32 x 1/2-inch Phillips
panhead screws with captive star
lock washers
Eight #10 alignment washers
Eight #10 adapter washers
Two 1/4-20 hex nuts with captive
star lock washers
Two 1/4-inch flat washers
CAUTION: For proper air flow, the SFP+
media side of the device port side must face
the rear of the rack. This allows cool air to
enter the front of the rack and exit from the
rear.
For switches with Port Side Air Intake, the
SFP+ media side of the device port side must
face the front of the rack.
To install the device in a rack:
1. Verify that the required parts and hardware are
available (see Table 1 (page 6)).
2. Choose a mounting location for the device in
the rack.

3. Attach the rear mounting brackets to the rear
rack uprights.
NOTE: For switches with Port Side Air
Intake, attach the rear mounting brackets
to the front rack uprights.
•For 10000 series rack, assemble each of
the brackets using two #10-32 x 1/2-inch
Phillips panhead screws with captive star
lock washers and two #10 adapter
washers, as shown in Figure 9 (page 7).
•For System/e Rack, install the two rear
mounting brackets using 8-32 x 5/16-inch
Phillips panhead SEMS screws and two
#10 alignment washers, as shown in
Figure 10 (page 7).
Figure 9 Installing the rear mounting
brackets (HPE 10000 Series Rack)
Figure 10 Installing the rear mounting
brackets (HPE System/e Rack)
NOTE: The SAN Switch Rack Mount
Kit contains rails labeled Left and Right
to designate the left side and right side
of the device or cabinet as viewed from
the front of the cabinet.

4. Assemble the outer rails as follows:
NOTE: For switches with Port Side Air
Intake, attach Left outer rail to the right
side of the rack and Right outer rail to
the left side of the rack.
a. Attach the left outer rail and right outer rail
to the rear mounting brackets using two
1/4-20 hex with captive star lock washers
attached loosely as shown in
Figure 11 (page 8). Do not tighten the
nuts.
Figure 11 Installing the outer rails (HPE
10000 Series Rack)
b. Depending on the rack you are using,
complete one of the following tasks:
•For 10000 Series Rack, install two
#10-32 x 1/2-inch Phillips panhead
screws with captive star lock washers
and two #10 adapter washers in the
upper and lower holes on the right
rail. Then install two #10-32 x 1/2-inch
Phillips panhead screws with captive
star lock washers and two #10
adapter washers in the upper and
lower holes on the left rail (see
Figure 12 (page 8)).
Figure 12 Assembling the outer
rails (HPE 10000 Series Rack)
•For System/e Rack, install two #10-32
x 1/2-inch Phillips panhead screws
with captive star lock washers and
two #10 alignment washers in the
upper and lower holes on the right
rail. Then install two #10-32 x 1/2-inch
panhead screws with captive star lock
washers and two #10 alignment
washers in the upper and lower holes
on the left rail (see Figure 13 (page
8)).
Figure 13 Assembling the outer
rails (HPE System/e Rack)
5. Use the screw type #8-32 x 5/16-inch (in the
screw holes marked 16) to attach the two inner
rails to the switch. Five screws are required for
each rail.
Figure 14 (page 9) shows how the inner rails are
attached to the switch with the open ends
(highlighted in yellow) on the port side.
NOTE: The switch in the figure is not a
SN6500B, but it shows the direction of the
open ends of the rails when they are attached
to the switch.

Figure 14 Inner rails attachment
Securing the device to the outer rails
1. Insert the device with the attached inner rails
to the outer rails.
2. Insert the device into the rack and install one
#10-32 x 1/2-inch Phillips panhead screw with
captive star lock washer. Repeat for the other
side. See Figure 15 (page 9) and
Figure 16 (page 9).
Figure 15 Securing the device (HPE 10000
Series Rack)
Figure 16 Securing the device (HPE
System/e Rack)
3. Tighten the hex nuts installed in Step 4.
This completes the rack mount procedure.
Install a standalone switch
1. Unpack the switch and verify the contents as
described in “Verify the SN6500B 16Gb
96–port FC switch carton contents” (page 1).
2. Apply the adhesive rubber feet to prevent the
switch from sliding off the supporting surface.
a. Clean the indentations at each corner on
the bottom of the switch to ensure that
they are free of dust or other debris.
b. With the adhesive side against the
chassis, place one rubber foot in each
indentation and press into place.
3. Place the switch on a flat, sturdy surface.
Power on the switch
1. Connect a power cord to each power supply
present:
•For the 96-port switch and the 48-port
switch, connect the power cords to both
power supplies and then to power sources
on separate circuits to protect against AC
failure.
•For the 24-port switch, connect a power
cord to either the single power supply
present or to both power supplies, if an
optional second power supply is present.
Then connect the power cords to power
sources on separate circuits to protect
against AC failure.
Ensure that the cords have a minimum service
loop of 6 inches available and are routed to
avoid stress.
NOTE: If you are configuring the
second (optional) power supply, the
24-port switch will also have two power
cords.
2. Power on the power supplies by setting the AC
switches to the on position (|).
The power supply LEDs are amber until POST
is complete, and then change to green. The
switch takes several minutes to boot and
complete POST.

NOTE: Power is supplied to the switch
as soon as the first power supply is
connected and turned on.
3. After POST is complete, verify that the switch
power and status LEDs on the port side of the
switch are green.
Switch setup
To set up the switch, you will need the following:
•Standard screwdriver
•If you are using static IP addressing, you will
need the following items (not required if you
are using Dynamic Host Configuration Protocol
(DHCP)):
◦Fixed IP address (IPv4 or IPv6) for the
switch
◦Subnet mask value
◦Default gateway value
•World Wide Name (WWN), located on the
switch ID pull-out tab
•Ethernet connection (hub or switch)
•Ethernet and Fibre Channel cables
•Disk array with Fibre Channel ports
•Browser that allows pop-up windows
Connect the serial cable
1. Connect the serial cable to the serial port on
the switch and to an RS-232 serial port on the
workstation.
If the serial port is RJ-45 instead of RS-232,
remove the adapter on the end of the serial
cable and insert the exposed RJ-45 connector
into the RJ-45 serial port on the workstation.
2. Disable any serial communication programs
running on the workstation.
3. Open a terminal emulator (such as
HyperTerminal on a PC, or TERM, TIP, or
Kermit in a UNIX environment) and configure
the application as follows:
For most Windows systems:
Bits per second: 9,600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
For most UNIX systems:
tip /dev/ttyb -9600
If ttyb is already in use, try ttya instead:
tip /dev/ttya -9600
Log in to the serial console port
1. Verify that the switch has completed POST.
When POST is complete, the port status,
switch power, and status LEDs return to a
normal state.
2. When the terminal emulator stops reporting
information, press Enter to display the login
prompt.
3. Log in to the switch as admin, using the default
password, password.
You are prompted to change the default
password at initial login.
NOTE: You can configure the switch using
a static IP address or DHCP. With DHCP
(enabled by default), the switch obtains its IP
address, subnet mask, and default gateway
address from the DHCP server. The DHCP
client can connect only to a DHCP server that
is on the same subnet as the switch. The
Ethernet cable must be connected to the
management Ethernet port on the switch if
you are using DHCP. If you are using a static
IP address, see “Set a static IP address”
(page 11).

Set a static IP address
1. Use the ipaddrset command to set the
Ethernet IP address.
•For an IPv4 address, use dotted-decimal
notation:
Ethernet IP Address:
192.168.74.102
•For an IPv6 address, use colon-separated
notation:
switch:admin> ipaddrset -ipv6
--add 1080::8:800:200C:417A/64
The following message confirms the change:
IP address is being changed...Done.
2. Provide the remaining network information:
Ethernet IP Address: 192.168.74.102 Ethernet
Subnet mask: 255.255.252.0 Gateway IP
Address: 15.226.172.1
3. As an option, verify the IP address by entering
the ipaddrshow command at the prompt.
4. Record the IP address on the pull-out tab on
the port side of the switch.
5. When prompted, enter off to disable DHCP:
DHCP [OFF]: off
6. If the serial port is no longer required, use the
logout command to log out of the serial
console. Remove the serial cable and replace
the plug in the serial port.
7. Connect the Ethernet port on the switch to the
Ethernet network that assigned the IP address.
Set the date and time
The date and time settings are used for logging,
error detection, and troubleshooting.
1. Using a Telnet or Secure Shell (SSH) session,
connect to the switch using the IP address that
you configured, and then log in to the switch
as admin using the password you set when
you logged in to the serial console port.
2. Enter the date command using the following
syntax:
date "mmddHHMMyy", where:
mm is the month; valid values are 01 through
12.
dd is the date; valid values are 01 through 31.
HH is the hour; valid values are 00 through 23.
MM is minutes; valid values are 00 through 59.
yy is the year; valid values are 00 through 99.
NOTE: Values greater than 69 are
interpreted as 1970 through 1999; values
less than 70 are interpreted as 2000
through 2069.
3. Enter the tstimezone command:
switch:admin> tstimezone
[--interactive]/ [, timezone_fmt]
Use timezone_fmt to set the time zone by
country/city or by time-zone ID, such as PST.
The following example shows how to change
the time zone to US/Central:
switch:admin> tstimezoneTime Zone
: US/Pacificswitch:admin>
tstimezone US/Centralswitch:admin>
tstimezoneTime Zone : US/Central
4. Enter the tsclockserver command to
synchronize local time using NTP:
switch:admin> tsclockserver
“<ntp1;ntp2>”
The value of ntp1 is the IP address or DNS
name of the first NTP server, which the switch
must be able to access. The value of ntp2 is
the second NTP server and is optional. When
multiple NTP server addresses are specified,
tsclockserver sets the first obtainable
address as the active NTP server. The default
value is LOCL.
switch:admin> tsclockserver
LOCL
switch:admin> tsclockserver "132.163.135.131"
switch:admin> tsclockserver
132.163.135.131
switch:admin>
Configure the zones, and perform device
selection
See the Brocade Network Advisor User Manual,
available from the storage section of the Hewlett
Packard Enterprise website: http://www.hpe.com/
support/manuals.
Connect devices
The Connect Devices window shows a graphical
representation of the switch with the device
connections, based on the information that you
entered in “Configure the zones, and perform device
selection” (page 11).
NOTE: Only B-series optical transceivers
are supported. See http://www.hpe.com/
support/SANcompatibility for more
information.

To connect devices:
Transceivers and cables are keyed so that they can
be inserted only one way. If a transceiver or cable
does not slide in easily, make sure it is oriented
correctly.
Do not insert a cable intended for an mSFP
transceiver into a regular SFP+ transceiver; you
may damage the cable. The mSFP transceivers
and cables are supported only with the 64-port
8Gb/s blade for the SN8000B SAN directors. Do
not force a standard SFP cable into an mSFP
transceiver; you may damage the transceiver.
1. Install the SFP+ transceivers in the Fibre
Channel ports on the switch to match the ports
shown on the screen (see Figure 17 (page
12)). If you are using an SFP+ transceiver that
does not have a pull tab, ensure that the wire
bail is in the unlocked position.
Figure 17 Inserting an SFP+ transceiver with
no pull tab in a Fibre Channel port
Figure 18 Inserting a 16 Gb/s SFP+
transceiver in a Fibre Channel port
a. Remove any protector plugs from the
SFP+ transceiver. Insert each SFP+
transceiver (right side up in the top row of
ports, and upside down in the bottom row
of ports) until it is firmly seated and the
latching mechanism clicks.
The 16 Gb/s SFP+ transceivers do not
have bails. Use the pull tab on the 16 Gb/s
SFP+ transceiver to push the transceiver
into the port.
b. Close the latching bail on the non-16 Gb/s
SFP+ transceiver.

2. Connect the Fibre Channel cables from the
switch to your host and storage devices.
Ensure that the physical connections match
the connections on the Device Connection
screen.
a. Remove the plastic protector caps from
the Fibre Channel cable ends (if there are
any), and position the cable connector so
that it is oriented correctly.
b. Position a cable so that the key (the ridge
on one side of the cable connector) is
aligned with the slot in the transceiver (see
Figure 18 (page 12)).
c. Insert the cable into the transceiver until
the latching mechanism clicks.
d. The Device Connection screen shows
missing, valid, and invalid connections as
you cable the switch. It can take up to 15
seconds for the screen to display the
connection as valid. Verify that the
connections display green and then click
Next.
Verify switch operation
1. Check the LEDs to verify that all components
are functional. For information about LED
patterns, see the B-series 16Gb Switches
Hardware Reference Guide.
2. Verify the correct operation of the switch by
issuing the switchShow command.
This command provides information about
switch and port status.
3. Verify the correct operation of the fabric by
issuing the fabricShow command.
This command provides general information
about the fabric.
4. Back up the switch configuration to an FTP
server by issuing the configUpload
command and following the prompts.
This command uploads the switch configuration
to the server, making it available for
downloading to a replacement switch if
necessary.
Set switch features
This completes the initial setup of your SN6500B,
SN6000B, or SN3000B 16Gb FC Switch. See the
Fabric OS 7.0.x Administrator's Guide and the
Fabric OS 7.0.x Command Reference Manual for
detailed instructions on setting all supported switch
features.
Documentation feedback
Hewlett Packard Enterprise is committed to
providing documentation that meets your needs.
To help us improve the documentation, send any
errors, suggestions, or comments to Documentation
Feedback ([email protected]). When
submitting your feedback, include the document
title, part number, edition, and publication date
located on the front cover of the document. For
online help content, include the product name,
product version, help edition, and publication date
located on the legal notices page.