HighPoint RR2720A User manual

Linux Ubuntu on RR2720A Installation Guide
HighPoint RR2720A
RAID Controller
Linux Ubuntu
Installation Guide
Copyright © 2023 HighPoint Technologies, Inc.
All rights reserved.
Last updated on April 03, 2023

Linux Ubuntu on RR2720A Installation Guide
i
Table of Contents
1 Overview .........................................................................................................................................1
2 Installing Linux Ubuntu on RR Series RAID controller ...........................................................1
Step 1 Prepare Your Hardware for Installation .......................................................................... 1
Step 2 Check System EFI Settings .............................................................................................1
Step 3 Flash UEFI Rom to RAID Controller ............................................................................. 3
Step 4 Create Array .....................................................................................................................4
Step 5 Prepare the Driver Diskette .............................................................................................5
Step 6 Install Linux Ubuntu ....................................................................................................... 5
3 Monitoring the Driver ...................................................................................................................8
4 Installing RAID Management Software ......................................................................................9
5 Troubleshooting ............................................................................................................................. 9
6 Rebuilding Driver Module for System Update .........................................................................10
7 Appendix A ................................................................................................................................... 10

Linux Ubuntu on RR2720A Installation Guide
- 1 -
1 Overview
The purpose of this document is to provide clear instructions on how to install Linux
Ubuntu on the RR Series RAID controller.
Supported system: Ubuntu 20.04/20.04.1/20.04.2.0/20.04.3/20.04.4/20.04.5/20.10/
22.04/22.04.1/22.10
Supported controller: RR2720A
2 Installing Linux Ubuntu on Series RAID controller
If you would like to install Linux Ubuntu onto drives attached to RR Series RAID
controller, please perform the following operations:
Step 1 Prepare Your Hardware for Installation
After you attach your hard disks to RAID controller, you can use EFI Utility to configure
your hard disks as RAID arrays, or just use them as single disks.
Before installation, you must remove all the Hard disks, which are not physically attached
to RAID controller, from your system.
Note
RAID Controller support EFI boot. If you have other SCSI adapters installed, you must
make sure the RR Series controller EFI will be loaded firstly. If not, try to move it to
another PCI slot. Otherwise you may be unable to boot up your system.
Step 2 Check System EFI Settings
In your system EFI SETUP menu, change Boot Sequence in such a way that the system
will first boot from EFI CDROM or EFI a Bootable USB drive, after you finish
installation, set RR Series RAID as the first boot device to boot up the system. Refer to
your motherboard EFI manual to see how to set boot sequence.
1. Set UEFI setting with SuperMicro X11DPi-NT motherboard as an example.
a. "Advanced->PCIe/PCI/PnP Configuration->CPUSlot PCI-E OPROM"
to "EFI". Suppose RAID Controller is connected to motherboard CPU1 Slot 2
PCI-E X16, then you should set "CPU1 Slot 2 PCI-E X16 OPROM" to "EFI";

Linux Ubuntu on RR2720A Installation Guide
- 2 -
b. Disable "Secure Boot", set "Attempt Secure Boot" to "Disabled".
2. Set UEFI setting with GA-X570 AORUS MASTER motherboard as an example.
a. Set " Boot->CSM Support " to "Enabled";
b. And" Boot-> Storage Boot Option Control " to "UEFI Only";

Linux Ubuntu on RR2720A Installation Guide
- 3 -
3. Set UEFI setting with ASUS PRIME X299 -DELUXE motherboard as an example:
a. Set "Boot from Storage Devices" to "UEFI driver first";
b. And "Boot Device Control" to "UEFI Only" or "UEFI and Legacy OPROM";
c. Set "OS Type" to "Other OS".
Step 3 Flash UEFI Rom to RAID Controller
For Example RR2720A：
Note ： Make sure your USB flash partition format is FAT32.
a. Unzip RR2720A UEFI package to root dir(/) of a USB flash drive, and insert the
USB flash drive to the motherboard;
b. Booting from the UEFI USB flash and enter the UEFI environment;

Linux Ubuntu on RR2720A Installation Guide
- 4 -
c. Command with “rr2720.nsh”, flash UEFI rom to RR2720A Controller and reboot;
Step 4 Create Array
a. Attach two hard disks to RR2720A Controller;
b. Boot, enter the motherboard’s Boot List and select start from UEFI USB flash:
c. Command “ArrayCreate.efi” to enter the Utility:
d. Command “create RAID0”.
Create RAID0 array with all disks and with maximum capacity.
e. Command “exit”；
f. For more command usages, refer to Appendix A.

Linux Ubuntu on RR2720A Installation Guide
- 5 -
Step 5 Prepare the Driver Diskette
Extract RR272x_1x_ubuntuxx.xx.x_x86_64_vx.xx.xx_xx_xx_xx.tar.gz to top(/)
directory of an USB flash drive. It will look like:
Step 6 Install Linux Ubuntu
For Example：Ubuntu20.04.5 Server
a. Before you do the following, verify the status of your network environment. To
ensure a proper installation, it is recommended to disconnect the network and install
the system in a network less environment.
b. Insert the USB flash drive to the target system.
c. Booting from Bootable USB drive (EFI mode).
d. When the following window appears during the installation process
Press ALT+F2 to switch to the shell on console 2 and press ENTER to activate this
console.
If you use Ubuntu Desktop, please press CTRL+ALT+F2 to switch to the shell on console
2 and press ENTER to activate this console.

Linux Ubuntu on RR2720A Installation Guide
- 6 -
Ubuntu login: ubuntu
And then execute following commands to copy the driver contents:
# mkdir /hptdd ← Create mount point for USB flash drive
# mount /dev/sdb1 /hptdd/ ← Mount the USB flash drive to /hptdd
# cp -a /hptdd/hptdd /tmp/ ← Copy driver installation file to system temporary
directory
# umount /dev/sdb1 ← Unmount the USB flash drive
When the USB flash drive is unmounted, please unplug the USB flash drive from the
mainboard. And then execute following command to install driver to install the Linux
Ubuntu.
# sh /tmp/hptdd/preinst.sh ← Load RR2720A driver.
e. Then press ALT+F1 to switch back to installation screen and continue the installation as
usual.
f. When the screen shows that “install complete”.

Linux Ubuntu on RR2720A Installation Guide
- 7 -
press ALT+F2 to the shell and type the following commands:
If you use Ubuntu20.04.5 desktop , When the installation prompts“Installation Complete”,
don’t click Restart Now . please press CTRL+ALT+F2 and execute following commands.
# sh /tmp/hptdd/postinst.sh ← Install RR2720A driver.
A message will be displayed that the driver has been installed successfully.
g. Press ALT+F1 and press Reboot Now to finish the installation.
h. If you want to boot from another kernel, please install the RR Series opensource driver
after entering the system.
i. Restart to enter the system, please connect to the internet:
01. use “apt-get update” to retrieve new lists of ubuntu packages

Linux Ubuntu on RR2720A Installation Guide
- 8 -
02. Linux opensource driver link, open the following link to enter the "Software
Download" page to download:
RR2700 Series: https://www.highpoint-tech.com/rr272x-overview
Extract driver package:
tar zxvf RR272x_1x_Linux_X86_64_Src_vx.x.x_xx_xx_xx.tar.gz
Run the .bin file to install the driver package.
sh rr272x_1x-linux-src-vxx.x.x-xx_xx_xx.bin or
./rr272x_1x-linux-src-vxx.x.x-xx_xx_xx.bin
a. Follow the prompts to complete the driver installation.
b. After the installation is complete, you can perform system update operations.
3 Monitoring the Driver
Once the driver is running, you can monitor it through the Linux proc file system support.
There is a special file under /proc/scsi/rr272x_1x /. Through this file you can view driver
status and send control commands to the driver.
Note
The file name is the SCSI host number allocated by OS. If you have no other SCSI cards
installed, it will be 0. In the following sections, we will use x to represent this number.
Using the following command to show driver status:
#cat /proc/scsi/rr272x_1x /x
This command will show the driver version number, physical device list and logical device
list.