HIK VISION DY5 Series User manual

Network Positioning System
Quick Start Guide

Network Positioning System·Quick Start Guide
i
Quick Start Guide
COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the
properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries
(hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be
“the Manual”) cannot be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of Hikvision. Unless
otherwise stipulated, Hikvision does not make any warranties, guarantees or
representations, express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to Network Positioning System.
The Manual includes instructions for using and managing the product. Pictures, charts,
images and all other information hereinafter are for description and explanation only.
The information contained in the Manual is subject to change, without notice, due to
firmware updates or other reasons. Please find the latest version in the company
website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision
in various jurisdictions. Other trademarks and logos mentioned below are the properties
of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED,
WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL
FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN
NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE
LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION
WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR

Network Positioning System·Quick Start Guide
ii
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM
CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY
RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN
YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR
USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW,
THE LATER PREVAILS.
0505001080517

Network Positioning System·Quick Start Guide
3
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2015/35/EU, the EMC
Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Network Positioning System·Quick Start Guide
iv
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
Adopt the power adapter which can meet the safety extra low voltage (SELV)
standard. The power consumption cannot be less than the required value.
Do not connect several devices to one power adapter as an adapter overload may
cause over-heating and can be a fire hazard.
When the product is installed on a wall or ceiling, the device should be firmly fixed.
To reduce the risk of fire or electrical shock, do not expose the indoor used product
to rain or moisture.
This installation should be made by a qualified service person and should conform to
all the local codes.
Install blackouts equipment into the power supply circuit for convenient supply
interruption.
If the product does not work properly, contact your dealer or the nearest service
center. Never attempt to disassemble the product yourself. (We shall not assume
any responsibility for problems caused by unauthorized repair or maintenance.)
Cautions
If the network positioning system fails to synchronize local time with that of the
network, you need to set up network positioning system time manually. Visit the
network positioning system (via web browser or client software) and enter system
settings interface for time settings.
Make sure the power supply voltage is correct before using the product.
Do not drop the product or subject it to physical shock. Do not install the product on
vibratory surface or places.
Do not expose it to high electromagnetic radiating environment.
Do not aim the lens at the strong light such as sun or incandescent lamp. The strong
light can cause fatal damage to the product.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.

Network Positioning System·Quick Start Guide
v
The sensor may be burned out by a laser beam, so when any laser equipment is
being used, make sure that the surface of the sensor not be exposed to the laser
beam.
For working temperature, refer to the specification manual for details.
To avoid heat accumulation, good ventilation is required for a proper operating
environment.
While shipping, the product should be packed in its original packing.
Use the provided glove when open up the product cover. Do not touch the product
cover with fingers directly, because the acidic sweat of the fingers may erode the
surface coating of the product cover.
Use a soft and dry cloth when clean inside and outside surfaces of the product cover.
Do not use alkaline detergents.
Improper use or replacement of the battery may result in hazard of explosion. Use
the manufacturer recommended battery type.

Network Positioning System·Quick Start Guide
vi
Table of Contents
1 Overview...................................................................................................... 7
1.1 Introduction ........................................................................................................ 7
1.1.1 Overview of DY5xxx Series Network Positioning System ............................. 7
1.1.2 Overview of DY7xxx Series Network Positioning System ............................. 8
1.1.3 Overview of DY9xxx Series Network Positioning System ........................... 10
1.2 Cable Descriptions ............................................................................................ 11
1.3 Alarm Input/Output .......................................................................................... 12
2 Installation ................................................................................................. 13
2.1 Installing DY9xxx Network Positioning System ...................................................... 13
2.1.1 Installing DY9xxx Series Laser Network Positioning System (Type III and Type IV)
................................................................................................................................. 13
2.1.2 Installing DY9xxx Series IR Network Positioning System (Type II).................... 18
2.1.3 Installing DY9xxx Series Network Positioning System (Type I)......................... 21
2.2 Installing DY7xxx Network Positioning System ...................................................... 21
2.3 Installing DY5xxx Network Positioning System ...................................................... 21
3 Setting the Positioning System over the LAN.............................................. 22
3.1 Wiring.................................................................................................................... 22
3.2 Activating the Positioning System.......................................................................... 22
3.2.1 Activation via Web Browser ............................................................................ 23
3.2.2 Activation via SADP Software .......................................................................... 24
3.3 Modifying the IP Address....................................................................................... 25
4 Accessing via Web browser ........................................................................ 27
5 Operating via Hik-Connect App .................................................................. 29
5.1 Enable Hik-Connect Service on Positioning System ............................................... 29
5.1.1 Enable Hik-Connect Service via SADP Software .............................................. 29
5.1.2 Enable Hik-Connect Service via Web Browser................................................. 30
5.2 Hik-Connect Setup ................................................................................................. 30
5.3 Adding Positioning System to Hik-Connect............................................................ 31
5.4 Initializing the Memory Card ................................................................................. 32

Network Positioning System·Quick Start Guide
7
1Overview
1.1 Introduction
The network positioning system has three series:
DY5xxx Series
DY7xxx Series
DY9xxx Series
1.1.1 Overview of DY5xxx Series Network Positioning System
Shield
(Auxiliary
Light Side)
Shield
(Camera Side)
Wiper
Main Body
Base
306
212
165
Unit: mm
Figure 1-1 Dimensions of DY5xxx Series Network Positioning System (Type I)
167
167
132
132
4-Φ9
Unit: mm
Figure 1-2 Bottom View of DY5xxx Series Network Positioning System (Type I)

Network Positioning System·Quick Start Guide
8
306
212
165
35
Unit: mm
Shock-absorbing
pad
Shield
(Auxiliary
Light Side)
Main body
Wiper
Shield
(Camera
Side)
Base
Figure 1-3 Dimensions of DY5xxx Series Mobile Network Positioning System (Type II)
Unit: mm
134
4-Φ9
140
140
175
175
Figure 1-4 Dimensions of Shock-absorbing Pad for DY5xxx Series Mobile Network
Positioning System (Type II)
1.1.2 Overview of DY7xxx Series Network Positioning System
Unit: mm
396
188
377.5
218
IR
Base
Main Body
Shield
Figure 1-5 Dimensions of DY7xxx Series IR Network Positioning System (Type I)

Network Positioning System·Quick Start Guide
9
218
377.5
188 396
IR
Shield
Wiper
Main Body
Base
Unit: mm
Figure 1-6 Dimensions of DY7xxx Series IR Network Positioning System (Type I with
Wiper)
Unit: mm
396
188
377.5
218
Shield
Main Body
Base
Figure 1-7 Dimensions of DY7xxx Series Network Positioning System (Type II)

Network Positioning System·Quick Start Guide
10
1.1.3 Overview of DY9xxx Series Network Positioning System
390
180
491
Unit: mm
Shield
390
180
491
Unit: mm
Wiper
Main Body
Base
Figure 1-8 Dimensions of DY9xxx Series Network Positioning System (Type I)
Unit: mm
460
180
491
Wiper
Shield
Main Body
Base
IR Module
Figure 1-9 Dimensions of DY9xxx Series IR Network Positioning System (Type II)
251
Unit: mm
360
508
180
Housing
Wiper
Main Body
Base
Figure 1-10 Dimensions of DY9xxx Series Laser Network Positioning System (Type III)

Network Positioning System·Quick Start Guide
11
Unit: mm
505
256 334
180
Shield
Wiper
Main Body
Base
Figure 1-11 Dimension of DY9xxx Series Laser Network Positioning System (Type IV)
Unit:mm
116.7
116.7
Φ165
Φ180
4-Φ9
Figure 1-12 Bottom View of DY9xxx Series Network Positioning System
1.2 Cable Descriptions
Cables of network positioning system are shown in Figure 1-13. The cables are
distinguished by different colors. Refer to the labels attached on the cables for
identification.
Notes:
The cables vary depending on different positioning system models.
Make sure the positioning system is power-off before you connect the cables.

Network Positioning System·Quick Start Guide
12
Network Cable
Audio Cable
Alarm Cable
Video Cable
RS-485 Cable
Power Cord
Figure 1-13 Cables
1.3 Alarm Input/Output
Network positioning system can be connected with alarm input (0 to 5 VDC) and alarm
output as shown in Figure 1-14. The alarm provides the relay output (no voltage), and
the external power supply is required when it connects to the alarm device.
JQC-3FG
Relay
30VDC
GND OUT
L N
～220V AC
Relay Output
(10A 250VAC )
Diagram (left) Diagram (right)
1A
OUT(n)
OUT(n)
+
-
DC
DC Load
Relay Output
Positioning System OUT(n)
OUT(n)
Positioning System
Figure 1-14 Alarm Output Connection
For DC power supply (left diagram), the input voltage must be no more than 30 VDC,
1A.
For AC power supply, the external relay must be used (right diagram) to prevent
damages to the positioning system and avoid risk of electric shock.
Note:
Alarm input/output function varies depending on different positioning system models.

Network Positioning System·Quick Start Guide
13
2Installation
Before you start:
Check the package contents and make sure that the device in the package is in good
condition and all the assembly parts are included.
Notes:
Do not power the positioning system up until the installation is finished. To ensure
safety of personnel and equipment, all the installation steps should be done with
power supply off.
The positioning system is much heavier than the normal camera, and it strongly
demands for load-bearing and stability of the upholder. It’s highly recommended to
install the system to the upholder directly.
If you need to install the positioning system to the bracket, refer to bottom view of
the positioning system as shown in section 1.1 Introduction to select the bracket.
The load-bearing and anti-shake capabilities must be fully taken into consideration.
2.1 Installing DY9xxx Network Positioning System
2.1.1 Installing DY9xxx Series Laser Network Positioning System (Type III
and Type IV)
Steps:
1. Fix the positioning system.
1) Fix the positioning system onto the bracket pedestal with the supplied M8*30
screws as shown in Figure 2-1 and Figure 2-2.
Figure 2-1 Fix the Positioning System (Type III)

Network Positioning System·Quick Start Guide
14
Figure 2-2 Fix the Positioning System (Type IV)
Note:
The thickness of the pedestal steel plate should be more than 5 mm.
2) Connect the corresponding cables.
2. Adjust the laser.
1) Observe the location of laser spot in the image. Adjust the zoom ratio of the lens
to a large value, the laser supplementary lighting system will adjust the light
according to the zoom ratio, and then you can see the laser spot on the live view
image.
If the spot location is the same as shown in figure A, you can skip the step of
adjusting the laser; if not, you need to adjust the laser.
ABC
Figure 2-3 Laser Spot Location
Note:
You can zoom in/out to adjust the size of the laser spot. The spot location shown in
figure A is the optimum location.
2) For type III camera, loosen the inner hexagon screws with the wrench and open
the lid of housing.

Network Positioning System·Quick Start Guide
15
Inner Hexagon Screw
Inner Hexagon Screw
Figure 2-4 Open the Lid of Housing (Type III)
For type IV camera, loosen the screws of sunshield and top cover. Take down the
sunshield and top cover.
M4 Cross
Screw
Sunshield
Top Cover
M4 Torx
Needle Screw
Figure 2-5 Open the Sunshield of Housing (Type IV)
3) Insert the memory card into the memory card slot.

Network Positioning System·Quick Start Guide
16
Memory Card
Figure 2-6 Insert the Memory Card (Type III)
Memory Card
Memory Card
DarkFighterX
Figure 2-7 Insert the Memory Card (Type IV)
4) Slightly adjust the control screws for the laser according to the actual situation.
Tilting Adjustment
Screw
Eccentric Wheel Panning Fastening
Screw
Figure 2-8 Adjust the Laser (Type III)

Network Positioning System·Quick Start Guide
17
Eccentric Wheel
Tilting Adjustment
Screw Panning
Fastening Screw
Figure 2-9 Adjust the Laser (Type IV)
Notes:
Panning Adjustment: Loosen the two panning fastening screws, rotate the
eccentric wheel to adjust the laser spot in the horizontal direction, and fasten the
screws after adjusting.
Tilt Adjustment: Tighten or loosen the tilting adjustment screw to adjust the
position of the laser spot in the vertical direction.
3. Restore the housing and tighten the screws for waterproof.
Figure 2-10 Restore the Housing (Type III)

Network Positioning System·Quick Start Guide
18
Figure 2-11 Restore the Housing (Type IV)
4. Connect the corresponding cables and turn the power on; the system will do the
self-test automatically.
2.1.2 Installing DY9xxx Series IR Network Positioning System (Type II)
Steps:
1. Install the IR module.
1) Align the screw holes on the IR bracket with the screw holes on the housing as
shown in Figure 2-12. Insert and tighten the two M4*10 screws to secure the
bracket.
Figure 2-12 Secure the IR Bracket
2) Loosen and remove the screws on the top of IR module. Align the screw holes on
the IR module with the screw holes on the IR bracket, and secure the IR module
to the IR bracket with the screws.

Network Positioning System·Quick Start Guide
19
Figure 2-13 Secure the IR Module
3) Align the buckles to the screw holes on the IR bracket and secure them with two
M4*10 screws.
Note:
The buckles are fixed with the cable by default.
Figure 2-14 Secure the Cables to IR Bracket
2. Route the cables of IR modules.
1) Pull out the two original plugs from the housing.
2) Loosen the nuts on the water-proof cable plugs.
3) Route the IR module cables through the cable holes on the housing respectively.
4) Rotate the locking plug clockwise and tightly to the housing.
5) Insert the cables to the housing as much as possible, and fasten the water-proof
cable nuts with a wrench.
Locking Plug
Water-proof Cable Nut
Figure 2-15 Route the Cables