HIK VISION UD04310B User manual

0
Network Bullet Camera
Quick Start Guide
UD04310B

Network Bullet Camera·Quick Start Guide
1
1
Quick Start Guide
COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures,
graphs are the properties of Hangzhou Hikvision Digital Technology
Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
This user manual (hereinafter referred to be “the Manual”) cannot
be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of
Hikvision. Unless otherwise stipulated, Hikvision does not make any
warranties, guarantees or representations, express or implied,
regarding to the Manual.
About this Manual
This Manual is applicable to 4Bxx Network Camera.
The Manual includes instructions for using and managing the
product. Pictures, charts, images and all other information
hereinafter are for description and explanation only. The
information contained in the Manual is subject to change, without
notice, due to firmware updates or other reasons. Please find the
latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the
properties of Hikvision in various jurisdictions. Other trademarks and
logos mentioned below are the properties of their respective
owners.

Network Bullet Camera·Quick Start Guide
2
2
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE
LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

Network Bullet Camera·Quick Start Guide
3
3
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions

Network Bullet Camera·Quick Start Guide
4
4
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info

Network Bullet Camera·Quick Start Guide
5
5
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards
requirements.
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
●Proper configuration of all passwords and other security
settings is the responsibility of the installer and/or end-user.
●In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these precautions
to prevent potential injury or
material damage.

Network Bullet Camera·Quick Start Guide
6
6
●Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
●Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
●If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
●Make sure the power supply voltage is correct before using the
camera.
●Do not drop the camera or subject it to physical shock.
●Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
●Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.

Network Bullet Camera·Quick Start Guide
7
7
●The sensor may be burned out by a laser beam, so when any
laser equipment is in using, make sure that the surface of
sensor will not be exposed to the laser beam.
●Do not place the camera in extremely hot, cold (the operating
temperature shall be-30°C ~+60°C , or -40°C ~ +60°C if the
camera model has an “H” in its suffix), dusty or damp locations,
and do not expose it to high electromagnetic radiation.
●To avoid heat accumulation, good ventilation is required for
operating environment.
●Keep the camera away from liquid while in use.
●While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
●Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average time
varies because of differences between operating environment
and using history, so regular checking is recommended for all
the users. Please contact with your dealer for more details.
●Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
●If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)

Network Bullet Camera·Quick Start Guide
8
8
Table of Contents
1 Appearance Description ................................................................. 9
1.1 Camera Overview............................................................ 9
1.2 Cable Description.......................................................... 10
2 Installation.................................................................................... 13
2.1 Memory Card Installation.............................................. 14
Direct Mounting............................................................ 152.2
Wall Mounting with a Junction Box ............................... 182.3
Wall Mounting with a Gang Box .................................... 192.4
2.5 Installation of Network Cable Water-proof Jacket
(Optional) ................................................................................. 20
3 Setting the Network Camera over the LAN .................................. 23
Wiring ........................................................................... 233.1
Activating the Camera................................................... 243.2
Activation via Web Browser................................ 243.2.1
Activation via SADP Software ............................. 253.2.2
Modifying the IP Address .............................................. 273.3
4 Accessing via Web Browser .......................................................... 30
5 Operating via Hik-Connect App .................................................... 32
5.1 Enable Hik-Connect Service on Camera......................... 32
Enable Hik-Connect Service via SADP Software.. 325.1.1
Enable Hik-Connect Service via Web Browser .... 335.1.2
5.2 Hik-Connect Setup ........................................................ 35
5.3 Adding Camera to Hik-Connect ..................................... 35
5.4 Initializing the Memory Card ......................................... 37
0504051070109

Network Bullet Camera·Quick Start Guide
9
9
1Appearance Description
1.1 Camera Overview
The overview of the network bullet camera is shown below.
1
2
34
5
6
7
OverviewFigure 1-1
DescriptionTable 1-1
No.
Description
1
Photoresistor
2
Lens

Network Bullet Camera·Quick Start Guide
10
10
No.
Description
3
Sun Shield
4
3-axis Bracket
5
Reset Button
6
Memory Card Slot
7
Serial Port
The standard power supply is 12V DC, please make sure your
power supply matches with your camera.
Press RESET about 10s when the camera is powering on or
rebooting to restore the default settings, including the user name,
password, IP address, port No., etc.
1.2 Cable Description
This camera series has several camera models, each of which may
have different cable group. The following figures and tables show the
description of all possible cables in this camera series.

Network Bullet Camera·Quick Start Guide
11
11
1
2
4
5
6
3
7
Cable and Interface OverviewFigure 1-2
Cable and Interface DescriptionTable 1-2
No.
Description
1
Video Out Interface (BNC)
2
RJ45 Network Interface (PoE supported)
3
Power Supply, DC 12V
4
Alarm Input and Output Interface
5
RS-485 Interface

Network Bullet Camera·Quick Start Guide
12
12
No.
Description
6
Audio Out Interface
7
Audio In Interface

Network Bullet Camera·Quick Start Guide
13
13
2Installation
Before you start:
●Make sure the device in the package is in good condition and all
the assembly parts are included.
●The standard power supply is 12V DC, please make sure your
power supply matches with your camera.
●Make sure all the related equipment is power-off during the
installation.
●Check the specification of the products for the installation
environment.
●Make sure that the wall is strong enough to withstand four
times the weight of the camera and the bracket.
For the camera that supports IR, you are required to pay attention to
the following precautions to prevent IR reflection:
●Dust or grease on the dome cover will cause IR reflection.
Please do not remove the dome cover film until the installation
is finished. If there is dust or grease on the dome cover, clean
the dome cover with clean soft cloth and isopropyl alcohol.
●Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing reflection.
●The foam ring around the lens must be seated flush against the
inner surface of the bubble to isolate the lens from the IR LEDS.
Fasten the dome cover to camera body so that the foam ring
and the dome cover are attached seamlessly.

Network Bullet Camera·Quick Start Guide
14
14
2.1 Memory Card Installation
This series of camera supports memory card installation. Please
follow the steps below to install the micro SD card.
1. Loosen the two lock screws at the bottom of the bullet camera,
and then remove the slot cover.
Slot
Cover
Figure 2-1 Remove Card Cover
2. Insert the memory card into the memory card slot.
Memory
Card
Figure 2-2 Insert the Card

Network Bullet Camera·Quick Start Guide
15
15
3. (Optional) To unmount the memory card, push the inserted
memory card to get it ejected.
4. Screw the slot cover back to complete the installation.
Direct Mounting2.2
Before you start:
Bullet cameras of this series are equipped with an integrative
mounting bracket. You can mount the camera directly on wall or
ceiling.
Steps:
1. Past the drill template to the desired mounting place of wall or
ceiling.
Drill TemplateFigure 2-3

Network Bullet Camera·Quick Start Guide
16
16
2. Drill the screw holes according to the Screw Hole 1. (Optional) If
you want to route cables through the wall or ceiling, cut a hole
according to Hole A of the drill template.
Insert the expansion screws first if the camera is mounted to the
cement wall or ceiling. And you can use the self-tapping screws
directly if camera is mounted to the wooden ceiling.
3. Route the cables and fix the camera to the ceiling or wall with the
supplied screws.
Install the CameraFigure 2-4

Network Bullet Camera·Quick Start Guide
17
17
It is recommended to adopt the water-proof jacket (supplied) for
the network interface when the camera is installed outdoor. See
Section 2.5.
4. Adjust the surveillance angle with supplied wrench.
1). Loosen No.1 lock screw to adjust the tilt angle [0 °to 100°].
2). Loosen No.2 lock screw to adjust the pan angle [0°to 360°].
3). Loosen No.3 lock screw to rotate the camera [0°to 360°].
4). Tighten the lock screws.
0°to 360°
1
2
3
0°to 100°
0°to 360°
Adjust the Surveillance AngleFigure 2-5
Supplied WrenchFigure 2-6

Network Bullet Camera·Quick Start Guide
18
18
Wall Mounting with a Junction Box2.3
Before you start:
A junction box is not included in the package. If you choose this
mounting type, you have to prepare a junction box in advance. Note
that the size and screw holes of a junction box should match those of
the camera.
Bracket Bottom OverviewFigure 2-7
Steps:
1. Paste the drill template on the desired mounting place on wall.
2. Drill the screw holes for the junction box according to Hole 2 of
the drill template. See Figure 2-3.
(Optional) If you want to route cables through the wall, cut a hole
according to Hole A of the drill template. See Figure 2-3.
3. Align the screw holes of the junction box to the drill template, and
fix the junction box to the wall with screws.

Network Bullet Camera·Quick Start Guide
19
19
4. Route the cables.
5. Fix the camera to the junction box with screws.
6. Adjust the surveillance angle. See step 4 in Section 2.2.
7. Install the water-proof jacket. See Section 2.5.
Wall Drill
Template
Junction
Box Camera
Bracket
Screw Hole 2
Installation with a Junction BoxFigure 2-8
Wall Mounting with a Gang Box2.4
Before you start:
If you choose this mounting type, you have to prepare a gang box
and an adapter plate in advance.
Note that the size and screw holes of the adapter plate should match
those of the camera and the gang box at the same time. For the size
and screw holes of the camera bracket, see Figure 2-7.