Hewlett Packard Enterprise HPE OfficeConnect 1405 v3 Switch Series User manual

HPE OfficeConnect 1405 v3 Switch Series
Getting Started Guide
Part number: 5200-0804
Document version: 5W100-20160622

© Copyright 2016 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard
Enterprise products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett
Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or
copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software
Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s
standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard
Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise
website.
Acknowledgments
Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the
United States and other countries.
Microsoft® and Windows® are trademarks of the Microsoft group of companies.
Adobe® andAcrobat® are trademarks of Adobe Systems Incorporated.
Java and Oracle are registered trademarks of Oracle and/or its affiliates.
UNIX® is a registered trademark of The Open Group.

i
Contents
Preparing for installation ················································································· 1
Safety recommendations ···································································································································1
Examining the installation site····························································································································1
Temperature/humidity ································································································································2
Cleanliness·················································································································································2
EMI·····························································································································································2
Installing the switch························································································· 3
Horizontal surface mounting ······························································································································3
Wall mounting ····················································································································································3
Under-table mounting ········································································································································5
Connecting cables ·············································································································································6
Connecting network cable··························································································································6
Connecting the power adapter ···················································································································6
Verifying the installation ·····································································································································7
Document conventions and icons ··································································· 8
Conventions ·······················································································································································8
Network topology icons······································································································································9
Support and other resources ········································································ 10
Accessing Hewlett Packard Enterprise Support ······························································································10
Accessing updates···········································································································································10
Websites ··················································································································································11
Customer self repair·································································································································11
Remote support········································································································································11
Documentation feedback ·························································································································12
Appendix A Chassis views and technical specifications ······························· 13
Chassis views ··················································································································································13
HPE 1405 5G ···········································································································································13
HPE 1405 8G ···········································································································································14
Technical specifications ···································································································································14
Chassis dimensions and weights ·············································································································14
Ports and interface card slots···················································································································14
Environmental specifications ···························································································································15
Power specifications ········································································································································15
DC input voltage specifications ················································································································15
Power consumption specifications ···········································································································15
Appendix B LEDs·························································································· 16
Power LED ···············································································································································16
Copper port LEDs ····································································································································16
Appendix C Troubleshooting········································································· 17

1
Preparing for installation
The HPE OfficeConnect 1405 v3 Switch Series includes models listed in Table 1.
Table 1 HPE OfficeConnect 1405 v3 Switch Series models
Product
code HPE description Alias RMN
JH407A HPE OfficeConnect 1405 5G v3 Switch HPE 1405 5G v3 Switch HNGZA-HA0030
JH408A HPE OfficeConnect 1405 8G v3 Switch HPE 1405 8G v3 Switch HNGZA-HA0031
IMPORTANT:
For regulatory identification purposes, the switches are assigned Regulatory Model Numbers
(RMNs). The RMNs should not be confused with the marketing name HPE 1405, or the product
codes.
Safety recommendations
To avoid any equipment damage or bodily injury, read the following safety recommendations before
installation. The recommendations do not cover every possible hazardous condition.
•To avoid damage to the electrolytic capacitor in the switch, do not store the switch without
power for more than one year.
•Before cleaning the switch, remove all power adapters from the switch. Do not clean the switch
with a wet cloth or liquid.
•Do not place the switch near water or in a damp environment. Prevent water or moisture from
entering the switch chassis.
•Do not place the switch on an unstable case or desk. The switch might be severely damaged in
case of a fall.
•Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the
switch free of obstruction.
•Make sure the operating voltage is in the required range.
•To avoid electrical shocks, do not open the chassis while the switch is operating or when the
switch is just powered off.
•The accessories shipped with the switch, including but not limited to power adapter, are
intended only for the switch. Please do not use them for other products.
Examining the installation site
The switches must be used indoors. You can mount your switch on a horizontal surface, on a wall, or
under a table. Make sure the following requirements are met:
•A minimum of 5 cm (1.97 in) of clearance is reserved at the air inlet and outlet vents for
ventilation.
•The air inlet and outlet vents are not blocked when the switch is mounted under a table or on a
horizontal surface.
•The table, or horizontal surface is sturdy enough to support the switch and its accessories.
To ensure correct operation and long service life of your switch, install it in an environment that meets
the requirements described in the following subsections.

2
Temperature/humidity
Maintain temperature and humidity in the equipment room as described in "Environmental
specifications."
•Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical
property change of materials, and metal corrosion.
•Lasting low relative humidity can cause washer contraction and ESD and cause problems
including loose mounting screws and circuit failure.
•High temperature can accelerate the aging of insulation materials and significantly lower the
reliability and lifespan of the switch.
Cleanliness
Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of
metal components and contact points, especially when indoor relative humidity is low. In the worst
case, electrostatic adsorption can cause communication failure.
Table 2 Dust concentration limit in the equipment room
Substance Concentration limit (particles/m³)
Dust ≤3 x 104 (no visible dust on the tabletop over three days)
NOTE:
Dust diameter ≥5 μm
The equipment room must also meet strict limits on salts, acids, and sulfides to eliminate corrosion
and premature aging of components, as shown in Tabl e 3.
Table 3 Harmful gas limits in the equipment room
Gas Maximum concentration (mg/m3)
SO20.2
H2S 0.006
NH30.05
Cl20.01
EMI
All electromagnetic interference (EMI) sources, from outside or inside of the switch and application
system, adversely affect the switch in the following ways:
•A conduction pattern of capacitance coupling.
•Inductance coupling.
•Electromagnetic wave radiation.
•Common impedance coupling.
To prevent EMI, perform the following tasks:
•Keep the switch far away from radio transmitting stations, radar stations, and high-frequency
devices.
•Use electromagnetic shielding, for example, shielded interface cables, when necessary.

3
Installing the switch
WARNING!
Before installing or moving the switch, remove the power adapter.
You can install the switch on a horizontal surface, on a wall, or under a table. The procedures for
installing the HPE 1405 5G v3 Switch and the HPE 1405 8G v3 Switch are the same. This section
uses the HPE 1405 5G v3 Switch as an example.
Horizontal surface mounting
IMPORTANT:
•Reserve a clearance of 10 cm (3.9 in) around the chassis for heat dissipation.
•Do not place heavy objects on the switch.
To mount the switch on a horizontal surface:
1. Verify that the horizontal surface is sturdy.
2. Place the switch upside up on the horizontal surface.
Wall mounting
The HPE 1405 5G v3 Switch and HPE 1405 8G v3 Switch can be installed on a wall. The type of
screws used to mount the switch on the wall depends on the wall type. This section uses a concrete
wall as an example.
The screws must be a minimum of 3 mm (0.12 in) and a maximum of 3.8 mm (0.15 in) in diameter.
The screw head must be a minimum of 6 mm (0.24 in) and a maximum of 9.8 mm (0.59 in) in
diameter.
Figure 1 Wall-mounting anchor kit
To install the switch on a concrete wall:
1. Drill two holes at the same height, as shown in Figure 2.

4
Figure 2 Hole spacing
The hole depth and diameter depend on the wall anchors and screws you use. Make sure you can
push the anchors to their full depth in the holes.
Installation hole spacing varies by switch model, as shown in Tab le 4.
Table 4 Installation hole spacing requirements
Product Installation hole spacing
HPE 1405 5G 74 mm (2.91 in)
HPE 1405 8G 102 mm (4.02 in)
2. Insert one wall anchor into each hole until the anchors are flush with the wall surface.
3. Drive one screw into each wall anchor, and tighten the screws just enough to keep it secure in
the wall anchor.
Leave a minimum clearance of 1.5 mm (0.06 in) between the base of the screw head and the
wall anchor so the switch can hang on the screws securely.
Figure 3 Driving a screw into a wall anchor
4. Align the two mounting holes in the switch chassis bottom with the two screws on the wall and
hang the switch.
Make sure the Ethernet ports are facing upwards or downwards and the chassis side panels are
perpendicular to the ground.

5
Figure 4 Wall mounting
(1) Mounting hole in the switch chassis bottom
Under-table mounting
CAUTION:
•A network-attached switch with cables mounted upside down can be heavy. Verify that the table
is sufficiently strong and of a material that can support the screws that hold the weight of the
switch and the attached cables. Make sure the cables are protected and out of the way.
•Regularly inspect the installation of the switch to ensure that the switch remains securely
anchored and unobstructed.
The HPE 1405 5G v3 Switch and HPE 1405 8G v3 Switch support under-table mounting. The wall
mounting screws (provided) can be used when you mount the switch under a table.
Figure 5 Under-table mounting
To mount the switch under a table:
1. Follow the instructions on wall mounting to determine the location of screw holes to be used for
under-table mounting.
2. Align the two mounting holes in the switch chassis bottom with the two screws on the bottom of
the table and hang the switch.
3. Use a third screw to prevent switch movement.
Mounting slots
74 mm2.91 in
Wood table
Third securing screw

6
NOTE:
Installation hole spacing varies by switch model. For more information, see Table 4.
Connecting cables
Connecting network cable
Use crossover cable or straight through cable to connect a PC or other network devices to the
Ethernet port of the switch.
Figure 6 Connecting network cable
Connecting the power adapter
The HPE 1405 5G v3 Switch and HPE 1405 8G v3 Switch support a power adapter.
To connect the power adapter:
1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.
2. Make sure the correct power source is used.
3. Connect one end of the power adapter to the DC power receptacle on the switch.
4. Connect the other end of the power adapter to the AC power supply.
5. Examine the power LED. If it is ON, the power connection is correct.
Figure 7 Connecting the power adapter

7
Verifying the installation
After you complete the installation, verify the following items:
•There is enough space for heat dissipation around the switch.
•The table, or horizontal surface is stable.
•The correct power source is used.
•The power adapter are correctly connected.
•All the interface cables are cabled indoors. If any cable is routed outdoors, verify that the socket
strip with lightning protection and lightning arresters for network ports have been correctly
connected.

8
Document conventions and icons
Conventions
This section describes the conventions used in the documentation.
Port numbering in examples
The port numbers in this document are for illustration only and might be unavailable on your device.
Command conventions
Convention Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... } Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ] Square brackets enclose a set of optional syntax choices separated by vertical bars,
from which you select one or none.
{ x | y | ... } * Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select at least one.
[ x | y | ... ] * Asterisk marked square brackets enclose optional syntax choices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign
can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.
GUI conventions
Convention Description
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window appears; click OK.
> Multi-level menus are separated by angle brackets. For example, File > Create >
Folder.
Symbols
Convention Description
WARNING! An alert that calls attention to important information that if not understood or followed
can result in personal injury.
CAUTION: An alert that calls attention to important information that if not understood or followed
can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT: An alert that calls attention to essential information.
NOTE: An alert that contains additional or supplementary information.
TIP: An alert that provides helpful information.

9
Network topology icons
Convention Description
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that
supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access
controller engine on a unified wired-WLAN switch.
Represents an access point.
Represents a wireless terminator unit.
Represents a wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security
gateway, or load balancing device.
Represents a security card, such as a firewall, load balancing, NetStream, SSL VPN,
IPS, or ACG card.
T
T
T
T





10
Support and other resources
Accessing Hewlett Packard Enterprise Support
•For live assistance, go to the Contact Hewlett Packard Enterprise Worldwide website:
www.hpe.com/assistance
•To access documentation and support services, go to the Hewlett Packard Enterprise Support
Center website:
www.hpe.com/support/hpesc
Information to collect
•Technical support registration number (if applicable)
•Product name, model or version, and serial number
•Operating system name and version
•Firmware version
•Error messages
•Product-specific reports and logs
•Add-on products or components
•Third-party products or components
Accessing updates
•Some software products provide a mechanism for accessing software updates through the
product interface. Review your product documentation to identify the recommended software
update method.
•To download product updates, go to either of the following:
{Hewlett Packard Enterprise Support Center Get connected with updates page:
www.hpe.com/support/e-updates
{Software Depot website:
www.hpe.com/support/softwaredepot
•To view and update your entitlements, and to link your contracts, Care Packs, and warranties
with your profile, go to the Hewlett Packard Enterprise Support Center More Information on
Access to Support Materials page:
www.hpe.com/support/AccessToSupportMaterials
IMPORTANT:
A
ccess to some updates might require product entitlement when accessed through the Hewlett
Packard Enterprise Support Center. You must have an HP Passport set up with relevant
entitlements.

11
Websites
Website Link
Networking websites
Hewlett Packard Enterprise Information Library for
Networking www.hpe.com/networking/resourcefinder
Hewlett Packard Enterprise Networking website www.hpe.com/info/networking
Hewlett Packard Enterprise My Networking website www.hpe.com/networking/support
Hewlett Packard Enterprise My Networking Portal www.hpe.com/networking/mynetworking
Hewlett Packard Enterprise Networking Warranty www.hpe.com/networking/warranty
General websites
Hewlett Packard Enterprise Information Library www.hpe.com/info/enterprise/docs
Hewlett Packard Enterprise Support Center www.hpe.com/support/hpesc
Hewlett Packard Enterprise Support Services Central ssc.hpe.com/portal/site/ssc/
Contact Hewlett Packard Enterprise Worldwide www.hpe.com/assistance
Subscription Service/Support Alerts www.hpe.com/support/e-updates
Software Depot www.hpe.com/support/softwaredepot
Customer Self Repair (not applicable to all devices) www.hpe.com/support/selfrepair
Insight Remote Support (not applicable to all devices) www.hpe.com/info/insightremotesupport/docs
Customer self repair
Hewlett Packard Enterprise customer self repair (CSR) programs allow you to repair your product. If
a CSR part needs to be replaced, it will be shipped directly to you so that you can install it at your
convenience. Some parts do not qualify for CSR. Your Hewlett Packard Enterprise authorized
service provider will determine whether a repair can be accomplished by CSR.
For more information about CSR, contact your local service provider or go to the CSR website:
www.hpe.com/support/selfrepair
Remote support
Remote support is available with supported devices as part of your warranty, Care Pack Service, or
contractual support agreement. It provides intelligent event diagnosis, and automatic, secure
submission of hardware event notifications to Hewlett Packard Enterprise, which will initiate a fast
and accurate resolution based on your product’s service level. Hewlett Packard Enterprise strongly
recommends that you register your device for remote support.
For more information and device support details, go to the following website:
www.hpe.com/info/insightremotesupport/docs

12
Documentation feedback
Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To help
us improve the documentation, send any errors, suggestions, or comments to Documentation
Feedback ([e-mail]). When submitting your feedback, include the document title,
part number, edition, and publication date located on the front cover of the document. For online help
content, include the product name, product version, help edition, and publication date located on the
legal notices page.

13
Appendix A Chassis views and technical
specifications
Chassis views
HPE 1405 5G
Figure 8 Top panel
(1) Copper port LEDs (2) Power LED
Figure 9 Rear panel
(1) 10/100/1000BASE-T copper ports (2) DC Power receptacle

14
HPE 1405 8G
Figure 10 Top panel
(1) Copper port LEDs (2) Power LED
Figure 11 Rear panel
(1) 10/100/1000BASE-T copper ports (2) DC power receptacle
Technical specifications
Chassis dimensions and weights
Chassis Dimensions (H x W x D) Maximum weight
HPE 1405 5G 31.7 x 115 x 91.3 mm (1.25 × 4.52 × 3.59 in) 0.16 kg (0.35 lb)
HPE 1405 8G 31.7 x 155 x 91.3 mm (1.25 × 6.10 × 3.59 in) 0.22kg (0.49 lb)
Ports and interface card slots
Chassis 10/100/1000BASE-T auto-sensing Ethernet ports
HPE 1405 5G 5
HPE 1405 8G 8

15
Environmental specifications
Chassis Operating temperature Relative humidity
All chassis 0°C to 40°C (32°F to 104°F) 5% to 95%, noncondensing
Power specifications
DC input voltage specifications
Chassis Voltage
All chassis 12V DC
Power consumption specifications
Chassis Min. power consumption Max. power consumption
HPE 1405 5G 1 W 3 W
HPE 1405 8G 1 W 4.5 W

16
Appendix B LEDs
Power LED
Table 5 Power LED description
Status Description
Steady white The switch is powered on and the power supply is operating correctly.
Flashing white The switch is faulty if the LED flashes white for five seconds.
Off The switch is not powered on or the power supply is faulty.
Copper port LEDs
Link/ACT LEDs
Table 6 Link/ACT LED description
Status Description
Steady white A 10/100/1000 Mbps link is present.
Flashing white The port is receiving or sending data at 10/100/1000 Mbps.
Off No link is present.

17
Appendix C Troubleshooting
Table 7 describes the troubleshooting methods for common issues that you might encounter while
using and managing the switch.
If a problem persists, contact Hewlett Packard Enterprise Support.
Table 7 Troubleshooting methods
Symptom Troubleshooting method
Power LED off
1. Verify that the correct power source is used and the power
adapters are correctly connected.
2. Verify that the power source side provides power supply
correctly.
LAN interface LED off
1. Verify that the network cable is correctly connected to the
network port of the switch.
2. Insert the two ends of a network cable into two network ports of
the switch. If the port LEDs are off, replace the network cable.