HighPoint R1000 Series User manual

1
R1108
8x M.2 Port to PCIe 3.0x16 NVMe HBA
Quick Installation Guide
V1.00

2
System Requirements
PC Requirements
•System with a free PCIe3.0 (or 4.0) x16 slot
•Windows 10 or later, Windows Server 2019
•Linux Kernel 3.10 or later
•macOS 10.13 or later
•FreeBSD 12.1 and later
R1108 Kit Content
•R1108 Controller Card
•Quick Installation Guide

3
R1108 Hardware
Front View
Low-Noise fans
Full-length anodized aluminum heat sink
PCIe 3.0 x16 Host Interface

4
R1108 Hardware Installation:
Step 1. On the rear of the R1108, remove the six screws that secure the
unit’s heat sink to the PCB.
Step 2. Carefully remove fan’s power cable from the right-side of the
heatsink as shown below, then carefully flip the heatsink to the
left (like turning a page from a book).
Note: Take care when moving the heatsink to prevent damaging
the left fan’s power cable.

5
Step 3. This will expose the two thermal pads. The blue film must be
removed from each pad before reinstalling this panel. This film
protects the pads from damage and foreign objects prior to
installation, but will also prevent the pad from transferring heat
away from the NVMe SSD’s and controller componentry.
Step 4. These 8 screws are used to install the NVMe SSD’s.

6
Step 5. Please remove these screws from each of the M.2 slots.
Step 6. Gently insert the SSD into the slot.
Step 7. Refasten the screw to secure the SSD.
Repeat Steps 5 to 7 to install the remaining SSDs.
The following example shows eight M.2 SSDs installed into Ports 1-8:

7
Step 8. After installing all SSDs, carefully flip the heatsink to the right.
Note: Make sure the SSD’s are carefully, but securely installed
into each M.2 port. Loose connections can cause a variety of
stability and performance issues, and may ultimately result in
data loss.
Note: Make sure the heatsink/fan panel is properly aligned with
the controller board (PCB), and that it makes full contact with the
thermal pads before refastening it to the NVMe HBA. If the
heatsink is improperly installed, it will be unable to sufficiently
cool the NVMe SSD’s and controller componentry, which may
result in damage to the SSD’s or controller hardware,
performance loss, unstable I/O, and the loss of data.
Step 9. Carefully reinsert in the power supply cable of the cooling fan
that was removed in step 2.

8
Step 10. On the rear of the R1108, refasten the 6 screws that were
removed in step 1.
Step 11. Power up the SSD external power supply
Note: If the external power supply is not powered on, the SSDs
may drop offline or remain undetected, which could lead to data
loss.
R1108 relies on two power sources to support eight SSDs; power
supplied through the PCIe bus, and power from the system’s PSU
via an external power cable. If the external cable is not connected,
there will be insufficient power to support all 8 SSD’s; this may
cause the SSDs to drop offline.

9
Note ： The R1108 does not require the external power cord when
used with 2019 Mac Pro systems.

10
Resources
We recommend visiting the R1108 Series Product Page for the latest
documentation.
Document Downloads:
https://www.highpoint-tech.com/USA_new/series-r1000-fan-overview.html
Customer Support
If you encounter any problems while utilizing the R1108, or have any
questions about this or any other HighPoint Technologies, Inc. product,
feel free to contact our Customer Support Department.
Web Support:
https://www.highpoint-tech.com/websupport/main.php
HighPoint Technologies, Inc. websites:
https://www.highpoint-tech.com
© Copyright 2021 HighPoint Technologies, Inc. All rights reserved.