HIK VISION TurboHD DS-2CE16D0T-WL5 User manual

UM DS-2CE16D0T-WL5 061818NA  2018 Hikvision USA Inc.
TurboHD
DS-2CE16D0T-WL5
TVI Bullet Camera
User M nu l
Th nk you for purch sing our product. If there re ny questions or requests, do
not hesit te to cont ct the de ler.
This m nu l m y cont in sever l technic lly incorrect pl ces or printing errors,
nd the content is subject to ch nge without notice. The upd tes will be dded
to new versions of this m nu l. We will re dily improve or upd te the products
or procedures described in the m nu l.

UM DS-2CE16D0T-WL5 061818NA  2018 Hikvision USA Inc.
Regulatory In ormation
FCC In ormation
FCC Compliance: This equipment h s been tested nd found to comply with the
limits for Cl ss A digit l device, pursu nt to p rt 15 of the FCC Rules. These limits
re designed to provide re son ble protection g inst h rmful interference when
the equipment is oper ted in commerci l environment. This equipment
gener tes, uses, nd c n r di te r dio frequency energy nd, if not inst lled nd
used in ccord nce with the instruction m nu l, m y c use h rmful interference to
r dio communic tions. Oper tion of this equipment in residenti l re is likely to
c use h rmful interference in which c se the user will be required to correct the
interference t his own expense.
FCC Conditions
This device complies with p rt 15 of the FCC Rules. Oper tion is subject to the
following two conditions:
1. This device m y not c use h rmful interference.
2. This device must ccept ny interference received, including interference th t
m y c use undesired oper tion
EU Con ormity Statement
This product nd, if pplic ble, the supplied ccessories too re m rked
with “CE” nd comply therefore with the pplic ble h rmonized
Europe n st nd rds listed under the EMC Directive 2014/30/EU, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE Directive): Products m rked with this symbol c nnot
be disposed of s unsorted municip l w ste in the Europe n Union. For
proper recycling, return this product to your loc l supplier upon the
purch se of equiv lent new equipment, or dispose of it t design ted
collection points. For more inform tion see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) st nd rds requirements.
Sa ety Instruction
These instructions re intended to ensure th t user c n use the product correctly to
void d nger or property loss.
The prec ution me sure is divided into “W rnings” nd “C utions.”
Warnings: Serious injury or de th m y occur if ny of the w rnings re neglected.
Cautions: Injury or equipment d m ge m y occur if ny of the c utions re
neglected.
Warnings Follow Cautions Follow these
these s fegu rds to
prec utions to prevent
prevent serious injury
potenti l injury or
or de th.
m teri l d m ge.
Warnings
• In the use of the device, you must be in strict compli nce with the electric l
s fety regul tions of the n tion nd region.
• Input volt ge should meet both the SELV (S fety Extr Low Volt ge) nd the
Limited Power Source with 12 VDC ccording to the IEC60950-1 st nd rd. Refer
to technic l specific tions for det iled inform tion.
• Do not connect multiple devices to one power d pter to void overhe ting or
fire h z rd c used by overlo d.
• M ke sure th t the plug is firmly connected to the power socket.
• M ke sure th t the device is firmly fixed if w ll mounting or ceiling mounting is
dopted.

UM DS-2CE16D0T-WL5 061818NA  2018 Hikvision USA Inc.
• If smoke, odor, or noise rise from the device, turn off the power t once nd
unplug the power cord, nd then cont ct the service center.
• Never ttempt to dis ssemble the c mer by unprofession l person l.
Cautions
• Do not drop the c mer or subject it to physic l shock.
• Do not touch sensor modules with fingers.
• If cle ning is necess ry, use cle n cloth with bit of eth nol nd wipe it gently.
• Do not im the c mer t the sun or extr bright pl ces.
• The sensor m y be burned out by l ser be m. If ny l ser equipment is in use,
m ke sure th t the sensor surf ce is not exposed to the l ser be m.
• Do not expose the device to high electrom gnetic r di tion or extremely hot,
cold, dusty, or d mp environments.
• To void he t ccumul tion, good ventil tion is required for the oper ting
environment.
• Keep the c mer w y from liquid while in use for non-w terproof device.
• While in delivery, the c mer sh ll be p cked in its origin l p cking, or p cking of
the s me texture.

UM DS-2CE16D0T-WL5 061818NA  2018 Hikvision USA Inc.
1Introduction
1.1. Product Features
The c mer is pplic ble for outdoor conditions Applic tion scen rios
include ro ds, p rking lots, c mpuses, etc.
The m in fe tures re s follows:
• High perform nce CMOS sensor
• 1080p resolution
• Auto white b l nce
• Auto electronic shutter
• Auto g in control (AGC)
• White supplement light
• Up-the-Co x (HIKVISION-C)
1.2. Camera Overview
Figure 1, C mer Overview
2Installation
2.1. Installation Preparation
2.1.1 Be ore You Start:
M ke sure th t the device in the p ck ge is in good condition nd
ll the ssembly p rts re included.
M ke sure th t ll the rel ted equipment is powered off during the
inst ll tion.
Check the specific tion of the products for the inst ll tion
environment.
Check whether the power supply m tches your power output to
void d m ge.
M ke sure the w ll is strong enough to withst nd three times the
weight of the c mer nd the br cket.
If the w ll is cement, insert exp nsion bolts before you inst ll the
c mer . If the w ll is wood, use self-t pping screws to secure the
c mer .
If the product does not function properly, cont ct your de ler or
the ne rest service center. Do NOT dis ssemble the c mer for
rep ir or m inten nce yourself.
2.2. Wall Mounting
2.2.1 Be ore You Start:
The p ck ge cont ins the w ll mounting br cket.
2.2.2 Steps:
1. Att ch the br cket to the w ll.
2. M rk the screw holes on the w ll ccording to the holes on
the br cket.
3. Drill the screw holes.

UM DS-2CE16D0T-WL5 061818NA  2018 Hikvision USA Inc.
4. Att ch the br cket to the w ll nd secure the c mer with
supplied screws.
Figure 2, Secure the C mer to the W ll
Note:
• The supplied screw p ck ge cont ins both self-t pping screws nd exp nsion
bolts.
• If the w ll is cement, exp nsion bolts re required to fix the c mer . If the w ll is
wood, self-t pping screws re required.
5. Align the c mer to the pedest l, nd secure the c mer on
the pedest l with supplied screws.
Figure 3, Secure the C mer on the Br cket
Note:
Dr wings re for illustr tion purposes only; your c mer m y ppe r different.
6. Route the c bles nd connect the corresponding power cord
nd video c ble.
7. Power on the c mer to check whether the im ge on the
monitor is t n optimum ngle. If not, djust the c mer
ccording to the figure below to get n optimum ngle.
1). Loosen the horizont l djusting screw to djust the p n
position (0° to 360°).
2). Tighten the horizont l djusting screw.
3). Loosen the vertic l djusting screw to djust the tilt
position (0° to 90°)
4). Tighten the vertic l djusting screw.
Figure 4, Angle Adjustment
2.2.3 Pendant Mounting
Before you start:
You must purch se pend nt br cket.

UM DS-2CE16D0T-WL5 061818NA  2018 Hikvision USA Inc.
Steps:
1. Att ch the br cket to the ceiling.
2. M rk the screw holes on the ceiling ccording to the holes on
the br cket.
3. Drill the screw holes.
4. Att ch the br cket to the ceiling nd secure the c mer with
supplied screws.
Figure 5, Fix the Br cket on the Ceiling
Note:
• The supplied screw p ck ge cont ins both self-t pping screws nd exp nsion
bolts.
• If the w ll is cement, exp nsion bolts re required to fix the c mer . If the w ll is
wood, self-t pping screws re required.
5. Remove the screw on the top of the c mer to expose the
screw hole.
Figure 6, Remove the Screw
6. Align the screw hole on the top of the c mer with the
pend nt mounting br cket nd rot te the c mer to fix it.
Figure 7, Fix the C mer to the Br cket

UM DS-2CE16D0T-WL5 061818NA  2018 Hikvision USA Inc.
7. Route the c bles nd connect the corresponding power cord
nd video c ble.
8. Power on the c mer to check whether the im ge on the
monitor is t n optimum ngle. If not, djust the c mer
ccording to the figure below to get n optimum ngle.
1). Loosen the djusting knob to djust the p n position (0°
to 360°) nd tilt position (0° to 90°).
2). Tighten the djusting knob.
Figure 8, Angle Adjustment