HIK VISION DS-2CD886BF-E User manual

Quick Guide of Network Box Camera
1
Network Box Camera
Quick Guide
V3.0.0
Hangzhou Hikvision Digital Technology Co., Ltd.
http://www.hikvision.com
2010-04

Quick Guide of Network Box Camera
1
1.Camera Description
1.1 Side Panel Description
Serial NO.
Description
1
Lens mount
2
Bracket mounting holes, used to fix the camera to the bracket
3
Auto iris interface

Quick Guide of Network Box Camera
2
1.2 Rear Panel Description
Rear Panel of DS-2CD886BF-E and DS-2CD876BF:
Serial NO.
Description
1
F1+ F1-, F2+ F2- , F3+ F3-: Alarm output interface
2
T1, T2, T3, T4, GND: Alarm input interface
3
D+,D-: RS-485 interface
4
10M / 100M self-adaptive Ethernet interface
5
Video output interface
6
RESET: Reset all parameters to factory default settings
7
TXD , RXD,GND: RS-232 interface
8
Power supply
9
Power LED indicator, which turns red when power is applied to the unit
10
SD card slot
11
Audio input interface
12
Audio output interface
13
Ground
NOTE:
When the camera is power up, press the ‘RESET’ button for about 10 seconds, then all parameters,
including user name, password, IP address, port number, etc., will be reset to the factory default
settings.

Quick Guide of Network Box Camera
3
Rear Panel of DS-2CD886MF-E and DS-2CD876MF:
Serial NO.
Description
1
ALARM OUT, GND: Alarm output interface
ALARM IN, GND: Alarm input interface
2
D+, D-: RS-485 interface
3
TXD , RXD,GND: RS-232 interface
4
HDMI interface
5
RESET: Reset all parameters to factory default settings
6
10M / 100M self-adaptive Ethernet interface
7
Power supply
8
Power LED indicator, which turns red when power is applied to the unit
9
SD card slot
10
Audio input interface
11
Audio output interface
12
Ground
NOTE:
When the camera is power up, press the ‘RESET’ button for about 10 seconds, then all parameters,
including user name, password, IP address, port number, etc., will be reset to the factory default
settings.

Quick Guide of Network Box Camera
4
2.Installation
Box camera can be fixed in both wall and ceiling, the following section introduces the ceiling
mounting, and the wall mounting follows the same way:
Step 1: Fix the camera mounting bracket to the ceiling.
Fig 2.1 Fix camera mounting bracket
NOTE:
If it is wall, you need to fix the expand bolt (note: the mounting hole of the expand bolt should align
with the bracket) before fixing the bracket as ①in Fig 2.1 . If the wall surface is wooden, the part of
①in Fig 2.1 can be ignored and you can use the self-tapping screw to directly fix the bracket. Please
note that the wall on which the camera is fixed should be able to bear at least three times the
weight of the bracket and the camera.
Step 2: Screw the mounting hole to the mounting bracket, and then adjust the camera to the
desired monitoring location and finally tighten the knob on bracket to secure the camera to the
ceiling.

Quick Guide of Network Box Camera
5
Fig 2.2 Fix the Camera
Step 3: Mount the camera lens: connect the VIDEO OUT interface of the camera to the debugging
monitor, and adjust lens focus until you have obtained the clearest video images on the monitor,
and then lock the lens. If required, loosen the knob on the mounting bracket and adjust the camera
lens to the desired monitoring scene, and finally tighten the knob on bracket.
Fig 2.3 Mount and adjust Lens

Quick Guide of Network Box Camera
6
3.Search and Modify IP
SADP (Search Active Devices Protocol) software can automatically search the IP address of network
cameras’ on the same network with connection diagram as follows:
The operation of searching and modifying IP address is described as following:
2. Search IP address.
Click it Show the IP address of the camera
3. Modify IP address.
1. Install the SADP software , and then run the
“sadpdlg.exe”

Quick Guide of Network Box Camera
7
1. Click [modify]
2. Input new IP address and the
password ( Default: 12345) of
the camera, then click [save]
3. Modify successfully

Quick Guide of Network Box Camera
8
4.Preview via IE browser
Note:
The default IP of network cameras’ is ‘192.0.0.64’ with ‘admin’ as the administrator, ‘12345’ as
the password, and ‘8000’ as the default port.
For monitoring camera images, a comptuer running the Microsoft Windows Operating System and
Internet Explorer (Version 6.0 or later) are required. In this manual, we take Windows XP and IE 6.0
for example.
This chapter describes how to view the video from the camera via web browser, and operate as
following:
1. Open the IE browser, set the security level to [Medium] in
*Tools/InternetOptions/Security/Custom Level…+

Quick Guide of Network Box Camera
9
2. Type the IP address of the camera and press [Enter], and
then click the mention box that pop up.
3. Click [Run] to install the ActiveX control.