XtendLan SDOMEOAT2-SD332 User manual

High Speed Dome
User Manual
SDOMEOAT2-SD332

2/16
Before Installing
Installation should be carried out only by qualified personnel and in accordance
with any wiring regulations in force at the time.
Please read this instruction and warnings before installing.
Do not attempt to service or repair the speed domes as opening or removing
covers may expose dangerous voltages or other hazards. Refer all servicing to
qualified service personnel.
Adequate protection against lightning strikes and power surges must be installed
to prevent damage to the speed dome.
Key Features
360º Panning, speed is 0.1º-300º/s.
Auto flip 180º
128 presets, the error of preset will less than 0.1º
4 dynamic privacy zones
Auto cruise by preset, the dwell time is 1s-250s.
Image freeze while panning
Manifold of scan, scan speed could be setting from 1º/s to 80º/s
Left and right limit scan.
7 alarm input and 2 relay output.
Easy fixing configuration
24V power supply built in
Static proof and thunder proof design of the RS485 connector and video
connecter.

3/16
Environmental requisition:
Operation Temperature: -40-+60
Humidity: <90%
Air pressure: 86-106Kpa
Power supply:AC24V/2.5A, 50/60Hz
The system setting Camera and
Switch SW1 address switch
Alarm connector 8P Short connector
RS485 communication 2P
AC24V power supply
AUX 4P
1、Power supply and
communication cable:：
AC24V
AC24V RS485
2、Video output：
Alarm signal
Alarm Relay Output “AUX1”
Alarm Relay Output “AUX2
Alarm Input GND
Alarm input signal l -7
AL1、AL2、AL3、AL4…AL7：Alarm input.

4/16
1, Dome setting Instruction
The switch setting SW1 ON=1 OFF=0
Protocol setting
Baud rate setting
Alarm
Alarm mode
DIP Switch
1
2
3
4
5
6
7
8
SW1234=
0000=PELCO-D/PELCO-P Auto
identify
SW5,6=
00=2400
01=4800
10=9600
11=19200
1=Alarm
enable
0=Alarm
disable
1=Always short
circuit.(Alarm
while open)
0=Always
open
circuit.(Alarm
while short)
Note ： PELCOD PELCOP could be identifying automatically. On and off is the corresponding
switch position.
SW2 switch: address switch table.
CAM ID
1
2
3
4
5
6
7
8
1
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
3
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
5
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
7
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
8
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
9
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
10
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
11
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
12
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
13
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
14
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
15
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
16
ON
ON
ON
ON
OFF
OFF
OFF
OFF
∶
∶
∶
128
ON
ON
ON
ON
ON
ON
ON
129
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
∶
∶
∶
255
ON
ON
ON
ON
ON
ON
ON
OFF
256
ON
ON
ON
ON
ON
ON
ON
ON

5/16
High Speed Dome
Ver：1 00
PELCO D P
2400
ID：001
Tilereference OK
Pan reference OK
SONY FCB-EX480CP
Alarm
7 alarm input. The dome will alarm when alarm input port connect the GND. The AUX will be
closed when has alarm, and open when on alarm in. The capacitance of the relay isAC24V/1A.
The relay output:
2 relay switchAUX1,AUX2, the biggest capability is AC24V/1A. AUX1 connect with the alarm, the
master or keyboard controlsAUX2.
Camera Module Setting Switch
The dome can be fit different camera, and they have different
switch.
Camera
Switch 1
Switch 2
Switch 3
Switch 4
DIP-1
DIP-2
DIP-3
DIP-4
SONY
OFF
OFF
OFF
OFF
HITACHI
OFF
OFF
ON
OFF
LG
OFF
ON
OFF
OFF
CNB-200L
OFF
ON
ON
OFF
CNB-M1560
OFF
ON
ON
ON
SAMSUNG
(SDM300/SDM330)
ON
OFF
OFF
OFF
Note: Please make sure the camera parameters are correct or the camera cannot work
or cannot work well. If this, please enter the camera menu and restore factory settings first,
then setting the parameters as request.
High Speed Dome Operation,
When Electric
When electric the dome, the version, protocol, baud rate, ID will display on the monitor, and the
dome will check automatic with vertical and level then display the specs of camera.
Example:

6/16
Camera ►
Pan ►
Shortcut Key
Self act
Nothing
Leisure Time
030
The operation way by keyboard controller
Function
Control
Level/Vertical
Joystick left, right/ up and down
OSD Confirm
OPEN
Cancel and Back
CLOSE
OSD Display
Call 95 preset
Zero Position
Call 34 preset
Level Scan
Call 99 preset
Auto Flip
Call 33 preset
Left limit: call 92 preset
Level Scan Limit
Point
Right limit: call 93 preset
Call preset scan 1
Call 81 preset
Call preset scan 2
Call 82 preset
Call preset scan 3
Call 83 preset
Call preset scan 4
Call 84 preset
Camera mode 1
Call 100 preset
Camera mode 2
Call 101 preset
Camera mode 3
Call 102 preset
4 Privacy mask, only fit to SONY480, SONY980 and HITACHI454 camera.
Level area increase: FAR
Level area reduce: NEAR
Vertical area increase: TELE
Privacy Mask
Vertical area reduce: WIDE
OSD Operation
1, Enter OSD
Please call the number 95 preset to display the OSD on the screen.
At figures the current item, figures the enabled item, and the ► after the item which have
submenu. You can change the item state when it has been enabled. Please press OPEN key to
enter or confirm and CLOSE key to back or cancel, and the key UP and DOWN control the cursor
up and down.
2 Menu function instructions
Call the number 95 preset to enter the OSD, and you also could set the shortcut key to display the
OSD.
Main Menu

7/16
Exposure ►
White Balance ►
Privacy ►
Other ►
Camera Model ►
Zoom Speed
005
Focus Speed
001
Exp Mode
Auto
Shutter speed
006
Iris
016
Gain
001
Bright
016
Back Light
Off
Slow Shutter
Off
Exposure ►
White Balance ►
Privacy ►
Other ►
Camera Model ►
Zoom Speed
005
Focus Speed
001
Camera OSD
Camera ► Press OPEN to enter the camera menu.
Camera Exposure
Exposure ►Press OPEN key to enter the camera exposure submenu.
Exposure operation
1, How to change the exposure
Exp Mode press OPEN key, enable Exp Mode, then
operate up and down by the joystick, the parameters are:
Auto, Manual, Shutter, Iris and bright
2 Confirm Exposure.
Exp Mode press OPEN key, select effect, the
menu change to Exp Mode
3 Cancel Exposure
Exp Mode press CLOSE to cancel the Exposure mode change, the menu change to
Exp Mode
Back the main camera menu
Exp Mode press CLOSE key to cancel the last menu.
Other operation of Exposure Menu
Exp Mode, control the joystick up or down to let the up and down, press OPEN key to
enable the item, then go on control up and down with joystick, and press OPEN key to confirm,
the cursor will change to .
White Balance
The dome has the function of Manual White Balance and Auto White Balance.
White Balance ► press OPEN key, enter the White
Balance submenu, then change the parameter,
WB Mode Auto
R Gain 214(0-255)
B Gain 175(0-255)

8/16
WB Mode
Auto
R Gain
210
B Gain
175
WB Mode
Auto
R Gain
210
B Gain
175
WB Mode
Auto
R Gain
210
B Gain
175
Exposure ►
White Balance ►
Privacy ►
Other ►
Camera Model ►
Zoom Speed
005
Focus Speed
001
Privacy1
Privacy2
Privacy3
Privacy4
White Balance Mode operation:
1、WB Mode
2、At WB Mode, press OPEN key to enable the Exp
Mode menu, then it will change to WB Mode,
control the joystick to change the parameter which
order is: Auto, Manual, ATW, OPW, Outdoor and
Indoor. R Gain
3, R Gain
At WB Mode, operate the joystick down let the
cursor come to R Gain, press OPER key to enter the
menu. Then operate the joystick up (increase) and down
(reduce) the R Gain. The homologous parameter is 0-255.
Press OPEN key to confirm and back or press CLOSE to
cancel and back.
4, B Gain
At WB Mode operate the joystick to control the
cursor come to B Gain, press OPEN key to enter the B
Gain setting, joystick up and down to increase and reduce
the parameter which from 0-255. Press OPEN key to
confirm and back or press CLOSE to cancel and back.
Privacy Mask
At Exposure ► operate the joystick to let the
cursor come to Privacy press OPEN to enter the
submenu, then set the parameter.
There are 4 privacy masks, which have the same
operation.
1, Set privacy mask
At the submenu of the Privacy, press OPEN key to enter
the adjust image, adjust the privacy zone by OPEN
(confirm), CLOSE (cancel), FAR (level increase), NEAR
(level reduce), TELE (vertical increase), WIDE (vertical
reduce). Then press OPEN key to confirm and back.
图:2.3.4

9/16
Digital Zoom
On
Auto ICR
Off
ICR
Off
Display
Off
Camera Mode Save：
Day Mode
Night Mode 1
Night Mode 2
Camera Mode Exec：
Day Mode
Night Mode 1
Night Mode 2
Privacy ►
Other ►
Camera Model ►
Zoom Speed
005
Focus Speed
001
Exposure ►
White Balance ►
Privacy ►
Other ►
Camera Model ►
Zoom Speed
005
Focus Speed
001
2, Clare privacy masks.
a, Restart the speed dome, all of the privacy mask will be cleared.
b, Enter the menu of the Privacy mask, press OPEN key to enter and press CLOSE to clear
the privacy mask you want to clear.
Others of the Camera menu
Press OPEN key to enable the submenu, operate
joystick to change the states of ON and OFF. Press
OPEN to confirm and back and CLOSE to cancel and
back.
Camera Mode
Camera Mode setting menu:
Press OPEN to enter the menu.
There are three mode under the Camera Mode Save
menu, move the cursor to the mode going to be change,
press OPEN the cursor will change to , the setting will
be saved and it will back to after 1 second.
The three items under Camera Mode Exec is opposite
the three modes above. Move the cursor to the mode
you want to call and press OPEN to confirm and back.
The saved mode could be called by the shortcut preset: Night Mode1—call 101 preset, Night
2---- call 102 preset.
Zoom Speed
At the submenu of Exposal, move the cursor to Zoom Speed, press OPEN, the cursor will
change to , then the parameter can be changed. Press OPEN to confirm and back or CLOSE
cancel and back.
Focus Speed
Move the cursor to Focus Speed, press OPEN, the cursor will change to , then the parameter
can be changed. Press OPEN to confirm and back or CLOSE cancel and back.

10/16
Open Menu
095
Auto Flip
033
Reference
034
Left Limit
092
Right Limit
093
Preset scan 1
081
Preset scan 2
082
Preset scan 3
083
Preset scan 4
084
Auto Scan
099
Camera ►
Pan ►
Shortcut Key
Self act
Nothing
Leisure Time
030
Home place
Off
AS speed
060
PS1 Speed
120
PS1 time
005
PS2 Speed
120
PS2 time
005
PS3 Speed
120
PS3 time
005
PS4 Speed
120
PS4 time
Auto Flip
On
Pan This operation can control the home place of the dome,
adjust the auto panning speed and 4 cruise line with
presets, also the auto flip function.
Home Place OFF (001-032, OFF)
AS Speed 060(000-080) Auto Pan speed
PS1 Speed 120(100-120) Presets cruise 1 speed
PS1 Time 005(5-120) ) Presets cruise 1 stop time.
PS2 Speed 120 Presets cruise 2 speed
PS2Time 005 Presets cruise 2 stop time.
PS3 Speed 120 Presets cruise 3 speed
PS3 Time 005 Presets cruise 3 stop time.
PS4 Speed 120 Presets cruise 4 speed
PS4 Time 005 Presets cruise 4 stop time.
Auto Flip On(On/Off)
Shortcut Key
The functions can be setting by presets number, and can be called by the preset number which
be set. Note: The right side number is the default short cut key,
they are the number of presets. The number can be saved by new shortcut but the old one will not
be cancel.
Example: Change the number 095 into 16 that after Open Menu, the Menu can be called by 16
preset, and also can be called by 95 preset.
In the presets, the preset scan line 1 will cruise from
presets 1-8, and preset scan line 2 will cruise from
presets 9-16, the preset scan line 3 will cruise from
presets 17-24, and the preset scan line 4 will cruise from
25-32. Every line will back the first preset when it met
the point never be set, and it will quit cruise if the first
preset is not be set. The function Auto Scan is right and
left limit scan.
Note: The changing of the shortcut key can not be
identical with the shortcut key already have.
Operation: Move the cursor to the item which going to be changed, press OPEN, then change the
parameter, press OPEN to confirm and back or CLOSE cancel and back.
Self Act.
The dome will check itself when electric and it will act
the program automatic.
Nothing
P Scan 1 Preset scan 1
P Scan 2 Preset scan 2
P Scan 3 Preset scan 3
P Scan 4 Preset scan 4

11/16
Camera ►
Pan ►
Shortcut Key
Self act
Nothing
Leisure Time
030
A Scan Auto scan (left and right limit scan
Home Home place
Operation: Press OPEN the cursor will change to , and the parameter can be change. Press
OPEN to confirm and back or CLOSE to cancel and back.
Leisure Time
The dome will back to the home place after a while if it
moved manual, an the time is Leisure Time
The parameter is from 1-240.
Operation: Press OPEN the cursor will change to , and
the parameter can be change. Press OPEN to confirm and
back or CLOSE to cancel and back.
High speed dome with SONY CAMERA MODULE MENU
Menu
Submenu
Third Menu
Parameter
Exp Mode
Auto（Auto，manual；shutter，iris，bright）
Shutter speed
006(0~19)
Iris
015(0~17)
Gain
001(0~15)
Bright
015(0~18)
Back Light
OFF(ON/OFF)
Exposure
Slow Shutter
OFF(ON/OFF)
WB Mode
Auto( Auto，Manual；ATW，OPW，Outdoor，Indoor)
R Gain
210(0~255)
White Balance
B Gain
175(0~255)
Privacy1
Privacy2
Privacy3
Privacy
Privacy4
Digital Zoom
On(On/ Off)
Auto ICR
Off(On/ Off)
ICR
Off(On/ Off)
Other
Display
Off(On/ Off)
Camera Model Save：
Day Mode
Night Mode 1
Night Mode 2
Camera Model Exec
Day Mode
Night Mode 1
Camera Model
Night Mode 2
Zoom Speed
005(001~007)
Camera
Focus Speed
001(001~007)
Home place
OFF(001-032,OFF)
AS speed
060(000-080)
Pan
PS1 Speed
120(100-120)
图:2.d

12/16
PS1 time
005(005-120)
PS2 Speed
120(100-120)
PS2 time
005(005-120)
PS3 Speed
120(100-120)
PS3 time
005(005-120)
PS4 Speed
120(100-120)
PS4 time
005(005-120)
Auto Flip
On(On/Off)
Open Menu
095
Auto Flip
033
Reference
034
Left Limit
092
Right Limit
093
Preset scan 1
081
Preset scan 2
082
Preset scan 3
083
Preset scan 4
084
Shortcut
Key
Auto Scan
099
Self act
Nothing (Nothing ,P Scan 1,P Scan 2,P Scan 3 , P
Scan 4, Pattern 1, Pattern 2, Pattern 3)
Leisure
Time
030(001~014)
OSD Operation way:
FAR
Confirm
NEAR
Cancel and Back
Joystick
Control the cursor up and down or setting the parameters
►
Which have submenu, and press FAR key to enter.
Currently menu.
High speed dome with HITACHI CAMERA MODULE MENU
Menu
Submenu
Third Menu
Parameter
Exposure
Exp Mode
Auto(Auto/AE DSS)
Back light
Off(On/Off)
BLC Level
016
Iris
091(000～255)
White Balance
WB Mode
Auto(Auto/Manual)
R Gain
652(640～767)
B Gain
462(384～511)
Lens
Digital Zoom
On (On/Off)
D Zoom MAG
mag12(mag 0～mag12)
Zoom Speed
High(High,Super h,Normal)
Camera
Focus Speed
016(0～31)
Home place
OFF(001-032,OFF)
Pan
AS speed
060(000-080)

13/16
PS1 Speed
120(100-120)
PS1 time
005(005-120)
PS2 Speed
120(100-120)
PS2 time
005(005-120)
PS3 Speed
120(100-120)
PS3 time
005(005-120)
PS4 Speed
120(100-120)
PS4 time
005(005-120)
Auto Flip
On(On/Off)
Open Menu
095
Auto Flip
033
Reference
034
Left Limit
092
Right Limit
093
Preset scan 1
081
Preset scan 2
082
Preset scan 3
083
Preset scan 4
084
Shortcut
Key
Auto Scan
099
Self act
Nothing (Nothing , Home ,A Scan,P Scan1,P Scan2,P
Scan3, P Scan 4, Pattern1,Pattern2,Pattern 3)
Leisure
Time
030(001~014)
OSD Operation way
NEAR
Exit
FAR
Confirm
TELE
Control the cursor up and
setting the parameters
WIDE
Control the cursor down and
setting the parameters
CLOSE
Quite camera menu and back.
Currently menu
High speed dome with CNB CAMERA MODULE MENU
Menu
Submenu
Third Menu
Parameter
BACKLIGHT
OFF(ON/OFF)
SLOW
SHUTTER
FLD24(OFF , FLD2, FLD 4, FLD 8, FLD 12, FLD 16,
FLD 24, FLD 32, FLD 64, FLD128)
DAY/NIGHT
AUTO(ON,OFF,AUTO)
Camera
WB CONTROL
AUTO(AUTO/PUSH)

14/16
SHUTTER
AUTO
CAMERA ID
000(000～255)
ZOOM START
X001(x001～X022)
ZOOM STOP
X220(X220,X209,X198,X187,X176,X165,X154,X143,
X132,X121,X110,X098,X088,X077,X066,X055,
X044,X033,X022,X011,X001)
BRIGHTNESS
10(0～15)
SHARTNESS
25(0～48)
FOCUS
PUSH(PUSH/AUTO)
INIT SET
OFF(ON/OFF)
Home place
OFF(001-032,OFF)
AS speed
060(000-080)
PS1 Speed
120(100-120)
PS1 time
005(005-120)
PS2 Speed
120(100-120)
PS2 time
005(005-120)
PS3 Speed
120(100-120)
PS3 time
005(005-120)
PS4 Speed
120(100-120)
PS4 time
005(005-120)
Pan
Auto Flip
On(On/Off)
Open Menu
095
Auto Flip
033
Reference
034
Left Limit
092
Right Limit
093
Preset scan 1
081
Preset scan 2
082
Preset scan 3
083
Preset scan 4
084
Shortcut
Key
Auto Scan
099
Self act
Nothing (Nothing , Home ,A Scan,P Scan1,P Scan2,P
Scan3, P Scan 4, Pattern1,Pattern2,Pattern 3)
Leisure
Time
030(001~014)
OSD Operation way
NEAR
Confirm or decrease the
parameter；
FAR
Confirm or increase the
parameter
TELE
Up；
WIDE
Down
NOT USE
Can’t be use
Have submenu and back

15/16
High speed dome with LG CAMERA MODULE MENU
FUNCTION
OSD Format
Description
Remarks
Non display
Auto Mode
1
Focus Mode
Manual/ Push Auto mode
Non display
Back Light OFF
2
Back Light
“BL’’display
BLC ON/ Auto BLC Mode
Non display
Normal Shutter：NTSC：1/60
PAL：1/50
“F1”display
Flickerless Mode
3
Shutter
Speed
1/125
：
：
1/10，000
28 variable steps
4
Motion
Detect
MOTION DETECTED
Display when motion is
detected
5
STAND-BY
Mode
Indicate the camera stand-by during the camera’s power turning on
DX270
Digital Zoom Model
6
Zoom
Display
X27
Optical Zoom Model
7
CAMERA ID
According to write the identification number to each camera,
multi-point control is available are available (PC Control 000-255)
AWB
White Balance Auto
SWB
Special Auto White Balance; Adjustment Mode
according to change of external illuminant. RED
ADJUST and BLUE ADJUST (0-255) are
available. After changing R/W value, the
maintenance mode is AUTO.
WB Preset for Indoor
WB Preset for Outdoor
Manual WB Adjustment; In manual mode the
HUE control is available 0-99
8
WBC Mode
PWB
Push Auto White Balance; Turn this mode ON,
the white trace automatically. Turn this mode
OFF, preserve the white of final auto tracing
action (Manual)
The Menu shortcut List of HIGH SPEED DOME WITH LG
Main
Menu
Submenu
Last Menu
Parameters(optical)
Exp Mode
Auto（Auto，manual；shutter up，iris，bright）
Shutter speed
006(0~19)
Iris
015(0~17)
Gain
001(0~15)
Bright
015(0~18)
Back Light
OFF(ON/OFF)
Camera
Exposure
Slow Shutter
OFF(ON/OFF)

16/16
WB Mode
Auto( Auto，Manual；ATW，OPW，Outdoor，Indoor)
R Gain
210(0~255)
White Balance
B Gain
175(0~255)
Privacy1
Privacy2
Privacy3
Privacy
Privacy4
Digital Zoom
On(On/ Off)
Auto ICR
Off(On/ Off)
ICR
Off(On/ Off)
Other
Display
Off(On/ Off)
Camera Model Save：
Day Mode
Night Mode 1
Night Mode 2
Camera Model Exec
Day Mode
Night Mode 1
Camera Model
Night Mode 2
Zoom Speed
005(001~007)
Focus Speed
001(001~007)

Auto Tracking Function User Manual
1. Setting（Note: Wrong setting will cause the function not available）
Protocol：PELCO-P
Baud rate：9600
2, How to usd
The power supply of the auto tracking module is DC12V
It is defined the function off, please use the Preset Order below to operate it.
Order Preset
Functions
35
Start Auto Tracking
36
Stop Auto Tracking
Default
230
When lost the tracking object：Move to 1st preset
Default
231
When lost the tracking object：Stop tracking
232
When lost the tracking object：Keep tracking
233
Sensitivity：Low
234
Sensitivity：Mid
Default
235
Sensitivity：High
236
Object Size：Small
237
Object Size：Mid
Default
238
Object Size：Big
239
Tracking object lost time：5s
240
Tracking object lost time：10s
241
Tracking object lost time：15s
Default
242
Tracking object lost time：20s
243
Tracking object lost time：25s
244
Tracking object lost time：30s
245
Tracking object lost time：35s
246
Tracking object lost time：40s
247
Zoom：On
248
Zoom：Off
Default