HIK VISION 4 Inch High Speed Dome User manual

4-inch High Speed Dome
User Manual
V1.0.0
Hikvision Digital Technology Co., Ltd.
http://www.hikvision.com

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
1
Thank you for purchasing our product. If there is any question or request, please do not hesitate to
contact the dealer.
This manual is applicable to 4-inch High Speed Dome.
This manual may contain several technically inaccurate points or printing errors, and the content is
subject to change without notice. The updates will be added into the new version of this manual.
We will readily improve or update the products or procedures described in the manual.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For
more information see: www.recyclethis.info.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
3
Safety Warnings and Cautions
Please pay attention to the following warnings and cautions:
Hazardous Voltage may be present: Special measures and precautions must be
taken when using this device. Some potentials (voltages) on the device may
present a hazard to the user. This device should only be used by employees from
our company with knowledge and training in working with these types of devices
that contain live circuits.
Power Supply Hazardous Voltage: AC mains voltages are present within the power supply assembly.
This device must be connected to a UL approved, completely enclosed power supply, of the proper
rated voltage and current. No user serviceable parts inside the power supply.
System Grounding (Earthing): To avoid shock, ensure that all AC wiring is not exposed and that the
earth grounding is maintained. Ensure that any equipment to which this device will be attached is
also connected to properly wired grounded receptacles and are approved medical devices.
Power Connect and Disconnect:The AC power supply cord is the main disconnect
device to mains (AC power).The socket outlet shall be installed near the equipment
and shall be readily accessible.
Installation and Maintenance:Do not connect/disconnect any cables to or perform
installation/maintenance on this device during an electrical storm.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
4
Power Cord Requirements: The connector that plugs into the wall outlet must be a grounding-type
male plug designed for use in your region. It must have certification marks showing certification by
an agency in your region. The connector that plugs into the AC receptacle on the power supply must
be an IEC 320, sheet C13, female connector. See the following website for more information
http://kropla.com/electric2.htm.
Lithium Battery: This device contains a Lithium Battery. There is a risk of
explosion if the battery is replaced by an incorrect type. Dispose of used
batteries according to the vendor’s instructions and in accordance with local
environmental regulations.
Perchlorate Material: Special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. This notice is required by California Code of
Regulations, Title 22, Division 4.5, Chapter 33: Best Management Practices for Perchlorate Materials.
This device includes a battery which contains perchlorate material.
Taiwan battery recycling:
Please recycle batteries.
Thermal and Mechanical Injury:Some components such as heat sinks, power
regulators, and processors may be hot; care should be taken to avoid contact
with these components.
Electro Magnetic Interference:This equipment has not been tested for
compliance with emissions limits of FCC and similar international regulations. This device is not, and
may not be, offered for sale or lease, or sold, or leased until authorization from the United States
FCC or its equivalent in other countries has been obtained. Use of this equipment in a residential
location is prohibited. This equipment generates, uses and can radiate radio frequency energy which
may result in harmful interference to radio communications. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment on
and off, the user is required to take measures to eliminate the interference or discontinue the use of
this equipment.
Lead Content:
Please recycle this device in a responsible manner. Refer to local
environmental regulations for proper recycling; do not dispose of device in
unsorted municipal waste.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
5
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or
property loss. The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings:
Follow these safeguards to prevent
serious injury or death.
Cautions:
Follow these precautions to
prevent potential injury or
material damage.
Warnings
In the use of the product, you must be strict compliance with the electrical safety regulations of
the nation and region.
Please use the power adapter, which is provided by normal company. The standard of the power
adapter is AC24V/2A.
Do not connect several devices to one power adapter as adapter overload may cause over-heat
or fire hazard.
Please make sure that the plug is firmly connected on the power socket.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or places
subject to shock (ignorance can cause equipment damage).
Do not place the dome in extremely hot, cold (the operating temperature shall be -30°C ~ +65°C),
dusty or damp locations, or fire or electrical shock will occur otherwise.
The dome cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or
radiator is forbidden (ignorance can cause fire danger).
Do not aim the camera at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfunction however), and affecting the endurance of CCD at the
same time.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
6
Please use the provided glove when open up the dome cover, avoid direct contact with the
dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome
cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, do not
use alkaline detergents.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
7
Table of Contents
Chapter 1 Overview.......................................................................................................................................1
1.1 Description ...................................................................................................................................................................1
1.2 Functions ......................................................................................................................................................................1
Chapter 2 Getting Started ..............................................................................................................................5
2.1 Power-up Action...........................................................................................................................................................5
2.2 Basic Operations ..........................................................................................................................................................5
2.3 System-defined Presets ...............................................................................................................................................6
2.4 On Screen Displays.......................................................................................................................................................7
Chapter 3 Menu Operation ............................................................................................................................8
3.1 Accessing and Operating the Menu............................................................................................................................9
3.2 Configuring System Information...............................................................................................................................10
3.2.1 Checking System Information ...............................................................................................................................10
3.2.2 Configuring System Parameters............................................................................................................................10
3.3 Configuring Image Parameters..................................................................................................................................13
3.3.1 Configuring Camera Parameters...........................................................................................................................13
3.3.2 Configuring Privacy Mask......................................................................................................................................17
3.3.3 Configuring OSD Settings ......................................................................................................................................18
3.4 Configuring PTZ Control Parameters ........................................................................................................................20
3.4.1 Configuring PTZ Parameters .................................................................................................................................20
3.4.2 Configuring Presets................................................................................................................................................22
3.4.3 Configuring Patrols ................................................................................................................................................24
3.4.4 Configuring Patterns..............................................................................................................................................25
3.4.5 Configuring Time Tasks .........................................................................................................................................27
3.4.6 Configuring Zones..................................................................................................................................................29
3.4.7 Clearing PTZ Control Settings................................................................................................................................30
3.5 Configuring and Handling Alarms.............................................................................................................................31
3.5.1 Configuring Alarm Input and Linked Actions .......................................................................................................31
3.5.2 Configuring Alarm Parameters .............................................................................................................................32
3.5.3 Configuring Auxiliary Alarm Output .....................................................................................................................33
3.6 Others .........................................................................................................................................................................33
3.6.1 Line Synchronization .............................................................................................................................................33
3.6.2 Setting the language of the menu ........................................................................................................................34
3.6.3 Configuring Dome Authentication .......................................................................................................................34
3.6.4 Restoring Default Dome Settings..........................................................................................................................35
3.6.5 Restoring Default Camera Settings.......................................................................................................................36
3.6.6 Rebooting the Dome .............................................................................................................................................36
Appendix ........................................................................................................................................................... 37
Appendix 1 Lightning & Surge Protection .............................................................................................................................37
Appendix 2 RS485 Bus Connection........................................................................................................................................38

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
8
Appendix 3 24VAC Wire Gauge & Transmission Distance....................................................................................................40
Appendix 4 Table of Wire Gauge Standards..........................................................................................................................41

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
1
Chapter 1 Overview
1.1 Description
Integrated with the built-in pan/tilt unit, the high speed dome features highly sensitive response
and reliable performance. The speed dome can be adopted in various surveillance fields with its
full-integral functions and features, such as corridor, large venue, meeting room, station, community,
etc.
Figure 1-1 Appearance
1.2 Functions
OSD (On Screen Display)
The on-screen display is an image superimposed on a screen picture, used for displaying
information and menu.
Self-adaptive Protocol
The speed dome is compatible with PELCO-D, PELCO-P, PRIVATE-Code, VICON and KALATEL-312
protocol, etc., and is capable of being self-adaptive to these protocols without selecting protocol by
DIP switch settings.
Keyboard Control
The pan/tilt movement and zoom actions of dome can be controlled by the control keyboard, DVR,
matrix, etc.
Limit Stops
The dome can be programmed to move within the limit stops (left/right, up/down) which are
configurable by the control keyboard, DVR or client application software.
Auto Scan
The dome provides 5 scanning modes: pan scanning, tilt scanning, frame scanning, random scanning

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
2
and panorama scanning. The scanning speed can be set by OSD menu from level 1 to 40, with the
corresponding speed ranging from 1°/second to 40°/second.
Preset Freeze Frame
This feature freezes the scene on the monitor when going to a preset. This allows for smooth
transition from one preset scene to another and also guarantees that masked area will not be
revealed when going to a preset.
Presets
Each of the user-definable presets can be programmed to use pan, tilt, camera settings and other
settings. When preset is called, the dome will automatically move to the defined position. User is
allowed to add, modify, delete and call each preset.
Label Display
The on-screen label of the preset title, azimuth/elevation, zoom and other operations can be
programmed by menu and displayed on the monitor.
Auto Flip
In manual tracking mode, when a target object goes directly beneath the dome, the dome will
automatically rotate 90 degrees in horizontal direction to maintain continuity of tracking.
Privacy Mask
The privacy mask allows a user to program user-defined areas that cannot be viewed by the
operator of the dome system. A masked area will move with pan and tilt functions and
automatically adjust in size as the lens zooms telephoto and wide.
3D Intelligent Positioning
The speed dome can be controlled with the 2 buttons and scroll of mouse can be used under
PRIVATE-Code protocols with devices and client software. Click on a certain area and the device will
move to the scene with corresponding point as the center. When a rectangular area is selected by
left-clicking the mouse, device will move to its center and enlarge it. With right-clicking, the lens will
zoom in, and the scroll can easily make the lens zooming, and mouse operation automatically
incorporates zooming effect.
Proportional Pan
Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the
amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given
amount of joystick deflection than at wide zoom settings. This keeps the image from moving too fast
on the monitor when there is a large amount of zoom.
Auto Focus
The auto focus enables the camera to focus automatically to maintain clear video images.
DAY/NIGHT Auto-switch
The speed dome delivers color images during the day; as light diminishes at night, it switches to
night mode and delivers black and white images with high quality. You can also switch it to NIGHT
mode manually to increase the sensitivity in low light conditions.
Slow Shutter
Slow shutter is the function of extending the exposure time to accumulate more light when the light
condition is low. Thus, the image can be brighter.
Backlight Compensation (BLC)
If the speed dome focuses on an object against strong backlight, the object will be too dark to be
seen clearly. The BLC function can compensate light to the object in the front to make it clear, but

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
3
this causes the over-exposure of the background where the light is strong.
Wide Dynamic Range (WDR)
The wide dynamic range function helps the speed dome provide clear images even under back light
circumstances. When there are both very bright and very dark areas simultaneously in the field of
view, WDR balances the brightness level of the whole image and provide clear images with details.
White Balance
White balance is the white rendition function of the speed dome to adjust the color temperature
according to the environment automatically. It can remove the unrealistic color casts in the image.
Patrol
The high speed dome provides up to 8 patrols. In each patrol, user is allowed to specify the scanning
track by a group of user-defined presets, with the scanning speed between two presets and the
dwell time at the preset separately programmable.
Pattern
A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that can be
recalled with a command from a controller or automatically by a configured function (alarm, park,
time task, or power-up). By default the focus and iris are in auto status during the preset is being
memorized.
Power-off Memory
This feature allows the dome to resume its previous position or status after power is restored. By
default setting, the dome supports the power-off memory capability with the dwell time of 3
minutes.
Alarm Response Action
The speed dome supports 2 alarm inputs which can be set to NO or NC. Upon having received the
alarm input signal, the dome will automatically activate a user-defined action, which can be
programmed to: preset 1-8, pattern 1-4, patrol 1-8, pan scan, tilt scan, random scan, frame scan,
panoramic scan, color or B&W mode. After the alarm is cleared, the dome is capable of resuming its
previous activity or position.
AUX Output
An auxiliary output is a configurable signal from the dome back box that can trigger another device
to operate. The dome provides one auxiliary output. The auxiliary output type can be set to NO
(normally open) or NC (normally closed). And the alarm dwell time is configurable as well.
Manchester Code Self-test
The speed dome supports Manchester code self-test for fault diagnostic. You can enable the
Manchester code diagnosis function by setting the positions 8 and 9 of DIP Switch to ON. The
corresponding fault code will be displayed on the screen (not available during park time) while
adopting Manchester protocol.
Table 1-1 Descriptions of the Fault Code
Fault Code
Description
E0
Normal control
E1
Cable is disconnected
E2
Cable is connected and data can be normally
received, but the address setting is incorrect
E3
Cable is connected and data can be normally
received, but the command setting is incorrect

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
4
E4
Cable is connected and data can be normally
received, but the settings of address and
command are incorrect
E5
Cable is connected, but the received data does
not comply with the requirements of Manchester
code
Time Task
A time task is a preconfigured action that can be performed automatically at a specific date and
time. The programmable actions include: preset 1-8, pattern 1-4, patrol 1-4, pan scan, tilt scan,
random scan, frame scan, panorama scan, day/night mode or none.
Zone
A zone is a user-defined area. The dome provides eight zones, each with configurable label. If the
dome has dwelled at a zone without receiving any command over 4 minutes, this feature will enable
the dome to perform panorama scan within the zone.
Password
The dome features password protection to prevent unauthorized changes to the dome settings.
Camera Title
Title text is the label used to identify the camera viewed on the monitor. Up to 15 characters can be
used for a title
RS-485 Failure Diagnostics
In the presence of failure at the transmitting and receiving terminals of RS-485 communications, the
speed dome is capable of performing self-test and detecting the fault results which will be displayed
on the screen.
Soft Baudrate
The baudrate of dome can be configured by the menu without need of DIP switch settings.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
5
Chapter 2 Getting Started
2.1 Power-up Action
After the power is applied, the speed dome will perform a series of self-test actions. It performs lens
actions firstly, then the panning movement and the tilting movement at last. After the power-up
self-test actions, the system information will be displayed for 2 minutes on the live view screen as
shown below.
TYPE DS- 2XX1-XXX
SN 000000000
ADDRESS 0
COM FORMAT 2400,8,1
PROTOCOL ADAPTIVE
VERSION 0. 00
HARDVERSI 0. 00
BUILD DATE 12 05 17
Figure 2-1 System Information
Table 2-1 Descriptions of the System Information
System Info
Description
TYPE
The model of the speed dome.
SN
The serial number of the speed dome.
ADDRESS
The default communication address of the speed dome.
COM Format
The communication settings of the speed dome. Baudrate (4 digits),
data bit (1 digit) and stop bit (1 digit).
PROTOCOL
It is for communicating with other devices.
VERSION
The version of the firmware.
HARDVERSI
The version of the hardware.
BUILD DATE
The date when the program of the software is compiled.
Note: You have to configure a protocol, an address and a baudrate for the dome the same as it in
the other devices.
2.2 Basic Operations
You can operate the speed dome using a control device. The control devices include the control

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
6
keyboards, DVRs, DVSs, etc. In this and the following chapters, operation of the speed dome by the
IE browser of a DVR will be taken as an example.
Note: Please make sure that the baudrate, date bit and address have been configured to the same
as those of the speed dome in the remote configuration interface of the control device. Please refer
to Table 2-1 for details of the configuration.
Panning and tilting:
Click the direction buttons to control the movement of the speed dome.
Zooming:
Click the ZOOM in/out buttons to control the zooming.
Focusing:
Click the FOCUS+ and FOCUS- buttons to adjust the focus.
Iris:
Click the IRIS+ and IRIS- buttons to adjust the iris.
2.3 System-defined Presets
Purpose:
The section lists the system-defined presets with special functions. These presets cannot be edited
but only called through a control device e.g. a DVS or web browser. To call the system-defined
presets remotely, you can choose the preset number from the list in the PTZ control panel. Please
refer to below table for details.
For instance, preset 99 is the “Start auto scan”. If you call the preset 99, the speed dome starts auto
scan function.
Table 2-2 System-defined Presets
Preset NO.
Function
Preset NO.
Function
33
Auto-flip
93
Set manual limit stops
34
Return to home position
94
Remote reboot
35
Patrol 1
95
Access main menu
36
Patrol 2
96
Stop scanning
37
Patrol 3
97
Start random scanning
38
Patrol 4
98
Start frame scanning
39
IR cut filter in
99
Start auto scanning
40
IR cut filter out
100
Start tilt scanning
41
Pattern 1
101
Start panorama scanning
42
Pattern 2
102
Patrol 5
43
Pattern 3
103
Patrol 6
44
Pattern 4
104
Patrol 7
92
Enable limit stops
105
Patrol 8
Note: For Manchester code control protocol, the system-defined presets with special functions are
shown as below:

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
7
Table 2-3 System-defined Presets of Manchester Code Control Protocol
Preset
NO.
Function
Preset
NO.
Function
65
Remote reboot
67
Auto-flip
66
Access main menu
70
Call Pattern 1
69
Stop programming pattern
71
Call Pattern 2
70
Set Pattern 1
72
Call Pattern 3
71
Set Pattern 2
72
Set Pattern 3
2.4 On Screen Displays
The speed dome supports following on screen displays:
Zoom: Identifies the amount of magnification. The format is ZXXX. XXX is the zoom amount.
Direction: Displays panning and tilting direction, with the format of NEXXX TXXX. The XXX following
NE indicates the degrees in north east direction, while the XXX following T indicates the degrees in
tilt position.
Time: Supports for time display.
Preset Title: Identifies preset being called.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
8
Chapter 3 Menu Operation
The OSD menu tree is shown in the following figure.
Note: The menu varies depending on the model of speed dome.
MAIN MENUS
SYS INFO DOME
SETTINGS RESTORE DEFAULTS RESTORE CAMERA
SYS INFO
SETTINS
CAMERA
PARAMETER
MOTION
PARAMETER
PRESETS
PATROLS
TIME TASK
PATTERNS
PRIVACYS
ALARMS
AUXS
CLEAR
SETTINGS
FOCUS
ZOOM LIMIT
ZOOM SPEED
SLOW
SHUTTER
AUTO FLIP
PROPORTION
AL PAN
PARK ACT
SCAN SPEED
IMAGE
FREEZE
DOME SPEED
PRESET PEED
LIMIT STOP
PARK TIME
REBOOT DOME
LANGUAGE
SET TITLE
ADDRESS
COM FORMAT
PROTOCOL
TEMPERATUR
E
BUILD DATE
VERSION
TYPE
PASSWORD
ZONES
LINE SYNC
CLEAR STOPS
<SETTING
STOPS>
D/N LEVEL
SHARPNESS
EXPOSURE
COMP
IMAGE FLIP
WHITE
BALANCE
GAIN LIMIT
BLC/WDR
BLC LEVEL
IRCUT
FILTER
AE MODE
IRIS
SHUTTER
GAIN
RED
BLUE
FOCUS LIMIT
INIT LENS
NOISE
REDUCE
WIDE LIMIT
CHROMA
SUPPRESS
SATURATION
CONTRAST
HLC
HR MODE

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
9
Before you start:
You can operate the speed dome using the on-screen display menu remotely by connecting to a
DVR or a DVS (encoder).
Examples of entering speed dome menu are listed as follows:
Enter the menu by pressing buttons: PTZ -> REC -> 9-> 5on the front panel of the DVR.
Enter the menu by pressing buttons: CALL -> 9-> 5-> ENTER on the keyboard.
Enter the menu via the IE browser of a DVR/DVS.
Menu operations via the IE browser of a DVR will be taken as an example in this chapter.
3.1 Accessing and Operating the Menu
To enter the main menu:
Steps:
1. Connect the video and RS-485 cables of speed dome to a DVR.
2. Visit the DVR with the IE browser.
3. View the live video of the speed dome.
4. Call preset 95 from the preset list in the PTZ control panel of the DVR.
MAIN MENUS
<SYS INFO>
<DOME SETTINGS>
<RSTORE DEFAULTS>
<RSTORE CAMERA>
<RSBOOT DOME>
LANGUAGE ENGLISH
SET TITLE OFF
EXIT
Figure 3-1 Main Menu
To move the cursor and operate the menu:
Move the cursor up/down: On control panel of the live view interface of the DVR, click up and
down direction buttons or FOCUS+ and FOCUS- buttons to move the cursor in the menu up and
down.
Enter / Exit: On control panel of the live view interface of the DVR, click IRIS+ to enter a
submenu; move the cursor to BACK in the menu and click IRIS+ to return to the previous menu;
move the cursor to EXIT in the menu and click IRIS+ to exit the main menu.
Page up / page down: There is no “RETURN”or “NEXT”menu items for turning page up or
down. On control panel of the live view interface of the DVR, you can click left and right
direction buttons to turn page up or down.
To change the value of a parameter:
Steps:

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
10
1. Move the cursor to the target item and click IRIS+ button and you can see the cursor (diamond
mark) will change to be totally hollow.
2. Click the up/down or left/right buttons in the PTZ control panel to choose the value from the
selectable value list.
3. Press IRIS+ to confirm the change or click IRIS- to cancel and restore the original value. The
diamond mark will change back to be stuffed or half stuffed.
3.2 Configuring System Information
3.2.1 Checking System Information
Purpose:
System information menu displays the current system information of the speed dome as shown in
Figure 3-2, including model, address, protocol, etc. The information shown on this submenu is
similar to the system information shown after the power-up action. Please refer to Section 2.1 for
more details.
Enter the system information display menu:
MAIN MENUS > SYS INFO
SYS INFO
TYPE DS- 0XX0-000
ADDRESS 0
COM FORMAT 0000,0,0
PROTOCOL XXXXX
VERSION 0. 00
HARDVERSION 0. 00
BUILD DATE 12 08 09
BACK EXIT
Figure 3-2 System Information
Notes:
Information in this interface cannot be edited.
The temperature refers to the internal temperature of the speed dome.
3.2.2 Configuring System Parameters
Purpose:
You can check and also edit the system information of software address, baudrate, system time, etc.
on the system information settings menu.

User Manual of 4-inch High Speed Dome
© Hikvision Digital Technology Co., Ltd. All Rights Reserved.
11
Enter the system information settings menu:
MAIN MENUS > DOME SETTINGS > SYS INFO SETTINGS
SYS INFO SETTINGS
SOFT ADDRESS 1
SOFT ADDR ACTIVE OFF
SOFT BAUD 2400
SOFT BAUD ACTIVE OFF
BROADCAST ADDRESS ON
PELCO CHECKSUM ON
SYS TIME
BACK EXIT
SYS INFO SETTINGS
ZERO ANGLE
DISPLAY SETTINGS
FAN CONTROL N/A
EIS FUNCTION ON
EIS LEVEL 2
PRESET DFOCUS OFF
PROTOCOL STATUS SET OFF
BACK EXIT
SYS INFO SETTINGS
PROTOCOL SET AUTO MATCH
485CHECK SET AUTO
BACK EXIT
Figure 3-3 System Information Settings
Note: You can click the left and right direction buttons in the PTZ control panel via the IE browser of
the DVR for page up or page down if more than one page is available.
Descriptions of system parameter configuration:
Dome address settings
Task 1: Set the soft address of the speed dome.
If the SOFT ADDR ACTIVE is set as ON, the soft address is the valid address for connecting the
speed dome. The SOFT ADDRESS ranges from 1 to 255;
If the SOFT ADDR ACTIVE is set as OFF, the hard address set by the DIP switch is the valid
address of the speed dome.
Task 2: Set the broadcast address of the speed dome.
When the BROADCAST ADDRESS is set to ON, the control devices with address 0 can control the
speed dome remotely regardless of the address of the speed dome.
With this function on, the control device with address 0 is capable of controlling all domes
connected to it. This function is usually for debugging.
Soft baudrate settings
If the SOFT BAUD ACTIVE is set as ON, the soft baudrate is the valid baudrate for the speed dome,
with 2400, 4800, 9600 and 19200 selectable.
If the SOFT BAUD ACTIVE is set as OFF, the baudrate should be set by the DIP switch.
Note: After you enable/disable the soft baudrate, the speed dome will reboot automatically to
activate the settings.
PELCO checksum
If the speed dome uses PELCO-P or PELCO-D protocol, you can set the PELCO CHECKSUM as ON for
improving the controlling effect.
System time configuration
Steps:
(1) Move the cursor to SYSTEM TIME using the direction buttons and click IRIS+ to enter.
(2) Click the left/right direction buttons to position the cursor on the specific item