HIK VISION DS-K1T341BMWI-T User manual

©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images and all
other information hereinafter are for description and explanation only. The information contained in the
Manual is subject to change, without notice, due to rmware updates or other reasons. Please nd the
latest version of this Manual at the Hikvision Website (https://www.hikvision.com/).
Please use this Manual with the guidance and assistance of professionals trained in supporting the
Product.
Trademarks
and other Hikvision trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED“AS IS”AND“ WITH ALL
FAULTS AND ERRORS.”HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE
USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION
OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT,TORT
(INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE
PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND
HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE
OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR
OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF
REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY
RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU
ARE RESPONSIBLE FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS
OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY
RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR
ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS
DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY
ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE,
OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER
PREVAILS.
Data Protection
During the use of device, personal data will be collected, stored, and processed. To protect data, the
development of Hikvision devices incorporates privacy by design principles. For example, for devices
with identity authentication features, biometrics data is stored in your device with encryption method;
for ngerprint device, only ngerprint template will be saved, which is impossible to reconstruct a
ngerprint image.
As data controller, you are advised to collect, store, process, and transfer data in accordance with the
applicable data protection laws and regulations, including without limitation, conducting security
controls to safeguard personal data such as implementing reasonable administrative and physical
security controls and conduct periodic reviews and assessments of the eectiveness of your security
controls.
Visit the Hikvision Website at www.hikvision.com to download the user manual for detailed information.
1. Appearance
3.1 Wire Normal Device
2. Installation
DS-K1T341BMWI-T
Touchless Identity
Authentication Terminal
Quick Start Guide
Diagnostic Disclaimer
U.S. Disclaimer: Hikvision Highly Accurate Thermographic Cameras and Terminals (HAT Cameras and
Terminals) are not FDA-cleared or approved. The HAT Cameras and Terminals shall not be solely or
primarily used as an eective diagnostic device for COVID-19. Elevated body temperature should be
conrmed with secondary evaluation methods (e.g., an NCIT or clinical grade contact thermometer).
Users, through their experience with the Hikvision HAT Cameras and Terminals in the particular
environment of use, should determine the signicance of any fever or elevated temperature based on
the skin telethermographic temperature measurement. Visible thermal patterns are intended only for
locating the points from which to extract the thermal measurement.
To ensure the accuracy of the human skin-surface temperature measurement, the technology shall be
used to measure only one subject’s temperature at a time and shall not be used to measure multiple
individuals’temperatures simultaneously.
Canada Disclaimer: Hikvision Elevated Skin Temperature Cameras and Terminals (EST Cameras and
Terminals) shall not be solely or primarily used as an eective diagnostic device for COVID-19. Elevated
body temperature should be conrmed with secondary evaluation methods (e.g., a Health Canada
approved contact thermometer). Users, through their experience with the Hikvision EST Cameras and
Terminals in the particular environment of use, should determine the signicance of any fever or elevated
temperature based on the skin telethermographic temperature measurement. Visible thermal patterns
are intended only for locating the points from which to extract the thermal measurement.
To ensure the accuracy of the human skin-surface temperature measurement, the technology shall be
used to measure only one subject’s temperature at a time and shall not be used to measure multiple
individuals’temperatures simultaneously.

3.2 Wiring with Secure Door Control Unit
5. Add Identity Picture
4. Activation
5. Temperature Measurement
1. Use nger to hold the screen surface and enter the activation password to enter the Home
page.
2. Enter the User Management page, tap + to enter the Add User page.
3. Set the user parameters according to actual needs.
4. Tap Face and add the identity information according to the instructions.
You can view the captured picture on the screen. Make sure the identity picture is in good
quality and size.
For tips and recommended positions when collecting or comparing the identity pictures,
see the contents on the right.
5. If the picture is in good condition, tap Save, or tap Try Again to take another identity
picture.
6. Tap √ to save the settings.
Go back to the initial page to start authentication.
For other authentication methods, see the device user manual.
User other authentication methods if the device is aected by the light or other items.
·1:N Matching: The device will compare the captured identity picture with the ones in the
database.
·1:1 Matching: The device will compare the captured identity picture with the user linked
identity picture.
Biometric recognition products are not 100% applicable to anti-spoofing
environments. If you require a higher security level, use multiple authentication modes.
Power on and wire the network cable after installation. Activate the device before the rst login.
If the device is not activated, it will enter the Activate Device page after powering on.
Steps:
1. Create a password and conrm the password.
2. Tap Activate to activate the device.
For other activation methods, see the device user manual.
We highly recommend that you create a
strong password of your own choosing (using
a minimum of 8 characters, including at
least three kinds of the following categories: upper
case letters, lower case letters, numbers, and special
characters) in order to increase the security of your
product. We also recommend that you change your
password regularly. Especially in high security systems,
changing the password monthly or weekly can better
protect your product.
1. Hold the screen surface and verify the identity to enter the Home page.
2. Tap Temp to enter the Temperature Settings page.
3. Congure the parameters.
• Enable Temperature Detection: When the function is enabled, the device will authenticate the permissions and at the same time take the temperature. When the
function is disabled, the device will authenticate the permissions only.
• Over-Temperature Threshold: Edit the threshold according to actual situation. If the detected temperature is higher than the congured one, an alarm will be
triggered. By default, the value is 37.3°.
• Temperature Compensation: If the measured temperature is higher/lower than the actual object’s temperature, you can set the compensation temperature here.
Available range: -99 °C to 99 °C.
• Door Not Open If Temp. is Abnormal: When Enabling the function, the door will not open when the detected temperature is higher than the congured temperature
threshold. By default, the function is enabled.
• Temperature Measurement Only: When enabling the function, the device will not authenticate the permissions, but only take the temperature. When the function is
disabled, the device will authenticate the permissions and at the same time take the temperature.
• Unit: Select a temperature unit according to your preference.
• Measurement Area Calibration/Measurement Area Settings: Congure the temperature measurement area and the correction parameters.
Regulatory Information
FCC Information
Please take attention that changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC Compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This product and, if applicable, the supplied accessories too are marked with“CE”and comply therefore with the applicable
harmonized European standards listed under RE Directive 2014/53/EU, EMC Directive 2014/30/EU, RoHS Directive 2011/65/EU.
2006/66/EC (Battery Directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the
European Union. See the product documentation for specic battery information. The battery is marked with this symbol, which
may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier
or to a designated collection point. For more information see: www.recyclethis.info
2012/19/EU (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see: www.recyclethis.info
This product and, if applicable, the supplied accessories too are marked with“CE”and comply therefore with the applicable
harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
Warning
• In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.
• Use a surge suppressor at the inlet opening of the equipment under special conditions such as mountain tops, iron towers, and forests.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
• An all-pole mains switch shall be incorporated in the electrical installation of the building.
• This equipment is not suitable for use in locations where children are likely to be present.
• CAUTION: Risk of explosion if the battery is replaced by an incorrect type.
• Improper replacement of the battery with an incorrect type may defeat a safeguard (e.g., in the case of some lithium battery types).
• Do not dispose of the battery in re or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.
• Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of
ammable liquid or gas.
• Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of ammable liquid or gas.
• Dispose of used batteries according to the instructions.
• CAUTION: This bracket is intended for use only with the DS-K1T341BMWI-T Temperature Screening Terminal. Use with other equipment
may result in instability causing injury.
• CAUTION: This equipment is for use only with Hikvision’s bracket. Use with other (carts, stands, or carriers) may result in instability causing
injury.
• To prevent possible hearing damage, do not listen at high volume levels for long periods.
• Do not connect several devices to one power adapter as adapter overload may cause overheating or re hazard.
• Please make sure that the power has been disconnected before you wire, install, or dismantle the device.
• When the product is installed on a wall or ceiling, the device shall be rmly xed.
• If smoke, odors, or noise rise from the device, turn o the power at once, unplug the power cable, and then contact the service center.
• If the product does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the device yourself.
(We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
Caution
• The equipment has been designed, when required, modied for connection to an IT power distribution system.
• +identies the positive terminal(s) of equipment that is used with, or generates, direct current. –identies the negative terminal(s) of
equipment that is used with, or generates, direct current.
• No naked ame sources such as lighted candles should be placed on the equipment.
• The equipment serial port is used for debugging only.
• Burned ngers may occur when handling the ngerprint sensor metal; wait one-half hour after switching o before handling the parts.
• Install the equipment according to the instructions in this manual.
• To prevent injury, this equipment must be securely attached to the oor/wall in accordance with the installation instructions.
• Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetic radiation.
• Avoid equipment installation on a vibrating surface or places subject to shock (ignorance can cause equipment damage).
• Do not place the device in extremely hot (see device specication for operating temperature), cold, dusty, or damp locations.
• The device cover for indoor use shall be kept from rain and moisture.
• Exposing the equipment to direct sunlight, low ventilation, or heat source such as heater or radiator is forbidden (ignorance can cause re
danger).
• Do not aim the device at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and
aect the sensor endurance at the same time.
• Use the provided glove when opening the device cover. Avoid direct contact with the device cover, because the acidic sweat of the ngers
may erode its surface coating.
• Please use a soft and dry cloth when cleaning inside and outside surfaces of the device cover, do not use alkaline detergents.
• Please keep all wrappers after unpacking them for future use. In case any failure occurs, must return the device to the factory with the
original wrapper.
• Transportation without the original wrapper may result in damage to the device and lead to additional costs.
• Improper use or replacement of the battery may result in explosion hazard. Replace with the same or equivalent type only. Dispose of
used batteries according to the instructions provided by the battery manufacturer.
• Biometric recognition products are not 100% applicable to anti-spoong environments. If you require a higher security level, use multiple
authentication modes.
• Make sure that the biometric recognition accuracy will be aected by the collected pictures’quality and the light in the environment,
which cannot be 100% correct.
QSG DS-K1T341BMWI-TTouchless Identity Authentication Terminal 31521NA