Hiltron security XM Series User manual

!Antishock sensor with sensitivity adjustment
!Settaggi effettuabili direttamente dalla centrale
!Protection tamper anti-opening
!Low battery warning with LED
!Supply: 2 AAA batteries (mini-stylus)
!Radio system bidirectional
!Signaling LED alarm
!Maximum absorption 35mA
!Signal coverage area: about 100mt.
!Life battery: about 1 anno
!Work frequency 433,92Mhz multi-chamnnel
(8 channels) bidirectional
!Operating temperature 0°C ÷ +50°C
!IP protection degree IP40
!Degree of security 1
!Environmental class 2
!Dimensions (LxAxP) 100x21x31mm
!Compliant with the standard CEI EN 50131-1
XMR200S
XMR200SM - XMR200SA
Magnetic contact via radio SÉRIE XM
1
INSTALLATION
!Secure the sensor base with the
two supplied screws or using a
double-sided adhesive holder.o.
!The internal magnetic contact is
located on the side near the
tamper button.
!Mount the magnet
(XMR series magnets only) at a
maximum distance of about
15mm.To connect magnetic
contacts or other sensors to the IN
input on the terminal block or to
the TAMPER input, do not use
excessively long cables (no more
than 50 cm).
!To enable the Tamper input on the terminal board, it is necessary to cut the jumper JP1 located near
the fixing screw.
!Insert two AAA batteries (ministyle) respecting the indicated polarity: when switched on, the three
LEDs emit two flashes, followed by a flash of the green LED which indicates that the code is being
sent to the control unit.
!Close the XMR200S using the supplied screw.
NOTE: The use of wireless devices is strongly influenced by external factors, such as radio links
and other existing wireless devices. The control unit communicates the level of signal
received by each sensor, and where one of these should be low, we recommend a wired
wiring.
Pb
Lead free
RoHS
compliant
RAEE
security
Made in Italy
BT2014/35/UE
EMC2014/30/UE
INSTALLATION
NC protection circuit24h
(short wires)
NC magnetic contact
(Long strands)
Mount on wood onlyaluminum
or non-ferrous materials.
WINDOW
JAMB

2
XMR200S - XMR200SM - XMR200SA - User manual
822ADE-1.01
XMR200S PARAMETERS TABLE
The following table illustrates the main functions of Type 015
COLLEGAMENTI
LOW BATTERY SIGNAL
The flashing of the LEDs on each XMR device indicate the low battery:
flashing GREEN LED alternating with YELLOW LED = BATTERY CHARGED
flashing RED LED alternating with YELLOW LED = BATTERY ALMOST LOWflashing RED LED +
YELLOW LED + GREEN LED = LOW BATTERY (REPLACE).
security
+
-
S2
LDS2
LDS1
LDS3
S4
JP1
S3
S3
B2
B1
S1
REMOVE THE JUMPER
FOR ACTIVATION
24H EXTERNAL JP1
S2
-
IN
24H
S2
LDS2
LDS1
LDS3
S4
JP1
S3
S3
B2
B1
S1
JP1
CLOSE THE JUMPERF
OR ACTIVATION24H
INTERNAL CONTACT
MAGNETIC
COM
IN
24H
COM
CONTACT
MAGNETIC
S2
S4
S3
B1 / B2
JP1
LDS2
LDS1
LDS3
SHOCK SENSOR
MAGNETIC SENSOR
BATTERY HOUSING
JUMPER FOR TAMPER ACTIVATION
TAMPER
GREEEN LED (TX)
RED LED (TX / LOW BATTERY)
YELLOW RED (RX)
CENTRAL ASSOCIATION BUTTON
S1
01
FUNCTION
02
03
04
05
07
08
09
10
00
DISCONNECTION
CONNECTION
CONN./DISCONN.
SILENT CONNECTION
SIL. CONN./DISCONN.
ALARM STOP
IMMEDIATE ZONE
DELAYED ZONE
24
NONE
H
ENABLING01
PARAMETERS
DESCRIPTION02
SERIAL03
TAMPER06
07
SENSITIVTY11
SYSTEM
AREA
15
FUNCTION
16
17
INSTANT GONG22
LOGICAL OUTPUT29
NA\NC POLARITY
/ INPUT 24h
YES / NO
YES / NO
YES / NO
LED
SHOCK SENSOR
32
SENS. SHOCK
33
34
ALL. LINK RF35
INPUTS36
STATE / EVENT37
ON / OFF
YES / NO
1 / 8
0-Disactive
2-Input
1-24H
Internal
External
Both of them