HIK VISION DS-TMG4B1 User manual

Barrier Gate
User Manual

Barrier Gate User Manual
1
© 2023 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
ALL RIGHTS RESERVED.
This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates
(hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed, translated, or
distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Unless otherwise expressly stated herein, Hikvision does not make any warranties, guarantees or
representations, express or implied, regarding to the Manual, any information contained herein.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Manual is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version of this Manual at the Hikvision website
(https://www.hikvision.com/).
Please use this Manual with the guidance and assistance of professionals trained in supporting the
Product.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in
various jurisdictions.
Other trademarks and logos mentioned are the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH
ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR
PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION
BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,
WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY,
OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS,
AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS
INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE
SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT
INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF
PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS.

Barrier Gate User Manual
2
YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE
DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR
PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED
TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN
RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.

Barrier Gate User Manual
3
Regulatory information
FCC information
Please take attention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his
own expense.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as
unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of
as unsorted municipal waste in the European Union. See the product documentation for
specific battery information. The battery is marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Barrier Gate User Manual
4
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Provides additional information to emphasize or
supplement important points of the main text.
Indicates a potentially hazardous situation, which
if not avoided, could result in equipment
damage, data loss, performance degradation, or
unexpected results.
Indicates a hazard with a high level of risk, which
if not avoided, will result in death or serious
injury.
Safety Instructions
Laws and Regulations
Use of the product must be in strict compliance with the local laws and regulations. Please shut
down the device in prohibited area.
Power Supply
Use of the product must be in strict compliance with the local electrical safety regulations.
Use the power adapter provided by qualified manufacturer. Refer to the product specification
for detailed power requirements.
It is recommended to provide independent power adapter for each device as adapter overload
may cause over-heating or a fire hazard.
Make sure that the power has been disconnected before you wire, install, or disassemble the
device.
DO NOT directly touch exposed contacts and components once the device is powered up to
avoid electric shock.
DO NOT use damaged power supply devices (e.g., cable, power adapter, etc.) to avoid electric
shock, fire hazard, and explosion.
DO NOT directly cut the power supply to shut down the device. Please shut down the device
normally and then unplug the power cord to avoid data loss.
DO NOT block the power supply equipment to plug and unplug conveniently.
Make sure the power supply has been disconnected if the power adapter is idle.
Make sure the device is connected to the ground firmly.
Transportation, Use, and Storage
To avoid heat accumulation, good ventilation is required for a proper operating environment.
Avoid lightning strike for device installation. Install a lightening arrester if necessary.

Barrier Gate User Manual
5
Keep the device away from magnetic interference.
Avoid device installation on vibratory surface or places, and avoid equipment installation on
vibratory surface or places subject to shock (ignorance may cause device damage).
DO NOT touch the heat dissipation component to avoid burns.
DO NOT expose the device to extremely hot, cold, or humidity environments. For temperature
and humidity requirements, see device specification.
Maintenance
If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the
power cable, and contact the service center.
If the device is abnormal, contact the store you purchased it or the nearest service center. DO
NOT disassemble or modify the device in any way (For the problems caused by unauthorized
modification or maintenance, the company shall not take any responsibility).
Keep all wrappers after unpacking them for future use. In case of any failure occurred, you
need to return the device to the factory with the original wrapper. Transportation without the
original wrapper may result in damage to the device and the company shall not take any
responsibility.

Barrier Gate User Manual
6
Table of Contents
CHAPTER 1 INTRODUCTION..........................................................................................................7
1.1 PRODUCT INTRODUCTION ............................................................................................................ 7
1.2 KEY FEATURE............................................................................................................................ 7
1.2.1 Mechanical Feature ....................................................................................................7
1.2.2 Electrical Feature........................................................................................................7
1.2.3 Safety Feature ............................................................................................................8
1.3 PACKING LIST ........................................................................................................................... 8
1.4 DIRECTION .............................................................................................................................. 8
1.5 SAFETY INSTRUCTION ................................................................................................................. 9
CHAPTER 2 INTERNAL STRUCTURE .............................................................................................10
2.1 INTERNAL STRUCTURE OVERVIEW ................................................................................................ 10
2.2 MACHINE CORE STRUCTURE ...................................................................................................... 10
CHAPTER 3 WIRING....................................................................................................................13
CHAPTER 4 DIMENSION .............................................................................................................14
CHAPTER 5 BARRIER GATE COMPONENT....................................................................................15
5.1 BARRIER GATE WITH STRAIGHT BOOM POLE .................................................................................. 15
5.2 BARRIER GATE WITH CURVED BOOM POLE .................................................................................... 16
CHAPTER 6 INSTALLATION .......................................................................................................... 18
6.1 INSTALLATION DESCRIPTION ....................................................................................................... 18
6.2 INSTALLATION ......................................................................................................................... 18
6.3 INSTALLATION DEBUG ............................................................................................................... 19
CHAPTER 7 REMOTE CONTROL...................................................................................................20
7.1 BUTTON DESCRIPTION .............................................................................................................. 20
7.1.1 Independent Button..................................................................................................20
7.1.2 Button Combination..................................................................................................20
7.2 DIP SWITCH DESCRIPTION ......................................................................................................... 21
7.3 LIMIT POSITION LEARNING MODE DESCRIPTION.............................................................................. 21
7.4 STATUS INDICATOR DESCRIPTION ................................................................................................. 21
7.5 REMOTE CONTROL DEBUG......................................................................................................... 22
CHAPTER 8 MAINTENANCE ........................................................................................................24

Barrier Gate User Manual
7
Chapter 1 Introduction
1.1 Product Introduction
Barrier gate is the entrance and exit management device to limit motor vehicle passing. It can
control the boom pole automatically via parking lot management system. Or you can control the
boom pole via buttons on remote controller.
Barrier gate is widely applicable to toll station, parking lot, the entrance and exit of community
and unit, etc.
1.2 Key Feature
1.2.1 Mechanical Feature
The housing is solid, durable, and waterproof, adaptive to outdoor application.
Integrated machine core design to guarantee stability and running accuracy.
Equipped with 60 W integrated worm and gear transmission deceleration asynchronous motor
with stable transmission, low noise, and compact structure. It supports self-lock. No impact
when the rotor is locked to protect the controller and increase the service life of the controller.
Adopts exact four-bar linkage mechanism to keep the boom pole running rapidly and stably,
and release the motor load to increase the service life.
Supports manual lock. You can rotate the hand wheel on the bottom of motor to control the
boom pole manually when the power is cut off.
1.2.2 Electrical Feature
Highly integrated system, connectable to multiple matched devices conveniently.
Adopts rising/falling timeout protection to protect motor effectively, guaranteeing the
all-weather running of the barrier gate and avoiding the abnormal damages.
Adopts angle sensor to detect the boom pole position with high accuracy to guarantee the
stable running.
Abundant status indicators to make it convenient to use and maintain.
Standard remote control and smart learning. Supports ten groups of remote control codes.
Adopts magnetic core transformer to ensure the barrier gate to work stably in outdoor
damping environment.
Integrated with light, electricity, and mechanical control. Flexible and convenient operation.
Safe and reliable usage.

Barrier Gate User Manual
8
1.2.3 Safety Feature
Resistance rebound. If the boom pole is resistant during falling, it can rebound automatically.
Induction anti-collision. When the boom pole is falling while the induction signal is received,
the boom pole will rise automatically and keep rising during the triggering process. After the
induction signal restores, the boom pole will fall automatically to guarantee safety.
Rising signal first. When the boom pole is falling, if something emergency happens, it will rise
once receiving the rising signal.
Rubber strip anti-collision. The rubber strip on the boom pole can help to decrease damages
caused by accident.
1.3 Packing List
Table 1-1 Packing List
No.
Name
Quantity
1
Barrier gate host
1
2
Button switch
1
3
User manual
1
4
Certification
1
5
Accessory package
1
6
Remote controller
2
7
Key
2
1.4 Direction
The boom pole direction can be adjusted from left to right or from right to left.

Barrier Gate User Manual
9
Figure 1-1 Boom Pole Direction
1.5 Safety Instruction
Conform to the following instructions for your safety.
DO NOT open the host door or cover when the device is working.
The internal wiring of the device has been completed when leaving factory. In normal
conditions, DO NOT change the wiring. Just connect to the power supply.
Make sure the device is connected to the ground firmly.
DO NOT place any object under the boom pole. No person is allowed to stand or move under
the boom pole when it is falling.
When the power is cut off, shut down the power supply first, and then rotate the boom pole
to the vertical status with hand wheel.
The boom pole and the spring have been matched to the best status when the device leaves
factory. DO NOT increase or decrease the boom pole length or weight randomly to avoid the
danger that the boom pole may lose balance. If you need to increase or decrease, contact the
professionals.
Contact the professionals to connect to peripheral IR protection equipment.

Barrier Gate User Manual
10
Chapter 2 Internal Structure
2.1 Internal Structure Overview
The internal structure of the barrier gate host is run by the worm and gear transmission
deceleration asynchronous motor. The movement is transmitted to the main shaft via four-bar
linkage mechanism. The angle sensor can detect the rotation angle of the output shaft, and locate
the position of the boom pole accurately.
Refer to the figure below for the internal structure overview.
Figure 2-1 Internal Structure
2.2 Machine Core Structure
Refer to the figure below for the machine core structure.

Barrier Gate User Manual
11
Figure 2-2 Machine Core Structure
There are extension springs installed inside the barrier gate host. During installation and debug,
you can adjust the diameter and quantity of the springs according to the length of the boom pole
to reach the moment balance. Refer to the table below to select the springs.
Table 2-1 Spring Description
Boom Pole Type
Boom Pole
Length Range
Hole
Quantity
Spring Quantity
and Type
Non-telescopic straight
boom pole
L ≤ 3 m
1
2 × φ 4.5
3 m ＜L ≤ 3.5
m
2
2 × φ 4.5
3.5 m ＜L ≤
4.2 m
1
2 × φ 5.5
4.2 m ＜L ≤
4.7 m
2
2 × φ 5.5
4.7 m ＜L ≤ 6
m
3
2 × φ 5.5
Telescopic straight
L ＜3 m
1
2 × φ 4.5

Barrier Gate User Manual
12
boom pole/Curved
boom pole
3 m ≤ L ＜3.5
m
2
2 × φ 4.5
3.5 m ≤ L ≤ 4 m
3
2 × φ 4.5
4 m ＜L ＜
5 m
1
2 × φ 5.5
5 m ≤ L ≤ 6 m
2
2 × φ 5.5
If the boom pole length changes, select the spring type again according to the table above, and
adjust corresponding parameters.

Barrier Gate User Manual
13
Chapter 3 Wiring
Refer to the figure below for the wiring of barrier gate.
Figure 3-1 Wiring

Barrier Gate User Manual
14
Chapter 4 Dimension
Refer to the figure below for the dimension of the barrier gate with non-telescopic straight boom
pole.
Figure 4-1 Dimension
For the barrier gate with telescopic straight boom pole or curved boom pole, the dimensions of the
host and base are the same as above.

Barrier Gate User Manual
15
Chapter 5 Barrier Gate Component
5.1 Barrier Gate with Straight Boom Pole
Refer to the figure and table below for the component description of the barrier gate with straight
boom pole.
Figure 5-1 Barrier Gate Component (1)

Barrier Gate User Manual
16
Table 5-1 Barrier Gate Component Description (1)
No.
Name
Quantity
1
Barrier gate host
1
2
Boom pole
1
3
Cross recessed pan head screw M3 × 8
1
4
Boom pole mounting housing
1
5
Hexagon head bolt M8 × 65
4
6
Flat washer φ 8
4
7
Boom pole mounting cushion block
1
8
Main shaft mounting
1
9
Hexagon check nut M8
4
10
Boom pole mounting housing label
1
5.2 Barrier Gate with Curved Boom Pole
Refer to the figure and table below for the component description of the barrier gate with curved
boom pole.
Figure 5-2 Barrier Gate Component (2)

Barrier Gate User Manual
17
Table 5-2 Barrier Gate Component Description (2)
No.
Name
Quantity
1
Barrier gate host
1
2
Boom pole
1
3
Cross recessed pan head screw M3 × 8
1
4
Boom pole mounting housing
1
5
Hexagon head bolt M8 × 65
4
6
Flat washer φ 8
4
7
Boom pole mounting cushion block
1
8
Main shaft mounting
1
9
Hexagon check nut M8
4
10
Boom pole mounting housing label
1
11
Hexagon head bolt M10 × 30
3
12
Flat washer φ 10
5
13
Hexagon check nut M10
1

Barrier Gate User Manual
18
Chapter 6 Installation
6.1 Installation Description
Cut off power before installation.
Open the package, and check the accessories according to the accessory checklist.
Confirm the installation position of the barrier gate host according to the boom pole direction
and the actual condition of the installation site. For the non-concrete foundation or the
position with slope, it is recommended to build the concrete foundation first. Make sure the
base of the barrier gate host can be fixed firmly on the foundation, and the perpendicularity of
the host to the horizontal plane is smaller than 1°.
Lay power cables and control wires tubes according to corresponding regulations and the
position of the control room. It is recommended that the power cables and control wires are
laid in different tubes.
Install expansion screws on the installation position of the host to fix the host firmly.
Rotate the crank handle to set the boom pole to the horizontal position to confirm the
installation position of the support rod at the end of the boom pole, and fix the support rod
firmly with screws (Ignore this if there is no support rod).
Connect the power cables and control wires to the control board of the host according to the
wiring diagram. Fasten them and start debug after confirming the connection is correct.
6.2 Installation
Before you start:
Confirm the position to fix the host. Build the concrete foundation if needed. The dimension of the
foundation should be approximate 100 to 150 mm larger than that of the host bottom.
Steps:
1. Bury cables.
1) Dig a ditch and bury cable tubes between the center of the host fixed position and the
control room.
2) Pass 3 × 1.5 mm²power cables and 4 × 0.5 mm²control wires through the tubes.
3) Fill the ditch with concrete.
2. Fix the host.
1) Put the host on the pre-confirmed position. Open the door, and make marks of the
installation holes’ centers on the bottom and the host base margins.
2) Remove the host, and punch holes on the marked positions of the screws.

Barrier Gate User Manual
19
The drill size should be matched with the attached expansion screw, and the hole depth should
meet the requirement of the expansion screw length.
3) Put the host on the pre-confirmed position. Punch expansion screws into the bottom
holes and fasten them firmly.
3. Install the boom pole.
1) Install the boom pole to the main shaft mounting on the host, and fasten the screws to
make sure the boom pole does not tilt.
2) (Optional) If support rod is needed, debug the horizontal and vertical status of the boom
pole, rotate the crank handle to set the boom pole to the horizontal position to confirm
the installation position of the support rod at the end of the boom pole, and fix the
support rod firmly with screws.
4. Install peripheral devices.
1) After the barrier gate installation and debug completes, wire the lines in the host and
connect the control lines of the peripheral devices according to the wiring diagram.
2) Debug the devices.
6.3 Installation Debug
Problem
Debug Method
The boom pole is not on the
horizontal/vertical position.
1. Unfasten the two screws on the main shaft crank arm,
and set the boom pole to the horizontal position.
2. Learn the horizontal limit position, and fasten the
screws.
3. Adjust the vertical position of the boom pole to
appropriate angle, and learn the vertical limit position.
The boom pole shakes during rising.
The spring is too tight. Adjust the spring holes, or unfasten
the adjustment lever to adjust the spring tightness.
The boom pole shakes during falling.
The spring is too loose. Adjust the spring holes, or fasten
the adjustment lever to adjust the spring tigntness.