HIK VISION DS-7304HFI-S User manual

InstallationGuide
DS-7300HFI-S Series DVR (V3.1.0)
VerifyContents
Verify that the package contents are correct by checking the
items against the packing list.
Installation Guide – DS-7300HFI-S Series DVR 1

Note: Please contact your dealer for damaged or missing
items.
DVRPre‐Installation
The DS-7300HFI-S Series DVR is highly advanced
surveillance equipment that should be installed with care.
Please take into consideration the following precautionary
steps before installation of the DVR.
1. Keep all liquids away from the DVR.
2. Install the DVR in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory
specifications.
4. Install a manufacturer recommended HDD.
DVRInstallation
During the installation of the DVR:
1. Use brackets for rack mounting.
2. Ensure there is ample room for audio and video cables.
3. When installing cables, ensure that the bend radius of the
cables are no less than five times than it’s’ diameter.
4. Connect both the alarm and RS-485 cable.
5. Allow at least 2cm (~0.75in) of space between racks
mounted devices.
6. Ensure the DVR is grounded.
7. Environmental temperature should be within the range of
-10ºC ~ 55ºC, 14ºF ~ 131ºF.
8. Environmental humidity should be within the range of
10% ~ 90%.
HardDiskInstallation
Before installing a hard disk drive (HDD), please make sure
the power is disconnected from the DVR. A factory
recommended HDD should be used for this installation.
Tools Required: Screwdriver.
To install a HDD on your DVR:
1. Remove the cover from
the DVR by unfastening
the screws on the back
and side.
2. Install the HDD in the
HDD rack using the
provided screws.
Fasten the screws on
the button to fix the
HDD.
3. Connect the HDD to the
motherboard of the
DVR with the included
data cable.
4. Connect the power
cable to the HDD.
5. Re-install the cover of
the DVR and fasten
screws.
alarm shop


RearPanelDiagram
DS‐7304HFI‐SRearPanel:
No.Item Description
MAIN VIDEO OUT
BNC connector for main video output. If VGA is connected, the MAIN VIDEO
OUT will not function. If VGA is not connected, it is used as the main video output
with local video display and menu operations.
1
SPOT VIDEO OUT BNC connector for spot monitor. Single window-division view.
2 VIDEO IN BNC connectors for analog video input.
3AUDIO IN RCA connectors for analog audio input.
4LINE IN RCA connector for audio input.
5AUDIO OUT RCA connector for audio output. This connector is synchronized with VIDEO
OUT.
6VGA VGA output. Display local video output and menu.
7RS-232 DB9 connector for RS-232 devices.
8LAN Interface Connector for LAN (Local Area Network)
9USB Interface Connector for USB devices.
10VIDEO LOOP OUT Connector for video loop output.
11Termination Switch Connection of 120-ohm terminator for RS-485 bus. ON=connected;
OFF=disconnected.
RS-485 Interface Connectors for RS-485 devices. T+, T- pin connects to PTZ.
KB Control Interface D+, D- pin are connected to Ta, Tb pin of controller. For cascading devices, the
first DVR’s D+, D- pin should be connected with the D+, D- pin of the next DVR.
ALARM IN Connector for alarm input.
12
ALARM OUT Connector for alarm output.
13GND Grounding(needs to be connected when DVR starts up).
14100~240VAC 100~240VAC power supply.
15POWER Switch for turn on/off the device.
2 Installation Guide - DS-7300HFI-S Series DVR
alarm shop



DS‐7308/7316HFI‐SRearPanel:


No.Item Description
MAIN VIDEO OUT
BNC connector for main video output. If VGA is connected, the MAIN VIDEO
OUT will not function. If VGA is not connected, it is used as the main video
output with local video display and menu operations.
1
SPOT VIDEO OUT BNC connector for spot monitor. Single window-division view.
2 VIDEO IN BNC connectors for analog video input.
3AUDIO IN RCA connectors for analog audio input.
4LINE IN RCA connector for audio input.
5AUDIO OUT RCA connector for audio output. This connector is synchronized with VIDEO
OUT.
6VIDEO LOOP OUT Connector for video loop output.
7VGA VGA output. Display local video output and menu.
8RS-232 DB9 connector for RS-232 devices.
9LAN Interface Connector for LAN (Local Area Network)
10USB Interface Connector for USB devices.
11Termination Switch Connection of 120-ohm terminator for RS-485 bus. ON=connected;
OFF=disconnected.
RS-485 Interface Connectors for RS-485 devices. T+, T- pin connects to PTZ.
KB Control Interface
D+, D- pin are connected to Ta, Tb pin of controller. For cascading devices, the
first DVR’s D+, D- pin should be connected with the D+, D- pin of the next
DVR.
ALARM IN Connector for alarm input.
12
ALARM OUT Connector for alarm output.
13GND Grounding(needs to be connected when DVR starts up).
14100~240VAC 100~240VAC power supply.
15POWER Switch for turn on/off the device.
Installation Guide - DS-7300HFI-S Series DVR 3
alarm shop


PeripheralConnections
ConnectingtoAlarmInput/OutputDevice

The alarm input/output interface of the DVR is shown below:
The alarm input is an open/close relay. If the input is not an
open/closed relay, follow the connection diagram below:
To connect to an AC/DC load, use the following diagram:
For DC load, JP4 can be used within the limit of 12V/1A
safely. If the interface is connected to an AC load, JP4 should
be left open. Use an external relay for safety (as shown in the
figure above).
There are 4 jumpers (JP4, JP5, JP6, and JP7) on the
motherboard, each corresponding with one alarm output. By
default, jumpers are connected. To connect an AC load,
jumpers should be removed.
Note: An external relay is needed to prevent electric shock
when connecting to an AC load.
AlarmConnection
To connect alarm devices to the DVR:
1. Disconnect pluggable block from the ALAM IN
/ALARM OUT terminal block.
2. Unfasten stop screws from the pluggable block, insert
signal cables into slots and fasten stop screws. Ensure
signal cables are in tight.
3. Connect pluggable block back into terminal block.

RS‐485Connection

To connect RS-485 devices to the DVR:
1. Disconnect pluggable block from the RS-485 terminal
block.
2. Unfasten stop screws from the pluggable block, insert
signal cables into slots and fasten stop screws. Ensure
signal cables are in tight.
3. Connect pluggable block back into terminal block.
4 Installation Guide - DS-7300HFI-S Series DVR
alarm shop


Note: The RS-485 PTZ control should be connected with
the T+ and T- pin on the RS-485 terminal block.
To connect a controller to the DVR:
1. Disconnect pluggable block from the KB terminal block.
2. Unfasten stop screws from the KB D+, D- pluggable
block, insert signal cables into slots and fasten stop
screws. Ensure signal cables are in tight.
ControllerConnection
3. Connect Ta on controller to D+ on terminal block and Tb
on controller to D- on terminal block. Fasten stop screws.
4. Connect pluggable block back into terminal block.
Note: Make sure both the controller and DVR are grounded.
Installation Guide - DS-7300HFI-S Series DVR 5
alarm shop


Specifications

Model DS-7304HFI-S DS-7308HFI-S DS-7316HFI-S
Video compression H.264
Video input 4-ch 8-ch 16-ch
Video input
interface BNC(1.0Vp-p, 75Ω), PAL/NTSC adaptive
Audio compression OggVorbis
Audio input 4-ch, RCA(2.0Vp-p, 1kΩ)
Video/Audio
input
Voice talk input 1-ch, RCA(2Vp-p, 1kΩ)
Preview resolution PAL: 704×576 NTSC: 704×480
VGA output 1-ch, Resolution: 1024×768/60Hz
Encoding
resolution 4CIF/DCIF/2CIF/CIF/QCIF
Video output 2-ch, BNC(1.0Vp-p, 75Ω)
Resolution: PAL: 704×576, NTSC: 704×480
1 video spot output
Video loop out 4-ch 8-ch 16-ch
Frame rate PAL: 1/16-25fps, NTSC:1/16-30fps
Video bit rate 32Kbps~2048Kbps, or user-defined
Audio output 1-ch, RCA(Linear, 600Ω)
Audio bit rate 16kbps
Dual stream Support(sub stream at CIF resolution)
Stream type Video/Video & Audio
Video/Audio
output
Synchronous
playback 4-ch 8-ch 16-ch
Type 4 SATA Interfaces
Hard disk Capacity Each supports up to 2TB capacity
Network interface 1, RJ45 10M/100M/1000M adaptive Ethernet interface
Serial interfaces 1 RS-232 serial interface; 1 RS-485 serial interface
USB interface 2, USB2.0
Alarm in 4 16 16
External
interfaces
Alarm out 2 4 4
Power supply 100~240VAC, 6.3A, 50~60Hz
Consumption ≤50W(without hard disk or DVD-R/W)
Working
temperature -10℃~+55℃
Working humidity 10%~90%
Chassis 19” standard 1.5U chassis
Size(mm) 70mm(H)×440mm(W)×390mm(D)
Others
Weight ≤8Kg(without hard disk or DVD-R/W)
6 Installation Guide - DS-7300HFI-S Series DVR
alarm shop



HDDStorageCalculationChart
The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate.
Bit Rate Storage Used
96K 42M
128K 56M
160K 70M
192K 83M
224K 98M
256K 112M
320K 140M
384K 168M
448K 196M
512K 225M
640K 281M
768K 337M
896K 393M
1024K 450M
1280K 562M
1536K 675M
1792K 787M
2048K 900M
Note: Please note that supplied values for storage space used is just for reference. Storage space used is estimated by formulas
and may have some deviation from actual value.
Installation Guide - DS-7300HFI-S Series DVR 7
alarm shop