HIK VISION DS-KD3002-VM User manual

Residential Video Intercom Bundle
User Manual

Residential Video Intercom Bundle·User Manual
i
User Manual
© 2018 Hangzhou Hikvision Digital Technology Co., Ltd.
This user manual is intended for users of the residential video intercom bundle.
The bundle contains:
Series
Model
Door Station
DS-KD3002-VM
Video/Audio Distributor
DS-KAD312
Indoor Station
DS-KH3200-L
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This
manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by
any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are
registered trademarks or the subject of applications for the same by Hikvision and/or its
affiliates. Other trademarks mentioned in this manual are the properties of their
respective owners. No right of license is given to use such trademarks without express
permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.

Residential Video Intercom Bundle·User Manual
ii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable harmonized
European standards listed under the EMC Directive 2014/30/EU, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot
be disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated
collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point.
For more information see: www.recyclethis.info

Residential Video Intercom Bundle·User Manual
iii
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the device yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
The video/audio distributor and its power adaptor should be placed in a fire enclosure
cabinet.
Use a qualified power adaptor to provide power for the video/audio distributor. User
video/audio distributor to power the indoor station. The power that video/audio
distributor provided conforms to LPS.
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.

Residential Video Intercom Bundle·User Manual
iv
Do not place the device in extremely hot (refer to the specification of the device for
the detailed operating temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunction however), and affecting the endurance of
sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct contact
with the device cover, because the acidic sweat of the fingers may erode the surface
coating of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and
lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to
the instructions provided by the battery manufacturer.

Residential Video Intercom Bundle·User Manual
v
Table of Contents
1 Introduction .................................................................................................1
1.1 Overview.................................................................................................................. 1
1.2 Typical Application................................................................................................... 1
1.3 Bundle Wiring.......................................................................................................... 2
2 Appearance Description ............................................................................... 4
2.1 Indoor Station.......................................................................................................... 4
2.1.1 Front Panel........................................................................................................ 4
2.1.2 Rear Panel ......................................................................................................... 5
2.2 Door Station............................................................................................................. 6
2.3 Video/Audio Distributor .......................................................................................... 7
2.3.1 Front Panel/Back Panel ..................................................................................... 7
2.3.2 Side Panel.......................................................................................................... 8
3 Terminals and Wirings................................................................................ 10
3.1 Terminals ............................................................................................................... 10
3.1.1 Indoor Station Terminals ................................................................................. 10
3.1.2 Door Station Terminals.................................................................................... 11
3.1.3 Video/Audio Distributor Interfaces................................................................. 12
3.2 Wirings .................................................................................................................. 13
3.2.1 Indoor Station Wiring...................................................................................... 13
3.2.2 Door Station Wiring ........................................................................................ 14
Door Lock Wiring ..................................................................................................... 14
Door Magnetic Wiring ............................................................................................. 15
Exit Button Wiring.................................................................................................... 16
External Card Reader Wiring.................................................................................... 16
Alarm Device Input Wiring....................................................................................... 18
Alarm Device Output Wiring.................................................................................... 18
4 DIP Settings................................................................................................ 19
4.1 Configure RW 1...................................................................................................... 19
4.2 Configure RW 2...................................................................................................... 22
5 Installation ................................................................................................. 24
5.1 Indoor Station Installation ..................................................................................... 24
5.1.1 Installation Accessory Description................................................................... 24
5.1.2 Wall Mounting with Junction Box ................................................................... 24
5.2 Door Station Installation ........................................................................................ 26
5.2.1 Installation Accessory Description................................................................... 26
5.2.2 Wall Mounting with Gang Box......................................................................... 26
5.3 Video/Audio Distributor Installation ..................................................................... 28
6 Local Operation .......................................................................................... 30

Residential Video Intercom Bundle·User Manual
vi
6.1 Getting Started ...................................................................................................... 30
6.2 Initiate Video Intercom.......................................................................................... 30
6.3 Unlock the Door..................................................................................................... 30
Appendix ...................................................................................................... 31
Video/Audio Distributor Power Supply ....................................................................... 31
Door Station Power Supply.......................................................................................... 33

Residential Video Intercom Bundle·User Manual
1
1Introduction
1.1 Overview
The residential video intercom bundle is composed of and an indoor station, a door
station and a video/audio distributor. Featuring in the convenient installation and easy
operation, it is meanly applied in the buildings for improving the living security.
1.2 Typical Application
Figure 1-1 Typical Application
Configure the room number before build the system on the video/audio distributor.
See the 5 DIP Settings for detailed DIP rules.
The indoor station, door station and video/audio distributor are connected via
network cable transferring analog signal.
The door station, outer door station and master station should all connect to the
same LAN via network cable transferring digital signal.

2
1.3 Bundle Wiring
Figure 1-2 Bundle Wiring
See the appendix for the power supply connection of door station and video/audio
distributor.
Connect LAN2 of door station to the bus input on the video/audio distributor via
network cable.
Before configure the device, set Digit 8 (RW1) as ON to adapt to the current indoor
station version.

3
2

4
3Appearance Description
3.1 Indoor Station
3.1.1 Front Panel
Figure 3-1 Front Panel
Table 3-1 Components Description
No.
Description
1
Volume Wheel
2
Power Supply Indicator
3
Alarm Indicator
4
Answer/Decline Key
5
Unlock Key
6
Live View Key
7
Management Center Key
8
LCD Display Screen
9
Microphone
10
Arm/Disarm Key
The Unlock key is valid only when does the indoor station speak with the door station
or open the live view of the door station.

5
3.1.2 Rear Panel
Figure 3-2 Rear Panel
Table 3-2 Components Description
No.
Description
1
Network Interface(24 VDC)
2
Reserved
3
Loudspeaker
4
Terminals

6
3.2 Door Station
Figure 3-3 Front View
Figure 3-4 Rear View
Table 3-3 Components Description
No.
Description
1
Low Illumination Supplement Light
2
Built-in Camera
3
Loudspeaker
4
LCD Display Screen
5
Card Induction Area
6
Keypad
7
Call Button
8
Call Center Key
9
Microphone

7
No.
Description
10
TAMPER
3.3 Video/Audio Distributor
3.3.1 Front Panel/Back Panel
Figure 3-5 Front Panel
Figure 3-6 Back Panel
Table 3-4 Components Description
No.
Description
1
Signal Indicator
2
Power Indicator

8
3.3.2 Side Panel
Figure 3-7 DS-KAD312 Side Panel 1
Figure 3-8 DS-KAD312 Side Panel 2
Figure 3-9 DS-KAD312 Side Panel 3
Table 3-5 Components Description
No.
Description
1
Power Socket

9
2
Network Interface
3
DIP Switch
4
Serial Port

10
4Terminals and Wirings
4.1 Terminals
4.1.1 Indoor Station Terminals
Figure 4-1 Terminals of DS-KH3200-L
Table 4-1 Descriptions of Terminals and Interfaces
No.
Description
G
Grounding
Z1
Zone Detector Input Terminal 1(Smoke Detector)
Z2
Zone Detector Input Terminal 2(Gas Detector)
Z3
Zone Detector Input Terminal 3(Door Magnetic)
Z4
Zone Detector Input Terminal 4(Active Infrared)
G
Grounding

11
4.1.2 Door Station Terminals
Figure 4-2 Terminals and Interfaces of DS-KD3002-VM
Table 4-2 Descriptions of Terminals and Interfaces
Name
No.
Interface
Description
USB
1
USB
USB Interface
LAN
2
LAN1
Network Interface
3
LAN2
Analog Interface
Power
Supply
4
DC 12V
DC 12V Power Supply Input
READER
A1
12V
Power Supply Output
A2
GND
Grounding
A3
W1
Data Input Interface Wiegand Card Reader:
Data1
A4
W0
Data Input Interface Wiegand Card Reader:
Data0
A5
BZ
Card Reader Buzzer Output
A6
ERR
Card Reader Indicator Output (Invalid Card
Output)
A7
OK
Card Reader Indicator Output (Valid Card
Output)
A8
TAMP
Tamper-proof Input of Wiegand Card Reader
ALARM
B1
AO2-
Alarm Relay Output 2

12
Name
No.
Interface
Description
OUT
B2
AO2+
B3
AO1-
Alarm Relay Output 1
B4
AO1+
DEBUG
B5
GND
Grounding
B6
RX
Serial Port Debugging/Receive data
B7
TX
Serial Port Debugging/Send data
B8
3.3V
Serial Port Debugging/Power Supply
DOOR
C1
12V
Power Supply Output
C2
GND
Grounding
C3
NC2
Door Lock Relay Output (NC)
C4
COM2
Grounding Signal
C5
NO2
Door Lock Relay Output (NO)
C6
NC1
Door Lock Relay Output (NC)
C7
COM1
Grounding Signal
C8
NO1
Door Lock Relay Output (NO)
RS485
D1
GND
RS-485 Communication Interfaces
D2
485-
D3
485+
ALARM IN
D4
GND
Grounding Signal
D5
AI4
Alarm Input 4
D6
AI3
Alarm Input 3
D7
AI2
Alarm Input 2
D8
AI1
Alarm Input 1
4.1.3 Video/Audio Distributor Interfaces

13
Figure 4-3 Network Interfaces of DS-KAD312
Table 4-3 Descriptions of Interfaces
No.
Description
No.
Description
1
Decoding Output Interface 1
8
Decoding Output Interface 8
2
Decoding Output Interface 2
9
Decoding Output Interface 9
3
Decoding Output Interface 3
10
Decoding Output Interface 10
4
Decoding Output Interface 4
11
Decoding Output Interface 11
5
Decoding Output Interface 5
12
Decoding Output Interface 12
6
Decoding Output Interface 6
13
Bus Output Interface
7
Decoding Output Interface 7
14
Bus Input Interface
Interface (No.1 to 12) can provide power (24 VDC) for indoor station. It cannot
connect to other device directly.
Interface (No.13) is the bus output interface. It supports connect signal-amplifier or
other video audio distributor.
Interface (No.14) is the bus input interface. It supports video and audio input and
audio output, and connects to door station and other video audio distributor.
4.2 Wirings
4.2.1 Indoor Station Wiring
There are 6 pins in the terminal on the rear panel of the indoor station: 2 GND pins and
4 alarm input pins.
To access the alarm input device, refer to Figure 4-4.