HIK VISION DS-3E1 P Series User manual

100 Mbps PoE Switch
Quick Start Guide
UD18592B

Legal Informaon
©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights
reserved.
About this Manual
The Manual includes instrucons for using and managing the
Product. Pictures, charts, images and all other informaon
hereinaer are for descripon and explanaon only. The
informaon contained in the Manual is subject to change,
without noce, due to rmware updates or other reasons. Please
nd the latest version of this Manual at the Hikvision website
( hps://www.hikvision.com/ ).
Please use this Manual with the guidance and assistance of
professionals trained in supporng the Product.
Trademarks
and other Hikvision's trademarks
and logos are the properes of Hikvision in various jurisdicons.
Other trademarks and logos menoned are the properes of
their respecve owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS
MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH
ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A
PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT
YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,
WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING
NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES
FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE
ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK,
HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL
APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR
ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN
A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD
PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF
i

PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA
PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE
THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE
DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS
DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF
CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE
CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE
NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS
ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND
THE APPLICABLE LAW, THE LATER PREVAILS.
ii

Regulatory
FCC
Please take that changes or not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide
reasonable against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
manual, may cause harmful interference to radio
of this equipment in a
area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
FCC
This device complies with part 15 of the FCC Rules. is
subject to the following two
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired
EU Conformity Statement
This product and - if applicable - the supplied accessories
too are marked with "CE" and comply therefore with the
applicable harmonized European standards listed under
the EMC 2014/30/EU, the RoHS 2011/
65/EU.
2012/19/EU (WEEE Products marked with this
symbol cannot be disposed of as unsorted municipal waste
in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated
points. For more see:
www.recyclethis.info .
2006/66/EC This product contains a
that cannot be disposed of as unsorted municipal
waste in the European Union. See the product
for The
is marked with this symbol, which may include
to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the to your
supplier or to a designated point. For more
see: .
iii

Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards
requirements.
iv

Preface
Applicable Models
This manual is applicable to DS-3E1XXXP series switches.
Symbol Convenons
The symbols that may be found in this document are dened as
follows.
Symbol Descripon
Danger Indicates a hazardous situaon which, if not avoided,
will or could result in death or serious injury.
Cauon
Indicates a potenally hazardous situaon which, if
not avoided, could result in equipment damage, data
loss, performance degradaon, or unexpected
results.
Note Provides addional informaon to emphasize or
supplement important points of the main text.
v

Safety Instrucon
Danger
•This is a class A product and may cause radio interference in
which case the user may be required to take adequate
measures.
•Ensure that your devices powered via the PoE port have their
shells protected and re-proofed, because the switches are not
compliant with the Limited Power Source (LPS) standard.
•In the use of the product, you must be in strict compliance with
the electrical safety regulaons of the naon and region.
•The socket-outlet shall be installed near the device and shall be
easily accessible.
•The device must be connected to an earthed mains socket-
outlet.
•Install the device according to the instrucons in this manual.
• indicates hazardous live and the external wiring connected
to the terminals requires installaon by an instructed person.
•Keep body parts away from fan blades. Disconnect the power
source during servicing.
•Never place the device in an unstable locaon. The device may
fall, causing serious personal injury or death.
•This device is not suitable for use in locaons where children
are likely to be present.
•CAUTION: Risk of explosion if the baery is replaced by an
incorrect type.
•Improper replacement of the baery with an incorrect type
may defeat a safeguard (for example, in the case of some
lithium baery types).
•Do not dispose of the baery into re or a hot oven, or
mechanically crush or cut the baery, which may result in an
explosion.
•Do not leave the baery in an extremely high temperature
surrounding environment, which may result in an explosion or
the leakage of ammable liquid or gas.
•Do not subject the baery to extremely low air pressure, which
may result in an explosion or the leakage of ammable liquid
or gas. Dispose of used baeries according to the instrucons.
Cauon
•CAUTION: Double pole/Neutral fusing. Aer operaon of the
fuse, parts of the device that remain energized might represent
a hazard during servicing.
•The device has been designed, when required, modied for
connecon to an IT power distribuon system.
•This device is suitable for mounng on concrete or other non-
combusble surface only.
•The venlaon should not be impeded by covering the
venlaon openings with items, such as newspapers, table-
cloths, curtains, etc. The openings shall never be blocked by
placing the device on a bed, sofa, rug or other similar surface.
vi

•No naked ame sources, such as lighted candles, should be
placed on the device.
•The device shall not be exposed to dripping or splashing and
that no objects lled with liquids, such as vases, shall be placed
on the device.
•Burned ngers when handling the cover area of the device.
Wait one-half hour aer switching o before handling the
parts.
•CLASS 1 LASER PRODUCT
vii

1 Introducon
1.1 Product Introducon
DS-3E1XXXP series switches (hereinaer referred to as "the
device") are layer 2 PoE switches, providing advanced PoE power
supply technology on the basis of high-performance access. The
switches support client management, network topology
management, link aggregaon, port management and so on. The
switches are suitable for small-scale LAN device access.
1.2 Packing List
DS-3E1X05/09P Series DS-3E1318/26P Series
Switch × 1 × 1
Power Adapter × 1 -
AC Power Cord × 1 × 1
Screw - × 4
L-Shaped Bracket - × 2
Quick Start Guide × 1 × 1
1.3 Appearance
Dierent models of devices may have dierent appearances. The
following pictures are only for illustraon.
Front Panel
Figure 1-1 DS-3E1105P Series
Note
The front panel of DS-3E1309P switch is similar to that of
DS-3E1105P, with dierences on 8 100Mbps PoE RJ45 ports, and
that No.9 port is gigabit RJ45 port.
Figure 1-2 DS-3E1318P Series
Note
The front panel of DS-3E1326P switch is similar to that of
DS-3E1318P, with dierences on 24 100Mbps PoE RJ45 ports, 24
LINK/ACT, and 24 PoE indicators.
1

Rear Panel
Figure 1-3 DS-3E1X05/09P Series
Figure 1-4 DS-3E1318/26P Series
Port/Indicator Descripon
Indicator/Port Descripon
PoE-MAX Indicator
•Solid /Flashing: The output power of the switch
will reach the upper limit. The power supply may
be abnormal if more devices are connected.
•Unlit: The switch provides power supply to PD
normally.
PWR Indicator
•Solid: The switch is powered on normally.
•Unlit: No power supply connected or power
supply is abnormal.
LINK/ACT Indicator
•Solid: The port is connected.
•Flashing: The port is transming data.
•Unlit: The port is disconnected or connecon is
abnormal.
PoE Indicator
•Solid: The switch provides power supply to PD
normally.
•Unlit: The switch is disconnected to PD, or
provides power supply to PD abnormally.
G1/G2 Port
Indicator
•Solid: The gigabit SFP ber opcal port is
connected.
•Flashing: The gigabit SFP ber opcal port is
transming data.
•Unlit: No gigabit SFP ber opcal port connected
or connecon is abnormal.
100Mbps PoE RJ45
Port Used for PD devices connecon via network cables.
100Mbps RJ45 Port Used for other devices connecon via network
cables.
Gigabit Combo
•When connected to a network cable, the combo
is a RJ45 port. When plugged into with an opcal
module and connected to an opcal ber, the
combo funcons as a ber opc port.
•When connected to both the network cable and
opcal ber at the same me, the port works as a
ber opc port.
2

Grounding Terminal Used for connecng to the grounding cable to
protect the switch from lightning.
Power Supply Use the aached power cord to connect the switch
to socket.
2 Installaon
Please select the appropriate installaon method according to
the actual needs.
Before You Start
•Ensure that the desktop or rack is stable and rm enough.
•Keep the room well-venlated. Keep at least 10 cm distance
around the device for heat dissipaon.
•Keep at least 1.5 cm vercal distance between two adjacent
devices for rack-mount installaon.
2.1 Desk-Mounted Installaon
Place the device on the desk.
2.2 Wall-Mounted Installaon
Steps
1. Check the distance between the two hanging holes on the rear
cover of the device.
2. Insert two M4 screws into the wall.
Note
•Please prepare two M4 screws.
•Ensure that the distance between the two screws equals
that between the two hanging holes.
•Set aside at least 4 mm screws outside the wall.
3. Align the hanging holes with screws, and hang the device on
the screws.
Figure 2-1 Wall-Mounted Installaon
2.3 Rack-Mounted Installaon
Steps
1. Check the grounding and stability of the rack.
2. Use the aached screws to x the two L-shaped brackets to the
sides of the switch.
3

Figure 2-2 Fix L-Shaped Brackets
3. Place your switch on the rack, x it to the rack with self-
prepared screws to stably install your switch.
Figure 2-3 Fix to the Rack
3 Grounding
3.1 Connecng the Grounding Cable
Grounding is used to quickly release overvoltage and overcurrent
induced by lightening for switch, and to protect personal safety.
Select the appropriate grounding method according to your
needs.
3.1.1 With Grounding Bar
If a grounding bar is available at the installaon site, follow the
steps below.
Steps
1. Connect one end of the grounding cable to the binding post on
the grounding bar.
2. Connect the other end of the grounding cable to the grounding
terminal of the device and x the screw.
Figure 3-1 Grounding with Grounding Bar
3.1.2 Without Grounding Bar
If there is no grounding bar but the earth is nearby and the
grounding body is allowed to be buried, follow the steps below.
Steps
1. Bury an angle steel or steel pipe (≥ 0.5 m) into the mud land.
4

2. Weld one end of the grounding cable to the angle steel or steel
pipe and embalm the welding point via electroplang or
coang.
3. Connect the other end of the grounding cable to the grounding
terminal.
Figure 3-2 Grounding with Angle Steel
3.2 Connecng RJ45 Port
Use a network cable to connect the device to the RJ45 port of a
peer device such as network camera, NVR, switch, etc.
Figure 3-3 RJ45 Port Connecon
3.3 Connecng SFP Opcal Module
Connecng SFP opcal module is supported when the device has
a ber opc port or a combo.
When connected to a network cable, the combo is a RJ45 port.
When plugged into with an opcal module and connected to an
opcal ber, the combo funcons as a ber opc port.
When connected to both the network cable and opcal ber at
the same me, the port works as a ber opc port.
Steps
Cauon
•Single-Mode opcal module needs to be paired.
•Do not bend ber opc (curvature radius ≥ 10 cm) overly.
•Do not look directly at ber opc connector because the laser
is harmful to eyes.
1. Connect the two paired SFP opcal modules with an opcal
ber.
5

2. Hold the SFP opcal module from one side, and smoothly plug
it into the device along with the SFP port slot unl the opcal
module and the device are closely aached.
3. Aer powering on the device, check the status of LINK/ACT
indicator. If the indicator is lit, the link is connected. If the
indicator is unlit, the link is disconnected. Check the line, and
make sure peer devices have been started.
4 Powering on the Device
Please use the aached power cord in package to power on the
device.
Before powering your switch, make sure that:
•The operang power supply is compliant with rated input
standard.
•Port cables and grounding cables are correctly connected.
•If there is outdoor cabling, connect a lightning rod and
lightening arrester to the cable.
Cauon
PoE power supply line and strong wire cannot be wired together,
otherwise PD equipment or switch ports will be burnt.
5 Device Management
The device can be congured and managed through iVMS-4200
soware, mainly including network parameter conguraon, port
conguraon, link aggregaon conguraon, network topology
display and so on.
Note
•This chapter will briey introduce the device management
through the iVMS-4200 soware. For other funcons, please
refer to User Manual of iVMS-4200 Client Soware.
•All pictures in this manual are for illustraon only, and the
specic interface is subject to the actual interface.
5.1 Acvang Devices
For the inacve devices, you are required to create a password to
acvate them before they can be added to the soware and work
properly.
Before You Start
Make sure the device to be acvated is connected to the network
and is in the same subnet with the PC running the client.
Steps
Note
This funcon should be supported by the device.
1. Enter the Device Management page.
2. Click Device tab on the top of the right panel.
6

3. Click Online Device to show the online device area at the
boom of the page.
The searched online devices are displayed in the list.
4. Check the device status (shown on Security Level column) and
select an inacve device.
Figure 5-1 Online Inacve Device
5. Click Acvate to open the Acvaon dialog.
6. Create a password in the password eld, and conrm the
password.
Cauon
The password strength of the device can be automacally
checked. We highly recommend you change the password of
your own choosing (using a minimum of 8 characters, including
at least three kinds of following categories: upper case leers,
lower case leers, numbers, and special characters) in order to
increase the security of your product. And we recommend you
change your password regularly, especially in the high security
system, changing the password monthly or weekly can beer
protect your product.
Proper conguraon of all passwords and other security
sengs is the responsibility of the installer and/or end-user.
7. Click OK to acvate the device.
5.2 Adding Devices
The client provides various device adding modes including IP/
domain, IP segment, cloud P2P, ISUP protocol, and HiDDNS. The
client also supports imporng mulple devices in a batch when
there are large amount of devices to be added. The secon only
introduces one mode, namely, adding a detected online device.
Steps
1. Enter the Device Management module.
2. Click Device tab on the top of the right panel.
3. Click Online Device to show the online device area.
The searched online devices are displayed in the list.
4. Select an online device in the Online Device area, and click
Add to open the device adding window.
Note
For the inacve device, you need to create the password for it
before you can add the device properly. For detailed steps,
refer to Acvang Devices.
5. Enter the required informaon.
Name
Enter a descripve name for the device.
IP Address
Enter the device's IP address. The IP address of the device is
obtained automacally in this adding mode.
7

Port
You can customize the port number. The port number of the
device is obtained automacally in this adding mode.
User Name
By default, the user name is admin.
Password
Enter the device password.
Cauon
The password strength of the device can be automacally
checked. We highly recommend you change the password of
your own choosing (using a minimum of 8 characters,
including at least three kinds of following categories: upper
case leers, lower case leers, numbers, and special
characters) in order to increase the security of your product.
And we recommend you change your password regularly,
especially in the high security system, changing the
password monthly or weekly can beer protect your
product.
Proper conguraon of all passwords and other security
sengs is the responsibility of the installer and/or end-user.
6. Check Synchronize Time to synchronize the device me with
the PC running the client aer adding the device to the client.
7. Click Add.
6 Get More Informaon
Scan the QR code below for iVMS-4200 soware operaons.
8