HIK VISION DS-6701HFI User guide

Network Audio/Video Encoder
Quick Operation Guide
UD.6L0202B1455A01

Quick Operation Guide of DS-6700 Series Network Audio/Video Encoder
1
Installation
Pre-Installation
The DS-6700 Series Audio/Video Encoder is a highly advanced surveillance equipment that should
be installed with care. Please take into consideration the following precautionary steps before
installation of the Encoder.
1. Keep all liquids away from the Encoder.
2. Install the Encoder in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory specifications.
4. Install a manufacturer recommended HDD (for DS-6700HWI / HFI-SATA).
Installation
During the installation of the Encoder:
1. Use brackets for rack mounting.
2. Ensure there is ample room for audio and video cables.
3. When installing cables, ensure that the bend radius of the cables are no less than five times than
its diameter.
4. Connect both the alarm and RS-485 cable.
5. Allow at least 2cm (≈0.75in) of space between racks mounted devices.
6. Ensure the Encoder is grounded.
7. Environmental temperature should be within the range of -10 ºC ~ 55 ºC , 14ºF ~ 131ºF.
8. Environmental humidity should be within the range of 10% ~ 90%.
Hard Disk Installation
This section is applicable to DS-6700HWI/HFI-SATA models only which can be installed with
HDD for recording.
Prior to Installation
The device is factory installed with no hard disk. Refer to the following instructions to install the
hard disk according to the total capacity calculated in terms of the Schedule Recording Settings. The
installation and removal of the hard disk should be operated by qualified professionals.
Before installing a hard disk drive (HDD) for DS-6700HWI / HFI-SATA, please make sure the
power is disconnected from the device. A factory recommended HDD should be used for this
installation.
Tools Required: Screwdriver.
Steps:
1. Use the screwdriver to unfasten the screws on both sides and rear panel of the device, and then
remove the cover from the chassis.
2. Place the HDD into the slot of the chassis and then secure it in position by fastening the screws
at the bottom of the chassis.

Quick Operation Guide of DS-6700 Series Network Audio/Video Encoder
2
3. Take out the HDD data line from the accessories box. Plug one end of the data line to the
circuit board and the other end to the data line port of HDD. Connect the power cord to HDD
in the same way.
4. Replace the cover and then tighten the screws on both sides and rear panel of the device.

Quick Operation Guide of DS-6700 Series Audio/Video Encoder
3
Front Panel
DS-6701HWI/HFI:
Description of front panel:
Item
Description
1
POWER LED Indicator
Light in red when the device is powered on; light in orange when the SD
card is inserted.
2
VIDEO IN
BNC connector for video input.
3
LINE IN
3.5mm interface for two-way audio input or audio input; connect to audio
input device or active pick-up, microphone, etc.
4
AUDIO OUT
3.5mm interface; connect to audio output device, e.g., loudspeaker, etc.
5
microSD
microSD interface for data storage.
6
Reset
Restore the factory default settings by holding the RESET button for more
than 15 seconds after power is turned on.
DS-6704HWI/HFI:
Description of front panel:
Item
Description
1
POWER LED Indicator
Light in red when the device is powered on; light in orange when the SD
card is inserted.
2
LINE IN
3.5mm two-way audio input interface; connect to active pick-up,
microphone, etc.
3
AUDIO OUT
3.5mm interface; connect to audio output device, e.g., loudspeaker, etc.
4
VIDEO IN
BNC interface for video input.
5
AUDIO IN
Line input interface for audio input.

Quick Operation Guide of DS-6700 Series Audio/Video Encoder
4
DS-6708HWI/HFI and DS-6708HWI/HFI-SATA:
123
Description of front panel:
Indicator
Description
1
POWER
Lights in red when the device is powered on.
2
STATUS
Lights in red when data is being read from or written to HDD.
Valid for DS-6708HWI/HFI-SATA model only.
3
Tx/Rx
1. Does not light when the network is not connected;
2. Blinks in green when the data is transmitting / receiving;
3. Blinks at higher frequency when the data for transmitting / receiving is
larger.
DS-6716HWI/HFI and DS-6716HWI/HFI -SATA:
123
Description of front panel:
Indicator
Description
1
POWER
Lights in red when the device is powered on.
2
STATUS
Lights in red when data is being read from or written to HDD.
Valid for DS-6716HWI/HFI-SATA model only.
3
Tx/Rx
1. Does not light when the network is not connected;
2. Blinks in green when the data is transmitting / receiving;
3. Blinks at higher frequency when the data for transmitting / receiving is
larger.

Quick Operation Guide of DS-6700 Series Audio/Video Encoder
5
Rear Panel
DS-6701HWI/HFI:
Description of rear panel:
Item
Description
1
ALARM IN /OUT
Relay alarm input/output.
Note: The alarm output terminal provides no JP2 pin.
2
RS-485
RS-485 serial interface; connect to pan/tilt unit, speed dome, etc.
3
LAN
10M/100Mbps adaptive Ethernet interface (PoE).
The right LED indicator lights in green when the network cable is connected,
and the left LED indicator blinks in orange when data is transmitting /
receiving.
4
DC12V
12V DC power supply.
5
GND
Grounding
Note: The DS-6701HWI/HFI model provides no beeper.
DS-6704HWI/HFI:
Description of rear panel:
Item
Description
1
ALARM IN
Relay alarm input.
2
ALARM OUT
Relay alarm output.
3
RS-232
Serial interface for configuration of device’s parameters or used as transparent
channel.

Quick Operation Guide of DS-6700 Series Audio/Video Encoder
6
4
RS-485
RS-485 serial interface; connect to pan/tilt unit, speed dome, etc.
5
RESET
Restore the factory default settings by holding the RESET button for more than
15 seconds after the device is turned on.
6
microSD
microSD interface for data storage.
7
LAN
10M/100Mbps adaptive Ethernet interface (PoE).
The right LED indicator lights in green when the network cable is connected,
and the left LED indicator blinks in orange when data is transmitting /
receiving.
8
DC12V
12V DC power supply.
9
GND
Grounding
Note: The DS-6704HWI/HFI model provides no beeper.
DS-6708HWI/HFI (-SATA):
2
14 5 6 7 8 10
9
3
11
Note: DS-6701/6704 HWI-SATA and DS-6701/6704 HFI-SATA models provide 1/4 video input and 1/4 audio
input interfaces on the rear panel.
Description of rear panel:
Item
Description
1
VIDEO IN
BNC connectors for video input.
2
LINE IN
3.5mm two-way audio input interface; connect to active pick-up, microphone, etc.
3
AUDIO OUT
3.5mm audio output interface; connect to audio output device, e.g., loudspeaker,
etc.
4
AUDIO IN
Line input interface for audio input.
5
LAN
10M/100/1000Mbps adaptive Ethernet interface.
6
RESET
Restore the factory default settings by holding the RESET button for more than 15
seconds after the device is turned on.
7
RS-232, RS-485
RS-232 serial interface for configuration of device’s parameters or used as
transparent channel; RS-485 serial interface for connection to pan/tilt unit, speed
dome, etc.
8
ALARM IN
Relay alarm input.
9
ALARM OUT
Relay alarm output.
10
DC12V
12V DC power supply.
11
GND
Grounding

Quick Operation Guide of DS-6700 Series Audio/Video Encoder
7
DS-6716HWI/HFI (-SATA):
Description of rear panel:
Item
Description
1
VIDEO IN
BNC connectors for video input.
2
LINE IN
3.5mm two-way audio interface; connect to active pick-up, microphone, etc.
3
AUDIO OUT
3.5mm audio output interface; connect to audio output device, e.g., loudspeaker,
etc.
4
AUDIO IN
Line input interface for audio input.
5
LAN
10M/100/1000Mbps adaptive Ethernet interface.
6
RESET
Restore the factory default settings by holding the RESET button for more than 15
seconds after power is turned on.
7
RS-232, RS-485
RS-232 serial interface for configuration of device’s parameters or used as
transparent channel; RS-485 serial interface for connection to pan/tilt unit, speed
dome, etc.
8
ALARM IN
Relay alarm input.
9
ALARM OUT
Relay alarm output.
10
DC12V
12V DC power supply.
11
GND
Grounding

Quick Operation Guide of DS-6700 Series Audio/Video Encoder
8
Specifications
DS-6700HFI:
Model
DS-6701HFI
DS-6704HFI
DS-6708HFI
DS-6716HFI
Video/
Audio
input
Video
Compression
H.264/MPEG4/MPEG2/MJPEG
Video input
1-ch
4-ch
8-ch
16-ch
BNC (1.0 Vp-p, 75 Ω)
Audio
Compression
G.711u
Audio Input
1-ch
4-ch
8-ch
16-ch
1-ch, 3.5mm interface
(2.0 Vp-p, 1 kΩ)
(LINE IN)
Line input interface (2.0 Vp-p, 1 kΩ)
Two-way
audio input
1-ch, 3.5mm interface
(2.0 Vp-p, 1 kΩ)
(LINE IN)
1-ch, 3.5mm interface (2.0 Vp-p, 1 kΩ)
Video/
Audio
output
Audio
output
1-ch, 3.5mm interface (Linear, 600 Ω)
Recording
resolution
4CIF / 2CIF / CIF / QCIF
Frame rate
H.264/MPEG4/MPEG2 encoding: 25 fps (P) / 30 fps (N); MJPEG encoding: 15 fps
Video bit rate
32 Kbps ~ 3072 Kbps, or user defined (Max. 8192 Mbps)
Audio bit rate
64 Kbps
Dual Stream
Support
Stream Type
Video / Video & Audio
Data
storage
Type
NAS, iSCSI, IPSAN, microSD
NAS, iSCSI, IPSAN
Capacity
Up to 4 TB capacity for each disk, and 32G for microSD storage
External
interface
Network
interface
1 RJ-45 10 M / 100 Mbps adaptive Ethernet
interface (PoE)
1 RJ-45 10 M / 100 M /1000 Mbps adaptive
Ethernet interface
Protocols and
Service
IPv4/v6, HTTP, HTTPS, QoS layer3 DiffServ, FTP, SMTP, Bonjour, UPnPTM, Multicast,
SNMPv1/v2c/v3(MIB-II), DNS, DynDNS, HiDDNS, NTP, RTSP, RTP/RTCP,TCP, UDP,
IGMP, ICMP, DHCP, ARP, SOCKSv4/v5, PSIA, ONVIF, CGI, IEEE802.1X, netFilter
Serial
interface
1 half-duplex RS-485
interface
1 half-duplex RS-485 interface; 1 RS-232 interface
Alarm in
1
4
8
16
Alarm out
1
2
4
4
General
Power
supply
12 VDC
Power
Consumption
≤ 6W
≤ 8W
≤ 10W
≤ 22W
Working
temperature
-10°C ~ +55°C
Working
humidity
10% ~ 90%
Dimensions
(W ×D ×H)
80 ×90 ×39mm
114 ×128 ×48mm
315 ×200 ×45mm
440 ×274 ×45mm
Weight
≤ 0.5 Kg
≤ 1 Kg
≤ 2 Kg
≤ 4 Kg

Quick Operation Guide of DS-6700 Series Audio/Video Encoder
9
DS-6700HFI-SATA:
Model
DS-6701HFI-SATA
DS-6704HFI-SATA
DS-6708HFI-SATA
DS-6716HFI-SATA
Video/
Audio
input
Video
Compression
H.264/MPEG4/MPEG2/MJPEG
Video input
1-ch
4-ch
8-ch
16-ch
BNC (1.0 Vp-p, 75 Ω)
Audio
Compression
G.711u
Audio input
1-ch
4-ch
8-ch
16-ch
Line input interface (2.0 Vp-p, 1 kΩ)
Two-way audio
input
1-ch, 3.5mm interface (2.0 Vp-p, 1 kΩ)
Video/
Audio
output
Audio
output
1-ch, 3.5mm interface (Linear, 600 Ω)
Recording
resolution
4CIF / 2CIF / CIF / QCIF
Frame rate
H.264/MPEG4/MPEG2 encoding: 25 fps (P) / 30 fps (N); MJPEG encoding: 15 fps
Video bit rate
32 Kbps ~ 3072 Kbps, or user defined (Max. 8192 Mbps)
Audio bit rate
64 Kbps
Dual Stream
Support
Stream Type
Video / Video & Audio
Data
storage
Type
SATA, NAS, iSCSI, IPSAN
SATA
1 SATA interface
Capacity
Up to 4 TB capacity for each disk
External
interface
Network
interface
1 RJ-45 10 M / 100 M /1000 Mbps adaptive Ethernet interface
Protocols and
Service
IPv4/v6, HTTP, HTTPS, QoS layer3 DiffServ, FTP, SMTP, Bonjour, UPnPTM, Multicast,
SNMPv1/v2c/v3(MIB-II), DNS, DynDNS, HiDDNS, NTP, RTSP, RTP/RTCP,TCP, UDP,
IGMP, ICMP, DHCP, ARP, SOCKSv4/v5, PSIA, ONVIF, CGI, IEEE802.1X, netFilter
Serial
interface
1 half-duplex RS-485 interface; 1 RS-232 interface
Alarm in
8
8
8
16
Alarm out
4
General
Power supply
12 VDC
Power
consumption
(without HDD)
≤ 10W
≤ 22W
Working
temperature
-10°C ~ +55°C
Working
humidity
10% ~ 90%
Dimensions
(W ×D ×H)
315 ×200 ×45 mm
440 × 274 ×45 mm
Weight
(without HDD)
≤ 2 Kg
≤ 4 Kg