Hirschmann RS20 series User manual

RM Web L2E
Release 5.0 04/09
Technical Support
[email protected]
Reference Manual
Web-based Interface
Industrial ETHERNET (Gigabit) Switch
RS20/RS30/RS40, MS20/MS30, OCTOPUS

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2009 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the en-
closed CD applies.
The performance features described here are binding only if they have been expressly guaran-
teed in the contract. This publication has been created by Hirschmann Automation and Control
GmbH according to the best of our knowledge. Hirschmann reserves the right to change the con-
tents of this manual without prior notice. Hirschmann gives no guarantee in respect of the cor-
rectness or accuracy of the details in this publication.
Hirschmann accepts no responsibility for any damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can find the current version of this manual on the Internet, on the Hirschmann product pages
(www.hirschmann-ac.de).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Rel. 5.0-01-0708 – 29.4.09

Content
RM Web L2E
Release 5.0 04/09 3
Content
Content 3
About this Manual 7
Key 9
Opening the Web-based Interface 11
1 Basic Settings 15
1.1 System 16
1.2 Network 21
1.3 Software 23
1.3.1 View the software versions present on the device 23
1.3.2 Update via file selection 24
1.3.3 tftp update 24
1.4 Port configuration 25
1.5 Power over ETHERNET 27
1.6 Load/Save 29
1.6.1 Loading the configuration 30
1.6.2 Saving the configuration 30
1.6.3 URL 31
1.6.4 Deleting a configuration 31
1.6.5 Using the AutoConfiguration Adapter (ACA) 32
1.6.6 Canceling a configuration change 33
1.7 Restart 35
2 Security 37
2.1 Password / SNMP Access 38
2.2 SNMPv1/v2 Access Settings 40
2.3 Telnet/Web Access 43
2.3.1 Description of Telnet access 43
2.3.2 Description of Web access 44
2.4 Port Security 45

Content
4RM Web L2E
Release 5.0 04/09
3Time 49
3.1 SNTP configuration 51
3.2 PTP (IEEE 1588) 54
3.2.1 PTP Global (MS20/MS30, PowerMICE) 55
3.2.2 PTP Version 1 (MS20/MS30, Power MICE) 57
3.2.3 PTP Version 2 (BC) (MS20/MS30, PowerMICE) 60
3.2.4 PTP Version 2 (TC) (MS20/MS30, PowerMICE) 65
4 Switching 69
4.1 Switching Global 70
4.2 Filters for MAC addresses 71
4.3 Rate Limiter 73
4.3.1 Rate Limiter settings 73
4.4 Multicasts 75
4.4.1 Global Configuration 75
4.4.2 IGMP Querier and IGMP settings 76
4.4.3 Unknown Multicasts 78
4.4.4 Known Multicasts 79
4.4.5 Settings per port (table) 80
4.5 VLAN 83
4.5.1 VLAN Global 83
4.5.2 Current VLAN 86
4.5.3 VLAN Static 88
4.5.4 VLAN Port 90
5 QoS/Priority 93
5.1 Global 94
5.2 Port configuration 97
5.2.1 Entering the port priority 98
5.3 802.1D/p Mapping 99
5.4 IP DSCP mapping 101

Content
RM Web L2E
Release 5.0 04/09 5
6 Redundancy 103
6.1 Ring Redundancy 104
6.1.1 Configuring the HIPER-Ring 106
6.1.2 Configuring the MRP-Ring 109
6.2 Ring/Network coupling 112
6.2.1 Preparing a Ring/Network coupling 112
6.3 Rapid Spanning Tree 119
6.3.1 Rapid Spanning Tree Global 121
6.3.2 Rapid Spanning Tree Port 125
7 Diagnosis 129
7.1 Event log 130
7.2 Ports 131
7.2.1 Statistics table 131
7.2.2 Utilization 132
7.2.3 SFP modules 133
7.3 Topology Discovery 134
7.4 Port Mirroring 136
7.5 Device Status 138
7.6 Signal contact 140
7.6.1 Manual setting 140
7.6.2 Function monitoring 140
7.6.3 Device status 142
7.6.4 Configuring traps 142
7.7 Alarms (Traps) 143
7.8 Report 145
7.9 IP address conflict detection 146
7.10 Self Test 148
7.11 Service mode 149
7.11.1Activating the service mode 149
7.11.2Deactivating the service mode 151

Content
6RM Web L2E
Release 5.0 04/09
8 Advanced 153
8.1 DHCP Relay Agent 154
8.2 Industrial Protocols 156
8.2.1 PROFINET IO 157
8.2.2 EtherNet/IP 157
8.3 Command Line 158
A Appendix 159
A.1 Technical Data 160
A.2 List of RFCs 161
A.3 Based specifications and standards 163
A.4 Copyright of integrated software 164
A.4.1 Bouncy Castle Crypto APIs (Java) 164
A.4.2 LVL7 Systems, Inc. 165
B Readers’ comments 167
C Index 169
D Further support 171

About this Manual
RM Web L3P+
Release 5.0 04/09 7
About this Manual
The "Web-based Interface" reference manual contains detailed information
on using the Web interface to operate the individual functions of the device.
The "Command Line Interface" reference manual contains detailed informa-
tion on using the Command Line Interface to operate the individual functions
of the device.
The “Installation” user manual contains a device description, safety instruc-
tions, a description of the display, and all the other information that you need
to install the device before you begin with the configuration of the device.
The “Basic Configuration” user manual contains all the information you need
to start operating the device. It takes you step by step from the first startup
operation through to the basic settings for operation in your environment.
The “Redundancy Configuration” user manual contains all the information
you need to select a suitable redundancy procedure and configure it.
The “Industry Protocols” user manual describes how the device is connected
by means of a communication protocol commonly used in the industry, such
as EtherNet/IP and PROFINET.
The Network Management Software HiVision/Industrial HiVision provides
you with additional options for smooth configuration and monitoring:
XConfiguration of multiple devices simultaneously.
XGraphical interface with network layouts.
XAuto-topology discovery.
XEvent log.
XEvent handling.
XClient / Server structure.
XBrowser interface
XActiveX control for SCADA integration
XSNMP/OPC gateway

About this Manual
8RM Web L3P+
Release 5.0 04/09

Key
RM Web L3P+
Release 5.0 04/09 9
Key
The designations used in this manual have the following meanings:
Symbols used:
XList
Work step
Subheading
Link Indicates a cross-reference with a stored link
Note: A note emphasizes an important fact or draws your
attention to a dependency.
Courier ASCII representation in user interface
Router with firewall
Switch with firewall
Router
Switch
Bridge
Hub

Key
10 RM Web L3P+
Release 5.0 04/09
A random computer
Configuration Computer
Server
PLC -
Programmable logic
controller
I/O -
Robot

Opening the Web-based Interface
RM Web L3P+
Release 5.0 04/09 11
Opening the Web-based Interface
To open the Web-based interface, you will need a Web browser (a program
that can read hypertext), for example Mozilla Firefox version 1 or later, or Mi-
crosoft Internet Explorer version 6 or later.
Note: The Web-based interface uses the Java software version 5 or later (Ja-
va™ Runtime Environment Version 1.5.x or 6.x). If it is not installed on your
computer yet, it will be installed automatically via the Internet when you start
the Web-based interface for the first time.
For Windows users: If you don´t have any access to the internet cancel the
installation. Install the software from the enclosed CD-ROM. To do this, you
go to “Additional Software”, select Java Runtime Environment and click
on “Installation”.
Figure 1: Installing Java
Start your Web browser.
Make sure that you have activated JavaScript and Java in the security
settings of your browser.

Opening the Web-based Interface
12 RM Web L3P+
Release 5.0 04/09
Establish the connection by entering the IP address of the device which
you want to administer via the Web-based management in the address
field of the Web browser. Enter the address in the following form:
http://xxx.xxx.xxx.xxx
The login window appears on the screen.
Figure 2: Login window
Select the desired language.
In the drop-down menu, you select
– user, to have read access, or
– admin, to have read and write access
to the device.
The password “public”, with which you have read access, appears in the
password field. If you wish to have write access to the device, then high-
light the contents of the password field and overwrite it with the password
“private” (default setting).
Click on OK.
The Web site of the device appears on the screen.

Opening the Web-based Interface
RM Web L3P+
Release 5.0 04/09 13
Note: The changes you make in the dialogs are copied to the device when
you click on “Set”. Click on “Load” to update the display.
Note: You can block your access to the device by entering an incorrect con-
figuration.
Activating the function “Cancel configuration change” in the “Load/Save”
dialog enables you to return automatically to the last configuration after a set
time period has elapsed. This gives you back your access to the device.
Figure 3: Website of the device with speech-bubble help

Opening the Web-based Interface
14 RM Web L3P+
Release 5.0 04/09
The menu section displays the menu items. By placing the mouse pointer in
the menu section and clicking the right mouse button you can use “Back” to
return to a menu item you have already selected, or “Forward” to jump to a
menu item you have already selected.

Basic Settings
RM Web L3P+
Release 5.0 04/09 15
1 Basic Settings
The basic settings menu contains the dialogs, displays and tables for basic
settings configuration:
XSystem
XNetwork
XSoftware
XPort configuration
XPower over Ethernet
XLoad/Save
XRestart

Basic Settings
16
1.1 System
RM Web L3P+
Release 5.0 04/09
1.1 System
The „System“ submenu in the basic settings menu is structured as follows:
XDevice status
XSystem data
XDevice view
XReloading data
Figure 4: "System" submenu
Device status
This section of the website provides information on the device status and
the alarm state of the device.

Basic Settings
RM Web L3P+
Release 5.0 04/09
1.1 System
17
Figure 5: Device status and alarm display
1 - Symbol indicates the Device Status
2 - Cause of the oldest existing alarm
3 - Time of the oldest existing alarm
System data
This area of the website displays the system parameters of the device.
Here you can change,
– the system name,
– the location description,
– the name of the contact person for this device,
– the availability of the media modules (see fig. 6) and
– the temperature threshold values.
Name Meaning
Name System name of this device
Location Location of this device
Contact person Contact person for this device
Basic module Hardware version of the basic module
Media module 1 Hardware version of media module 1
Media module 2 Hardware version of media module 2
Media module 3 Hardware version of media module 3
Media module 4 Hardware version of media module 4
Media module 5 Hardware version of media module5
Media module 6 Hardware version of media module 6
Media module 7 Hardware version of media module 7
Power supply (P1/P2) Status of the power supply units
Operating time Time that has elapsed since the device was last restarted.
Temperature Temperature in the device. Lower/upper temperature thresh-
old values. If the temperature goes outside this range, the
device generates an alarm message.
Table 1: System data
132

Basic Settings
18
1.1 System
RM Web L3P+
Release 5.0 04/09
Figure 6: Availability of the media modules
1 - Module present
2 - Empty slot
3 - Module was removed. Click this check mark to define this slot as an
empty slot.
Device view
The device view shows the device with the current configuration. The
symbols underneath the device view represent the status of the individual
ports.
123

Basic Settings
RM Web L3P+
Release 5.0 04/09
1.1 System
19
Figure 7: Device view
Meaning of the symbols:
The port (10, 100 Mbit/s, 1, 10 Gbit/s) is enabled
and the connection is OK.
The port is disabled by the management
and it has a connection.
The port is disabled by the management
and it has no connection.
The port is in autonegotiation mode.
The port is in HDX mode.
The port is in RSTP discarding mode (100 Mbit/s).
The port is in routing mode (100 Mbit/s).
Updating
This area of the website at the bottom left displays the countdown time
until the applet requests the current data of this dialog again. Clicking the
"Update" button calls the current dialog information immediately.
The applet polls the current data of the device automatically every 100
seconds.

Basic Settings
20
1.1 System
RM Web L3P+
Release 5.0 04/09
Figure 8: Time until update