Hirschmann EAGLE One User manual

Installation EAGLE One
Release 03 07/2014
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Firewall
EAGLE One

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2014 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Installation EAGLE One 040-036-001-03-0714 - 10.07.2014

Installation EAGLE One
Release 03 07/2014 3
Contents
Safety instructions 5
About this manual 16
Key 16
1 Description 17
1.1 General description 17
1.2 Device name and product code 18
1.3 Combination options 22
1.4 Device view 23
1.5 Power supply 24
1.6 Ethernet ports 24
1.6.1 10/100 Mbit/s twisted pair port 24
1.6.2 100 Mbit/s F/O port 25
1.7 Display elements 25
1.7.1 Device state 25
1.7.2 Additional status information 26
1.7.3 Port state 26
1.8 Management interfaces 26
1.8.1 V.24 interface (external management) 26
1.8.2 ACA21-USB interface 27
1.9 Input/output interfaces 28
1.9.1 Signal contact 28
1.9.2 Digital input 28
2 Installation 29
2.1 Overview 29
2.2 Check the contents of the package 29
2.3 Installing and grounding the device 29
2.3.1 Installing the device onto the DIN rail 30
2.3.2 Mounting on a vertical flat surface 30
2.3.3 Grounding the device 31
2.4 Connecting the terminal blocks 31
2.4.1 Connecting the power supply and signal lines 32
2.4.2 Wiring the digital input (optional) 33
2.5 Operating the device 33
2.6 Connecting data cables 34

4Installation EAGLE One
Release 03 07/2014
3 Configuration 35
3.1 Making basic settings 35
3.2 Firewall and VPN functions 35
3.2.1 Firewall functions 35
3.2.2 VPN functions 36
3.3 Operating modes 36
3.3.1 Delivery state 36
3.3.2 Transparent mode 37
3.3.3 Router mode 37
3.3.4 PPPoE mode 37
3.4 Starting Configuration 37
4 Monitoring the ambient air temperature 39
5 Maintenance and service 40
6Disassembly 41
7 Technical data 42
A Further Support 51

Installation EAGLE One
Release 03 07/2014 5
Safety instructions
General safety instructions
You operate this device with electricity. The proper and safe operation of
this device depends on proper handling during transportation, proper
storage and assembly, and conscientious operation and maintenance
procedures. Improper use of this device is associated with the risk of
personal injury or property damage.
Read this documentation as well as the safety instructions and
warnings before connecting any cables.
Never start operation with damaged components.
The device does not contain any service components. If the device is
not functioning correctly, or if it is damaged, turn off the power supply
and return the device to Hirschmann for inspection.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Intended usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation EAGLE One
Release 03 07/2014
See “Technical data” on page 42.
Connect to the product only components suitable for the requirements
of the specific application case.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected shielded twisted pair cable is connected
to the ground connector on the front panel as a conductor.
Working voltage
The working voltage is electrically isolated from the housing.
Connect only a working voltage that corresponds to the type plate of
your device.
Every time you connect the electrical conductors, make sure that the
following requirements are met:
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device
(e.g., a switch or a plug). This disconnecting device is clearly
identified. So in the case of an emergency, it is clear which
disconnecting device belongs to which power supply cable.
The electrical wires are voltage-free.
The power supply is Class 2 compliant.
The working voltage inputs are designed for operation with safety
extra-low voltage. Connect only SELV circuits with voltage
restrictions in line with IEC/EN 60950-1 to the working voltage
connections.
Supply with AC voltage:
A fuse is located in the outer conductor of the power supply.
The neutral conductor is on ground potential. Otherwise, a fuse is
also located in the neutral conductor.
Regarding the properties of this fuse: See “General technical data”
on page 42.

Installation EAGLE One
Release 03 07/2014 7
Supply with DC voltage:
A fuse suitable for DC voltage is located in the plus conductor of the
power supply.
The minus conductor is on ground potential. Otherwise, a fuse is
also located in the minus conductor.
Regarding the properties of this fuse: See “General technical data”
on page 42.
The wire diameter of the power supply cable is at least 1 mm²
(North America: AWG16) on the working voltage input.
The cross-section of the protective conductor is the same size as
or bigger than the cross-section of the power supply cables.
The power supply cables used are permitted for the temperature
range required by the application case.
Relevant for North America:
Use 60/75 or 75 °C copper (Cu) wire only.
Internal fuses are triggered solely in the case of a detected error in the
device. In case of damage or malfunction of the device, turn off the
working voltage and return the device to the plant for inspection.
Input/output interfaces
Every time you connect the electrical conductors, make sure that the
following requirements are met:
The electrical wires are voltage-free.
The connected voltage is limited by a current limitation device or a
fuse.
Observe the electrical threshold values for the signal contact.
See “General technical data” on page 42.
Observe the electrical threshold values for the digital input.
See “Digital input” on page 44.
Installation site requirements
Verify that there is at least 4 in (10 cm) of space above and below the
device.
Verify that there is at least 0.8 in (2 cm) of space on the right and left
sides of the device.
Install the device in a fire protected enclosure according to
EN 60950-1.

8Installation EAGLE One
Release 03 07/2014
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
Install the device in the vertical position.
At ambient temperatures > 140 °F (60 °C):
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
LED or laser components
LED or LASER components according to IEC 60825-1 (2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2004/108/EC (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
You find more information on technical and industry standards here:
“Technical data” on page 42

Installation EAGLE One
Release 03 07/2014 9
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
Relevant for use in North America
Use this device solely in Class 2 Circuits.
Relevant for USE in Hazardous Locations Class I Division 2,
Groups A, B, C, D
The relay connections and the USB connetions are to be installed and
used within their Entity Parameters as per Control Drawing
000174247DNR – details see the next two pages.

10 Installation EAGLE One
Release 03 07/2014
CONTROL DRAWING to EAGLEONE and TOFINOXE series for Use in Hazardous Locations Class I Division 2, Groups A, B, C, D Rev. 0 Document No.: 000174247DNR Page 1/2
MSP30 / MSP32
Class I Division 2
Groups A, B, C, D Hazardous Location
Ordinary Location, Non-Hazardous Area,
Nonexplosive Atmosphere
1 2 3 4 4 3 2 1
The earth conductor must be
at least of the same wire size (mm² or AWG) as the supply conductors.
Nonincendive field wiring parameters:
THE RELAY TERMINALS ARE DEPENDENT UPON THE FOLLOWING ENTITY PARAMETERS: *)
V
max
I
max
C
i
L
i
30 V 90 mA 3 nF 1 µH
Nonincendive field wiring parameters:
THE USB POWER SUPPLY CONTACTS ARE DEPENDENT UPON THE FOLLOWING ENTITY PARAMETERS: *)
V
OC
I
SC
C
a
L
a
5,5 V 1.25A 10 µF 10 µH
FAULT contacts
USB pin 4 USB pin 1
Any EAGLEONE-0200xxx or TOFINOXE-0200xxx device

Installation EAGLE One
Release 03 07/2014 11
SUITABLE FOR USE IN CLASS I DIVISION 2 GROUPS A, B ,C ,D HAZARDOUS LOCATIONS, OR NONHAZARDOUS LOCATIONS ONLY. For use in HARDOUS LOCATIONS only allowed for model No´s. which are labelled accordingly. 
Nonincendive field wiring circuits must be wired in accordance with the National Electrical Code (NEC), NFPA 70 , article 501.
USB AND RELAY CONTACTS (FAULT): Install per Control Drawing 000174247DNR.
WARNING - EXPLOSION HAZARD – SUBSTITUTION OF ANY COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I DIVISION 2. WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.. *) Notes: The nonincendive field wiring circuit concept allows interconnection of nonincendive field wiring apparatus and associated
nonincendive field wiring apparatus using any of the wiring methods permitted for unclassified locations when certain parametric conditions are met. Capacity: C
a
C
i
+ C
Cable
; Inductivity: L
a
L
i
+ L
Cable
The maximum cable length has to be determined as follows: (a) max. Cable Length < (L
a
-L
i
) / Cable
L
(”Cable
L
“ denotes the inductance per unit length of used cable) and
(b) max. Cable Length < (C
a
-C
i
) / Cable
C
(“Cable
C
“ denotes the capacitance per unit length of used cable).
The lower value of (a) and (b) is to apply. Manufactured in 72654 Neckartenzlingen / Germany by Hirschmann Automation and Control GmbH. DOM: ww/yyyy (Date of manufactur w - week, Y - year. Refer to the device label).
CONTROL DRAWING to EAGLEONE and TOFINOXE series for Use in Hazardous Locations Class I Division 2, Groups A, B, C, D Rev. 0 Document No.: 000174247DNR Page 2/2

12 Installation EAGLE One
Release 03 07/2014
Relevant for use in Ex Zone 2 according to ATEX 95
(European directive 94/9/EC)
In Ex Zone 2, only the devices with a corresponding label may be
operated.
The USB contacts are to be installed and used within their Entity
Parameters as per Control Drawing 000174247DNR according to the
European directive 94/9/EC – details see the next two pages.

Installation EAGLE One
Release 03 07/2014 13
CONTROL DRAWING for EAGLEONE and TOFINOXE Series according to the European Directive 94/9/EC Rev. 0 Document No.: 000174247DNR Page 1/2
MSP30 / MSP32
ATEX Zone 2
Explosive Atmosphere
Ordinary Location, Non-Hazardous Area,
Nonexplosive Atmosphere
1 2 3 4 4 3 2 1
The earth conductor must be
at least of the same wire size (mm² or AWG) as the supply conductors.
THE Fault Relays are tested as Sealed Device
according to ATEX EN 60079-15. Switching current max. 1 A, (resistive load) Switching voltage max. 60 VDC or 30 VAC
, SELV
FAULT contacts
USB pin 4 USB pin 1
Any EAGLEONE-0200xxx or TOFINOXE-0200xxx device
Temperature Code: T4
Ambient Temperature rating: Ta : 0°C to +60°C for “S” types Ta: -40°C to +70°C for “T” or “E” types - refer to the type designation on the device (item 18 of product code: “Temperature range”).
Nonincendive field wiring parameters:
THE USB POWER SUPPLY CONTACTS ARE DEPENDENT UPON THE FOLLOWING ENTITY PARAMETERS: WARNING: Exclusively use ACA USB devices
with in
p
ut current less than 0
,
35 A.
U
O
I
O
C
O
L
O
5,5 V 1.25A 10 µF 10 µH

14 Installation EAGLE One
Release 03 07/2014
For Use in explosive atmospheres according to the European directive 94/9/EC:
Applied Standards: EN60079-0, 2012
EN60079-11, 2012 EN60079-15, 2010
The Use in Hazardous Locations with explosive atmospheres is only allowed for EAGLEONE or TOFINOXE model No´s. which are labeled accordingly – including “
8
II 3G” , “Ex nA IIC ic T4 Gc” , “DEKRA 13ATEX0184X”
SPECIAL CONDITIONS FOR SAFE USE: •The modules shall be installed in a suitable enclosure providing a degree of protection of at least IP54 according
to EN60529, taking into account the environmental conditions under which the equipment will be used.
•Provisions shall be made to prevent the rated voltage from being exceeded by transient disturbances of more
than 119V.
•When the temperature under rated conditions exceeds 70°C at the cable or conduit entry point, or 80°C at the
branching point of the conductors, the temperature specification of the selected cable shall be in compliance with the actual measured temperature values.
Manufactured in 72654 Neckartenzlingen / Germany by Hirschmann Automation and Control GmbH. DOM: ww/yyyy (Date of manufactur w - week, Y - year. Refer to the device label).
CONTROL DRAWING to EAGLEONE and TOFINOXE series according to the European Directive 94/9/EC Rev. 0 Document No.: 000174247DNR Page 2/2

Installation EAGLE One
Release 03 07/2014 15
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

16 Installation EAGLE One
Release 03 07/2014
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the CD/DVD supplied:
Installation user manual
Configuration user manual
Command Line Interface user manual
Reference manual for the graphical user interface
The Industrial HiVision network management software provides you with
additional options for smooth configuration and monitoring:
ActiveX control for SCADA integration
Auto-topology discovery
Browser interface
Client/server structure
Event handling
Event log
Simultaneous configuration of multiple devices
Graphical user interface with network layout
SNMP/OPC gateway
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

Installation EAGLE One
Release 03 07/2014 17
1 Description
1.1 General description
The EAGLE One devices support the authentication, security and
confidentiality of communication within production networks, but also beyond
company boundaries.
The EAGLE One devices support the following network modes:
Transparent mode
Router mode
PPPoE mode
The EAGLE One devices are used everywhere that security-sensitive
network cells require a connection from the internal network to the external
network. The EAGLE One devices are the link between the internal network
and the external network from which unauthorized access is possible. In its
function as a link, the EAGLE One devices help you to protect the security-
sensitive cell from undesired data traffic along the connection to the external
network.
Typical uses are:
Helping protect individual production cells in a flat company network
Helping protect individual production cells in a routed company network
Coupling identical production cells to a company network
Connecting a production cell with the office network via a public network
Helping provide protected service access
Separation of machine common parts
You can choose from between a wide range of variants. You have the option
to set up your device individually based on different criteria:
Types of connectors
Temperature range
Certifications
The EAGLE One devices are designed for the special requirements of
industrial automation. They meet the relevant industry standards, provide
very high operational reliability, even under extreme conditions, and also
long-term reliability and flexibility.
The devices allow you to set up switched and routed industrial Ethernet
networks that conform to the IEEE 802.3 standard.

18 Installation EAGLE One
Release 03 07/2014
The following installation options are available:
simply snapping them onto a DIN rail
Mounting on a vertical flat surface
The devices work without a fan.
There are convenient options for managing the device. Administer your
devices via:
Network management software (e.g. Industrial HiVision)
a Web browser
a V.24 interface (locally on the device)
HiDiscovery (Software for putting the device into operation)
SSH
The devices provide you with a large range of functions, which the manuals
for the operating software inform you about. You will find these manuals as
PDF files on the enclosed CD/DVD, or you can download them from the
Internet on the Hirschmann product pages (www.hirschmann.com).
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.
Item Product characteristic Characteris
tic value
Description
1 ... 8 Device EAGLEONE 2 port Eagle router
9–
10 ... 11 Number:
Fast Ethernet ports
02 2 × Fast Ethernet ports
12 ... 13 Number:
Gigabit Ethernet ports
00 0 × Gigabit Ethernet ports
14 ... 15 Ethernet port 1
INTERNAL
T1 1 × RJ45 socket for 10/100 Mbit/s twisted
pair connections
M2 1 × DSC multimode socket for 100 Mbit/s
F/O port
16 ... 17 Ethernet port 2
EXTERNAL
T1 1 × RJ45 socket for 10/100 Mbit/s twisted
pair connections
M2 1 × DSC multimode socket for 100 Mbit/s
F/O port
Table 1: Device name and product code

Installation EAGLE One
Release 03 07/2014 19
18 Temperature range E Extended with
conformal coating
−40 °F ... +158 °F
(−40 °C ... +70 °C)
S Standard +32 °F ... +140 °F
(0 °C ... +60 °C)
T Extended −40 °F ... +158 °F
(−40 °C ... +70 °C)
19 ... 20 Working voltage DD 2 voltage inputs for redundant power
supply
Rated voltage range DC
12 V ... 48 V
Nominal voltage AC
24 V
21 ... 22 Certificates and
declarations
Note: You will find detailed information on the certificates
and declarations applying to your device in a separate
overview.
See table 3 on page 21.
23 ... 26 Software packages 0000 Basic Software-Packages
27 ... 28 Customer-specific
version
HH Hirschmann standard
29 Software configuration E Entry (Hirschmann standard configuration)
30 ... 34 Software version 05.3 Software version 05.3
XX.X Current software version
35 ... 36 Bug fix 00 Bugfix version 00
XX Current bugfix version
Item Product characteristic Characteris
tic value
Description
Table 1: Device name and product code

20 Installation EAGLE One
Release 03 07/2014
Item Product characteristic Description
EAGLEONE
1 ... 8 Device 2 port Eagle router
–
9–
02
10 ... 11 Number:
Fast Ethernet ports
2 × Fast Ethernet ports
00
12 ... 13 Number:
Gigabit Ethernet ports
0 × Gigabit Ethernet ports
T1
14 ... 15 Ethernet port 1
INTERNAL
1 × RJ45 socket for 10/100 Mbit/s twisted pair
connections
T1
16 ... 17 Ethernet port 2
EXTERNAL
1 × RJ45 socket for 10/100 Mbit/s twisted pair
connections
E
18 Temperature range Extended with conformal
coating
−40 °F ... +158 °F
(−40 °C ... +70 °C)
DD
19 ... 20 Working voltage 2 voltage inputs for redundant power supply
Rated voltage range DC
12 V ... 48 V
Nominal voltage AC
24 V
Z9
21 ... 22 Certificates and
declarations
Standard applications
CE
EN 60950-1
EN 61131-2
FCC
0000
23 ... 26 Software packages Basic Software-Packages
HH
27 ... 28 Customer-specific
version
Hirschmann standard
E
29 Software configuration Entry (Hirschmann standard configuration)
XX.X
30 ... 34 Software version Current software version
XX
35 ... 36 Bug fix Current bugfix version
Table 2: Sample product code (left column):