LTS LTPTZIP762X20IR User manual

IR High-definition Network
Speed Dome
Installation Manual

Installation Manual of IR High-Definition Network Speed Dome
1
Thank you for purchasing our product. If there are any questions, or requests, please do not
hesitate to contact the dealer.
This manual applies to IR High-Definition Network Speed Dome.
This manual may contain several technical or printing errors, and the content is subject to change
without notice. The updates will be added to the new version of this manual. We will readily
improve or update the products or procedures described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security
or signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined
in UL’s Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or
reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.

Installation Manual of IR High-Definition Network Speed Dome
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of
as unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed
of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.

Installation Manual of IR High-Definition Network Speed Dome
3
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid
danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Warnings Follow these safeguards to
prevent serious injury or death.
Cautions Follow these precautions to
prevent potential injury or material
damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety regulations,
fire prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided by normal company. The standard of the
power adapter is 24VAC10% or 12VDC10% (depending on models). The power consumption
cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-heat
or fire hazard.
Please make sure that the power has been disconnected before you wire, install or dismantle
the speed dome.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility
for problems caused by unauthorized repair or maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or places
subject to shock (ignorance can cause equipment damage).
Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire or
electrical shock will occur. The operating temperature should be -30°C ~ 65°C.
The dome cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or
radiator is forbidden (ignorance can cause fire danger).
Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur

Installation Manual of IR High-Definition Network Speed Dome
4
otherwise (which is not a malfunction however), and affecting the endurance of sensor at the
same time.
Please use the provided glove when open up the dome cover, avoid direct contact with the
dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome
cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, do
not use alkaline detergents.
Do not stare at infrared LED closely to avoid hurting your eyes when the infrared lights are on.
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you
need to return the speed dome to the factory with the original wrapper. Transportation without
the original wrapper may result in damage on the speed dome and lead to additional costs.

Installation Manual of IR High-Definition Network Speed Dome
5
Table of Contents
Chapter 1 Installation............................................................................................................................................ 6
1.1 Installation and Cabling........................................................................................................................................ 6
1.1.1 Installing the Speed Dome ............................................................................................................................... 6
1.1.2 Connecting the Cables ..................................................................................................................................... 9
1.2 Alarm Input and Output Connection.................................................................................................................. 10
1.3 Power Cable Requirement ................................................................................................................................. 10
Chapter 2 Mounting Applications ........................................................................................................................11
3.1 Wall Mounting Applications............................................................................................................................... 11
2.1.1 Components................................................................................................................................................... 11
2.1.2 Wall Mounting ............................................................................................................................................... 12
3.2 Corner Mounting Applications ........................................................................................................................... 13
3.2.1 Components................................................................................................................................................... 13
3.2.2 Corner Mounting ........................................................................................................................................... 14
3.3 Pole Mounting Applications ............................................................................................................................... 15
3.3.1 Components................................................................................................................................................... 15
3.3.2 Pole Mounting................................................................................................................................................ 17
3.4 Pendant Mounting Applications......................................................................................................................... 19
3.4.1 Components................................................................................................................................................... 19
3.4.2 Pendant Mounting ......................................................................................................................................... 19
Appendix .....................................................................................................................................................................22
Appendix 1 Lightning & Surge Protection....................................................................................................................... 22
Appendix 2 Waterproof .................................................................................................................................................. 26
Appendix 3 Bubble Maintenance ................................................................................................................................... 28
Appendix 4 RS485 Bus Connection................................................................................................................................. 29
Appendix 5 24VAC Wire Gauge & Transmission Distance .............................................................................................. 32
Appendix 6 Wire Gauge Standards................................................................................................................................. 33

Installation Manual of IR High-Definition Network Speed Dome
6
Chapter 1 Installation
Before you start:
Check the package contents and make sure that the device in the package is in good condition and
all the assembly parts are included.
Note: Do not drag the waterproof cables as shown in Figure 1-1, otherwise the waterproof
performance is affected.
Figure 1-1 Do not Drag the Cables
1.1 Installation and Cabling
1.1.1 Installing the Speed Dome
The wall mount is taken as an example below.
Steps:
1. Remove the protective sticker as shown in Figure 1-2.
Figure 1-2 Protective Sticker
Protective
Sticker

Installation Manual of IR High-Definition Network Speed Dome
7
2. Remove the cover on the back of the speed dome as shown in Figure 1-3. Insert the SD card to
the SD card slot and install the cover back.
SD CARD
SD CARD
SD CARD
Figure 1-3 SD Card Slot
3. Secure the mount to the wall with four screws. Please refer to the chapter 2 and chapter 3 for
different installation methods.
Figure 1-4 Install the Wall Mount
Notes:
For cement wall, you need to use the expansion screw to fix the mount. The mounting hole
of the expansion pipe on the wall should align with the mounting hole on the mount.
For wooden wall, you can just use the self-tapping screw to fix the mount.
Please make sure that the wall is strong enough to withstand more than 8 times the weight
of the dome and the mount.
The mount in Figure 1-4 is the recommended mount for this series of speed dome, and a
pendent adapter is required if any other mount is selected. See Figure 1-5.
The dimension of pendant adapter is G11
2.
SD Card Slot

Installation Manual of IR High-Definition Network Speed Dome
8
Figure 1-5 Pendent Adapter
4. Install the speed dome to the mount.
1) Hang the safety rope to the speed dome and the hook on the mount as shown in Figure
1-6.
2) Route the cables of the speed dome through the wall mount.
3) Connect the corresponding cables. For the detailed information, please refer to section
1.1.2 Connecting the Cables.
Figure 1-6 Install the Speed Dome
4) Loosen the two lock screws on the wall mount.
5) Install the speed dome to the mount. Rotate the speed dome clockwise tightly.
6) Secure the two lock screws with the Allen wrench as shown in Figure 1-7.
Safety Rope
Pendent
adapter

Installation Manual of IR High-Definition Network Speed Dome
9
Figure 1-7 Secure the Speed Dome
1.1.2 Connecting the Cables
Before you start:
Please make sure the power of the dome is off before connecting the cables.
The cable interfaces of speed dome are shown in the following figures. Please refer to the following
figure for connecting the cables.
VI EOD
RED AC24V
YELLOW/GREEN
BLACK AC24V
ORANGE RS48+
YELLOW RS48-
Lock Screw
Black/White
Gray
White
Yellow &Green
Orange
Brown/White
Black
Red
Yellow
Red/White
Orange/White
Green/White
Blue/White
Purple/White
Black
Red
Blue
Green
Pink
Purple
Label 
Label 
Video Output
Network

Installation Manual of IR High-Definition Network Speed Dome
10
Figure 1-8 Cables of Network Speed Dome
1.2 Alarm Input and Output Connection
The network speed dome can be connected with alarm inputs (0~5VDC)
Refer to the following diagrams for alarm output:
JQC-3FG
Relay
30VDC
GND OUT
L N
～220V AC
Relay Output
Dome
(10 A 250VAC)
Diagram (left) Diagram(right)
1A
OUT(n)
OUT(n)
+
-
DC
DC Load
Relay Output
Dome OUT(n)
OUT(n)
Figure 1-9 Alarm Out Connections
The alarm provides the relay output, and the external power supply is required when it connects to
the alarm device.
For DC power supply (left diagram), the input voltage must be no more than 30VDC, 1A.
For AC power supply, the external relay must be used (right diagram) to prevent damages to the
speed dome and avoid risk of electric shock.
1.3 Power Cable Requirement
When the speed dome uses standard AC power supply, the power cable should meet the demand.
The formula of the cross-section S (mm²) and the maximum transmission distance L (m) of the bare
wire is as follows:
L=50*S (analog speed dome)
L=40*S (network speed dome)
Example:
For the analog speed dome, the cross-section of the cable is 1mm²and the transmission distance is
less than 50m.
According to the Appendix 5 24VAC Wire Gauge Standards, for example, the American wire gauge
18, the transmission distance should be 0.7854*50=39.27m.

Installation Manual of IR High-Definition Network Speed Dome
11
Chapter 2 Mounting Applications
Before you start:
For cement wall, you need to use the expansion screw to fix the mount. The mounting hole of
the expansion pipe on the wall should align with the mounting hole on the mount.
For wooden wall, you can just use the self-tapping screw to fix the mount.
The wall must be thick enough to install the expansion screws.
Please make sure that the wall is strong enough to withstand more than 8 times the weight of
the dome and the mount.
3.1 Wall Mounting Applications
2.1.1 Components
Wall Mount
Figure 2-1 Wall Mount
Mounting Accessories
Figure 2-2 Nuts and Flat Washers

Installation Manual of IR High-Definition Network Speed Dome
12
2.1.2 Wall Mounting
Steps:
1. Drill 4 screw holes in the wall according to the holes of the mount, and then insert M6
expansion screws (not supplied) into the mounting holes.
2. Attach the gasket(not supplied) then wall mount to the wall by aligning the 4 screw holes of the
mount with expansion screws on the wall.
3. Secure the wall mount with 4 hex nuts and washers.
Figure 2-3 Drill Screw Holes
4. Install the speed dome to the mount. Please refer to Section 1.1 Installation and Cabling for
installation details.
Figure 2-4 Finish the Installation

Installation Manual of IR High-Definition Network Speed Dome
13
3.2 Corner Mounting Applications
Before you start:
The corner mounting is applicable to the indoor/outdoor 90°solid corner construction.
3.2.1 Components
Wall Mount
Figure 2-5 Wall Mount
Corner Adapter
A corner adapter has to be used together with a wall mount for corner mounting applications.
Figure 2-6 Corner Adapter
Mounting Accessories
Figure 2-7 Hex Screws (M8×30), Nuts, Spring Washers and Flat Washers

Installation Manual of IR High-Definition Network Speed Dome
14
3.2.2 Corner Mounting
1. Install the corner adapter.
Steps:
(1) Drill four holes in the corner according to the screw holes of the corner adapter, and then
insert M8 expansion screws (not supplied) into the holes.
(2) Pull the cables through the center hole of the corner adapter.
(3) Attach the corner adapter to the corner by aligning the 4 screw holes of the corner adapter
with expansion screws on the corner.
(4) Secure the corner adapter to the corner with the nuts and washers to tighten the four
expansion screws.
Figure 2-8 Install the Corner Adapter
Note: Make sure that the cables have enough length. For outdoor applications, please apply the
sealant around the center hole for waterproof.
2. Attach the gasket then the wall mount to the corner adapter.
3. Secure the wall mount to the corner adapter with 4 hex screws and spring washers.
Note: When tightening the screw, it is better to compress the spring washer tightly first and then
rotate it half-turn for water-proof without damaging the threads.
Figure 2-9 Install the Wall Mount
4. Install dome to the mount. Please refer to Section 1.1 Installation and Cabling for installation
Nuts and
Washers

Installation Manual of IR High-Definition Network Speed Dome
15
details.
Figure 2-10 Finish the Installation
3.3 Pole Mounting Applications
3.3.1 Components
Wall Mount
Figure 2-11 Wall Mount
Pole Adapter
A pole adapter has to be used together with a wall mount for pole mounting applications.

Installation Manual of IR High-Definition Network Speed Dome
16
Figure 2-12 Pole Adapter
Pole Mounting Hoops
Pole mounting hoop is used for pole mounting with pole adapter and wall mount. There are
following dimensions selectable: φ59-82mm, φ84-108mm, φ103-127mm, φ130-152mm,
φ155-178mm, φ180-203mm and φ194-216mm. Dimensions can be customized according to your
demand.
Note: The dimensions of the pole mounting hoop must match with the diameter of the pole
adapter.
Figure 2-13 Pole Mounting Hoops
Mounting Accessories

Installation Manual of IR High-Definition Network Speed Dome
17
Figure 2-14 Hex Screws (M8×30) and Spring Washers
3.3.2 Pole Mounting
Steps:
1. Assemble the pole adapter.
(1) Loosen the three pole mounting hoops with a screwdriver.
(2) Insert them through the rectangle holes of the pole adapter.
Figure 2-15 Assemble the Hoops and the Pole adapter
2. Install the pole adapter.
(1) Pull the cables through the center hole.
(2) Secure the three pole mounting hoops to the pole, and tighten the screws of the hoops with
a screwdriver.

Installation Manual of IR High-Definition Network Speed Dome
18
Figure 2-16 Install the Pole Adapter
Note: For outdoor applications, please adopt the water-proof measures.
3. Install the wall mount.
(1) Attach the gasket then wall mount to the pole adapter.
(2) Secure the wall mount to the pole adapter with 4 hex screws and the spring washers.
Figure 2-17 Install the Wall Mount
4. Install the speed dome to the mount. Please refer to Section 1.1 Installation and Cabling for
installation details.

Installation Manual of IR High-Definition Network Speed Dome
19
Figure 2-18 Finish the Installation
3.4 Pendant Mounting Applications
3.4.1 Components
Pendant Mount
Figure 2-19 Pendant Mount
3.4.2 Pendant Mounting
Steps:
1. Install the mounting base.
Steps:
(1) Drill four φ8 holes in the ceiling according to the screw holes of the mounting base, and