Hirschmann MSP30 User manual

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
MICE Switch Power - MSP30/32/40/42
MICE Switch Media modules - MSM20/22/24/40/42/46/50

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2018 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50 07.06.18

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 3
Contents
Safety instructions 6
About this manual 17
Key 18
1 Description 19
1.1 General device description 19
1.1.1 Basic device 19
1.1.2 Media modules 19
1.2 Device name and product code 20
1.3 Device views 26
1.3.1 Basic device 26
1.3.2 Media modules 30
1.4 Number of ports and connections 37
1.5 Power supply 39
1.5.1 Supply voltage with the characteristic value C 39
1.5.2 Supply voltage with the characteristic value P 39
1.6 SFP Transceiver 39
1.7 Ethernet ports 39
1.8 Display elements 42
1.8.1 Device state 42
1.8.2 Digital input 43
1.8.3 MSM20 media modules 43
1.8.4 MSM40 media modules 44
1.8.5 MSM22, MSM42 and MSM46 media modules 45
1.8.6 MSM50 media modules 46
1.8.7 MSM24 I/O module 46
1.9 Management interfaces 48
1.9.1 V.24 interface (external management) 48
1.9.2 SD card interface (optional) 48
1.9.3 USB interface 49
1.10 Input/output interfaces 49
1.10.1 Signal contact 49
1.10.2 Digital input 50
2 Installation 51
2.1 Checking the package contents 51
2.2 Installing the SD card (optional) 51

4Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
2.3 Installing and grounding the device 52
2.3.1 Installing the device onto the DIN rail 52
2.3.2 Mounting on a flat surface 53
2.3.3 Grounding the device 53
2.4 Connecting the terminal blocks 54
2.4.1 Supply voltage with the characteristic value C 54
2.4.2 Supply voltage with the characteristic value P 55
2.4.3 Signal contact 56
2.5 Connecting the ferrite 56
2.6 Installing terminal blocks, switching on the supply voltage 57
2.7 Installing media modules 57
2.7.1 Device variants featuring customer-specific version
with the characteristic value HH 58
2.7.2 Device variants featuring customer-specific version
with the characteristic value HX 59
2.7.3 Connecting the external PoE supply voltage of media
module MSM46 59
2.8 Connecting an I/O module 60
2.8.1 Connecting actuators and sensors 60
2.9 Installing an SFP transceiver (optional) 61
2.10 Connecting data cables 62
2.10.1 10/100/1000 Mbit/s twisted pair port 63
2.10.2 10/100 Mbit/s twisted pair port 63
2.10.3 1/2.5 Gbit/s F/O port 63
2.10.4 100/1000 Mbit/s F/O port 63
2.10.5 100 Mbit/s F/O port 63
3 Basic Settings 64
4 Monitoring the ambient air temperature 65
5 Upgrading Software 66
6 Maintenance and service 67
7Disassembly 68
7.1 Removing an SFP transceiver (optional) 68
7.2 Removing a media module 68
7.2.1 Device variants featuring customer-specific version
with the characteristic value HH 69
7.2.2 Device variants featuring customer-specific version
with the characteristic value HX 70

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 5
7.3 Removing the device 70
7.3.1 Device variants featuring customer-specific version
with the characteristic value HH 71
7.3.2 Device variants featuring customer-specific version
with the characteristic value HX 71
8 Technical data 72
8.1 General technical data 72
8.2 Digital input 75
8.3 Digital output 75
8.4 24 V DC auxiliary voltage (AUX) 76
8.5 External PoE power supply (MSM46) 76
8.6 Dimension drawings 77
8.7 EMC and immunity 82
8.8 Power consumption/power output 85
8.9 Network range 86
9 Scope of delivery, order numbers and
accessories 89
9.1 Scope of delivery 89
9.2 Accessories 89
10 Underlying technical standards 92
A Further support 93

6Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning the device, turn off the supply voltage and return the
device to Hirschmann for inspection.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 72.
Connect to the product only components suitable for the requirements
of the specific application case.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 7
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Installation site requirements
Verify that there is at least 4 in (10 cm) of space above and below the
device.
Verify that there is at least 0.8 in (2 cm) of space on the right and left
sides of the device.
Install the device at ambient temperatures greater than 113 °F (45 °C)
in “restricted access locations” based on EN 60950-1 exclusively.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Make sure there is at least 3.94 in (10 cm) of space in front of the
ventilation slits of the casing.
Keep the ventilation slits free to ensure good air circulation.
If you are operating the device in a living area or office environment,
only operate it in switch cabinets with fire protection characteristics in
accordance with EN 60950-1.
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
Note: The basic device is an inseparable unit. The basic device may be
damaged by detachment of the display and connection part.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected shielded twisted pair cable is connected
to the grounding connector on the front panel as a conductor.

8Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the
requirements listed are complied with.
General requirements for connecting electrical wires
The following requirements apply without restrictions:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
Relevant for North America:
Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.
Requirements for connecting the signal contact
The following requirements apply without restrictions:
The voltage connected complies with the requirements for a safety extra-low voltage
(SELV) as per IEC/EN 60950-1.
The connected voltage is limited by a current limitation device or a fuse.
Observe the electrical threshold values for the signal contact.
See “General technical data” on page 72.
Requirements for connecting the supply voltage
The following requirements apply without restrictions:
All of the following requirements are complied with:
The supply voltage corresponds to the voltage specified on the type plate of the device.
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device (for example a switch or
a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is
clear which disconnecting device belongs to which power supply cable.
The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on
the supply voltage input.
The following requirements apply alternatively:
Relevant when the device is supplied via 1 voltage input:
Alternative 1 The power supply complies with the requirements for a limited power source
(LPS) as per EN 60950-1.
Alternative 2 Relevant for North America:
The power supply complies with the requirements according to NEC Class 2.
Alternative 3 All of the following requirements are complied with:
The power supply complies with the requirements for a safety extra-low
voltage (SELV) as per IEC/EN 60950-1.
A fuse suitable for DC voltage is located in the plus conductor of the power
supply.
The minus conductor is on ground potential. Otherwise, a fuse is also
located in the minus conductor.
Regarding the properties of this fuse:
See “Technical data” on page 72.
Relevant when the device is supplied via 2 voltage inputs:
Alternative 1 The total voltage supply meets the requirements for a limited power source
(LPS) as per EN 60950-1.
Alternative 2 Relevant for North America:
The total voltage supply complies with the requirements as per NEC Class 2.

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 9
ESD Guidelines
The modules are equipped with electrostatically sensitive components.
These can be destroyed, or their life cycles reduced, by the effects of an
electrical field or by a charge equalization if the connections are touched.
You will find information about electrostatically endangered assemblies in
DIN EN 61340-5-1 (2007-08) and DIN EN 61340-5-2 (2007-08).
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2014/30/EU (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
www.hirschmann.com
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55032
Reliability: EN 60950-1
You find more information on technical standards here:
See “Technical data” on page 72.
Alternative 3 All of the following requirements are complied with:
The power supply complies with the requirements for a safety extra-low
voltage (SELV) as per IEC/EN 60950-1.
A fuse suitable for DC voltage is located at both voltage inputs in the plus
conductor of the power supply.
The minus conductor is on ground potential at both voltage inputs.
Otherwise, a fuse is also located in the minus conductor.
Regarding the properties of this fuse:
See “Technical data” on page 72.
Requirements for connecting the supply voltage

10 Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
LED or laser components
LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
LED CLASS 1 - CLASS 1 LED PRODUCT, relevant for the following F/O
modules (indicated by the module code): M2, M4.
LASER CLASS 1 - CLASS 1 LASER PRODUCT, relevant for the
following F/O modules (indicated by the module code): S2, S4, G2, L2,
C1.
For a description of the nomenclature for module codes, see table 2 on
page 22.
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.
The following approvals are only in place for the media modules
MSM20/24/40/42 in connection with a MSP30/32/40/42 basic device:

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 11
Relevant for use as industrial switching equipment
(according to standards UL 508 /
CSA C22.2 No. 142-1987)
When using the MSP30/32/40/42 devices as industrial control equipment
the following restrictions apply:
Max. ambient air temperature: +140 °F (+60 °C)
(... applies to operating temperature characteristic values S, T or E)
Exclusively use copper conductors.
Temperature rating of field installed conductors: Exclusively use +167° F
(+75 °C) conductors.
Exclusively use +167 °F (+75 °C) copper conductors.
Exclusively for use in Pollution degree 2 environment.
Digital output:
Basic devices MSP30/32/40/42 - Relay (Fault): max. 30 V DC, 1 A,
resistive load.
Media module MSM24 - (O1, ..., O4): max. 30 V DC, 1 A, resistive load.
Relevant for use in explosion hazard areas (Hazardous
Locations, Class I, Division 2)
When using the MSP30/32/40/42 devices as industrial control equipment
the following restrictions apply:
This equipment is suitable for use in Class I, Division 2, Groups A, B ,C,
D – OR non-hazardous locations, if labeled “FOR USE IN HAZARDOUS
LOCATIONS”.
Additional to the restrictions regarding UL 508, the following restrictions
apply:
Ta: –40 °F ... +140°F (–40 °C ... +60 °C), temperature code: T4
for temperature range characteristic values T and E
Ta: +32 °F ... +140 °F (0 °C ... +60 °C), temperature code: T4
for temparature range characteristic value S.
WARNING – EXPLOSION HAZARD – Do not disconnect equipment
unless power has been removed or the area is known to be non-
hazardous.
WARNING – EXPLOSION HAZARD – Substitution of any components
may impair suitability for Class I, Division 2.
– Apply Control Drawing No. 000172287DNR for installation and use
of the MSP basic devices. You find further information on the
following pages.
– Apply Control Drawing No. 000172850DNR for installation and use
of the MSM24 I/O modules. You find further information on the
following pages.

12 Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
– Secure the SD card with the thumb screw. Do not connect or
disconnect the SD card unless the area is known to be non-
hazardous. Connection or disconnection in an explosive atmosphere
could result in an explosion.
Notice: For information about the position on the device see “View
from above” on page 29.
Avertissement - Risque d'explosion - Ne pas débrancher tant que le
circuit est sous tension à moins que l'emplacement soit connu pour ne
contenir aucune concentration de gaz inflammable.
Avertissement - Risque d'explosion - La substitution de tout composant
peut rendre ce matériel incompatible pour une utilisation en classe I,
division 2.

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 13
1RQLQFHQGLYH¿HOGZLULQJSDUDPHWHUV
7+(5(/$<7(50,1$/ $5('(
3(1'(1783217+()2//2:,1*
(17,7<3$5$0(7(5 
8L,L&L/L
9 P$ Q) +
2UGLQDU\/RFDWLRQ1RQ+D]DUGR V
$UHD1RQH[SORVLYH$WPRVSKHUH
&21752/'5$:,1*IRU0 3GHYLFHVIRUXVHLQ+D]DUGRXV
/RFDWLRQV&ODVV,'LYLVLRQ*URXSV$%&'
9HUVLRQ 'RFXPHQWQR'15 3DJH
+D]DUGR V/RFDWLRQ&ODVV,
'LYLVLRQ*UR SV$%&'
7KHHDUWKFRQGXFWRUPXVWEHDWOHDVW
RIWKHVDPHZLUHVL]HPPðRU$:*
DVWKHVXSSO\FRQGXFWRUV
)RU VHLQ+D]DUGR V/RFDWLRQV&ODVV,'LYLVLRQ*UR SV$%&'
2QO\DOORZHGIRU063PRGHOQ PEHUVZKLFKDUHLQGLYLG DOO\ODEHOOHG
³)2586(,1+$5'286/2&$7,216´
 1RQLQFHQGLYH¿HOGZLULQJFLUF LWVP VWEHZLUHGLQDFFRUGDQFHZLWKWKH
 1DWLRQDO(OHFWULFDO&RGH1(&1)3$DUWLFOH
:$51,1*(;3/26,21+$=$5'±68%67,787,212)$1<&20321(1760$<,03$,5
68,7$%,/,7<)25+$=$5'286/2&$7,21625(;3/26,9($70263+(5(6
:$51,1*(;3/26,21+$=$5''2127',6&211(&7(48,30(1781/(6632:(5
+$6%((16:,7&+('2))257+($5($,6.12:172%(121+$=$5'286
1RWHV
7KHQRQLQFHQGLYH¿HOGZLULQJFLUFXLWFRQFHSWDOORZVLQWHUFRQQHFWLRQRIQRQLQFHQGLYH¿HOGZLULQJ
DSSDUDWXVDQGDVVRFLDWHGQRQLQFHQGLYH¿HOGZLULQJDSSDUDWXVXVLQJDQ\RIWKHZLULQJPHWKRGV
SHUPLWWHGIRUXQFODVVL¿HGORFDWLRQVZKHQFHUWDLQSDUDPHWULFFRQGLWLRQVDUHPHW
&DSDFLW\&D&L&&DEOH,QG FWLYLW\/D/L/&DEOH
7KHPD[LPXPFDEOHOHQJWKKDVWREHGHWHUPLQHGDVIROORZV
DPD[&DEOHOHQJWK/D/L&DEOH/
³&DEOH/´GHQRWHVWKHLQGXFWDQFHSHUXQLWOHQJWKRIXVHGFDEOHDQG
EPD[&DEOHOHQJWK&D&L&DEOH&
³&DEOH&´GHQRWHVWKHFDSDFLWDQFHSHUXQLWOHQJWKRIXVHGFDEOH
7KHORZHUYDO HRIDDQGELVWRDSSO\
0DQXIDFWXUHG LQ'1HFNDUWHQ]OLQJHQ*HUPDQ\E\+LUVFKPDQQ$XWRPDWLRQDQG&RQWURO
*PE+'20ZZ\\\\'DWHRIPDQXIDFWXUHZZHHN\\HDU5HIHUWRWKHGHYLFHODEHO
063
063
063
063
7KH8 %FRQQHFWRUDQGWKH9
FRQQHFWRU5-DUHIRUWHPSRUDU\
FRQQHFWLRQRQO\'RQRWXVHFRQQHFW
RUGLVFRQQHFWXQOHVVDUHDLVNQRZQ
WREHQRQKD]DUGRXV&RQQHFWLRQRU
GLVFRQQHFWLRQLQDQH[SORVLYHDWPR
VSKHUHFRXOGUHVXOWLQDQH[SORVLRQ

14 Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
CONTROL DRAWING for MSM24-IOIOIOIO devices
for Use in Hazardous Locations Class I Division 2 , Groups A, B, C, D Rev. 0 Document No.:000172850DNR Page 1/2
Nonincendive field wiring parameters:
THE RELAY TERMINALS ARE DEPENDENT UPON THE FOLLOWING ENTY PARAMETERS: *)
U
i
I
i
C
i
L
i
30 V 90 mA 5 nF 1 µH
The Entity Parameters are to apply to the following pin combinations: pin 2 and pin 1; pin 2 and pin 3, pin 5 and pin 4; pin 5 and pin 6, pin 8 and pin 7; pin 8 and pin 9, pin 11 and pin10; pin 11 and pin 12.
Detail of MSM24-IOIOIOIO
Class I Division 2, Groups A, B, C, D
Hazardous Location
Ordinary Location, Non-Hazardous Area,
Nonexplosive Atmosphere
Pin

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 15
For Use in Hazardous Locations Class I Division 2 Groups A, B ,C ,D: Only allowed for MSP30 or MS32 model No´s. which are individually labelled ´)2586(,1+$=$5'286/2&$7,216µ
Nonincendive field wiring circuits must be wired in accordance with the National Electrical Code (NEC), NFPA 70 , article 501.
WARNING - EXPLOSION HAZARD – SUBSTITUTION OF ANY COMPONENTS MAY IMPAIR SUITABILITY FOR HAZARDOUS LOCATIONS OR EXPLOSIVE ATMOSPHERES. WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS. *) Notes: The nonincendive field wiring circuit concept allows interconnection of nonincendive field wiring apparatus and
associated nonincendive field wiring apparatus using any of the wiring methods permitted for unclassified locations when certain parametric conditions are met. Capacity: C
a
C
i
+ C
Cable
; Inductivity: L
a
L
i
+ L
Cable

   The maximum cable length has to be determined as follows: (a) max. Cable Length < max. Cable Length < (L
a
-L
i
) / Cable
L
(”Cable
L
“ denotes the inductance per unit length of used cable) and
(b) max. Cable Length < max. Cable Length < (C
a
-C
i
) / Cable
C
(“Cable
C
“ denotes the capacitance per unit length of used cable).
The lower value of (a) and (b) is to apply. Manufactured in 72654 Neckartenzlingen / Germany by Hirschmann Automation and Control GmbH. DOM: ww/yyyy (Date of manufactur w - week, Y - year. Refer to the device label).
CONTROL DRAWING for MSM24-IOIOIOIO devices
for Use in Hazardous Locations Class I Division 2 , Groups A, B, C, D Rev. 0 Document No.: 000172850DNR Page 2/2

16 Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
ATEX directive 2014/34/EU – specific regulations for safe
operation
In Ex zone 2, only devices with a corresponding label may be operated.
When operating the devices and modules in Ex zone 2, the following
applies:
II 3G
Ex nA IIC T4 Gc
Ta: –40 °C ... +70 °C for characteristic values T and E for
temperature range
Ta: 0 °C ... +60 °C for characteristic value S for temperature
range
DEKRA 13ATEX0090 X
DO NOT OPEN THE DEVICE WHEN IT IS ELECTRICALLY CHARGED.
THE USB CONNECTOR MUST NOT BE USED WHEN THE DEVICE IS
OPERATED IN EXPLOSIVE HAZARDOUS LOCATIONS.
Special conditions for safe use
The basic devices and media modules shall be installed in a suitable
enclosure providing a degree of protection of at least IP54 according
to EN 60079-15, taking into account the ambient conditions under
which the equipment will be used.
When the temperature under rated conditions exceeds 158 °F (70 °C)
on the cable or at conduit entry point, or 176 °F (80 °C) at the
branching point of the conductors, take measures so that the
temperature specification of the selected cable is in compliance with
the actual measured temperature values.
Provisions shall be made to prevent the rated voltage from being
exceeded by transient disturbances of more than 119 V.
If an SD card is used, it has to be secured with a knurled screw. For
information about the position on the device see “View from above” on
page 29.
Temperature code T4
List of
standards:
EN 60079-0: 2012
EN 60079-15: 2010

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 17
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the Internet on the
Hirschmann product pages (www.hirschmann.com):
User Manual Installation
Basic Configuration user manual
Redundancy Configuration user manual
Reference manual for the graphical user interface
Command Line Interface reference manual

18 Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018 19
1 Description
1.1 General device description
The MSP30/32/40/42 and MSM20/22/24/40/42/46/50 devices are designed
for the special requirements of industrial automation. They meet the relevant
industry standards, provide very high operational reliability, even under
extreme conditions, and also long-term reliability and flexibility.
The devices allow you to set up switched industrial Ethernet networks that
conform to the IEEE 802.3 standard.
The devices work without a fan.
You have the option of choosing various media to connect to the end devices
and other network components:
multimode F/O
singlemode F/O
twisted pair cable
The devices provide you with a large range of functions, which the manuals
for the operating software inform you about. You find these manuals in the
form of PDF files for downloading on the Internet on the Hirschmann product
pages (www.hirschmann.com).
The Hirschmann network components help you ensure continuous
communication across all levels of the company.
The Industrial HiVision Network Management software provides you with
additional options for smooth configuration and monitoring: You find further
information on the Internet at the Hirschmann product pages:
www.hirschmann.com/en/Hirschmann_Produkte/Industrial_Ethernet/
network-management-software/index.phtml
1.1.1 Basic device
There are convenient options for managing the device. Manage your devices
via:
network management software (for example Industrial HiVision)
Web browser
V.24 interface (locally on the device)
HiDiscovery (software for putting the device into operation)
SSH
Telnet
1.1.2 Media modules
The media modules form the interface from the device to the LAN.

20 Installation MSP30/32/40/42 and MSM20/22/24/40/42/46/50
Release 12 06/2018
The media modules have different interface types.
The different interfaces of the media modules provide you with the following
functions:
Specific functions of the TP/TX interface
Auto Polarity Exchange
Autocrossing (device may be connected with a crossed-over or an un-
crossed cable)
Autonegotiation (selecting the operating mode: speed/duplex)
Link Control
Specific functions of the F/O interface
Link Down monitoring
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.
You have numerous options of combining the device characteristics. You can
determine the possible combinations using the Configurator which is
available in the Belden E-Catalog (www.e-catalog.beldensolutions.com) on
the web page of the device.
Basic device
Item Characteristic Characteri
stic value
Description
1 ... 3 Product MSP MICE Switch Power
4Datarate 3 10
a/100 Mbit/s ports
10 a/100/1000 Mbit/s ports
410
a/100/1000 Mbit/s ports
1000/2500 Mbit/s ports
5 Hardware type 0 Standard
2 Suitable for PoE or PoE+
6 (hyphen) -
7 ... 8 Number:
10 a/100 Mbit/s ports
00 0 ×
08 8 ×
16 16 ×
24 24 ×
9 ... 10 Number:
10 a/100/1000 Mbit/s
ports
04 4 ×
12 8 × + 4 × 1000/2500 Mbit/s ports
20 16 × + 4 × 1000/2500 Mbit/s ports
28 24 × + 4 × 1000/2500 Mbit/s ports
Table 1: Device name and product code